Toshiba CS3330Bi User manual

This specification subjects to change without notice.
D4134992A
CCD M o n o c h r o m e
Vi d e o C a m e r a
CS3330Bi S E R I E S
CS3330Bi CS3330BLi
Spe ci fic ati on
CONT E NTS
Before use – General safety instructions
1. PRODUCT DESCRIPTION ……… ..................................................................
1
2. FEATURES...................................................................................................
1
3. CONSTITUTION...........................................................................................
1
4. SPECIFICATIONS
4-1 Mechanica specifications ............................................................................
4-2 E ectrica specifications ................................................................................
2
2
5.APPEARANCES
5-1 Appearance of the camera head ..................................................................
5-2 Appearance of the camera head with mount meta fitting ..............................
5-3 Appearance of the camera contro unit for CCD camera (CS3330Bi)…….…
5-4 Appearance of the camera contro unit for CCD camera (CS3330BLi)……...
5
6
7
8

This specification subjects to change without notice.
D4134992A
BEFORE USE - GENERAL SAFETY INSTRUCTIONS
This instruction manual contains important information for the operator (user) and/or people in the
vicinity to avoid personal injury, or property damage.
• Prior to use, read this operation manual carefully to fully understand its instructions for correct use.
• After reading, keep this manual near the equipment for future reference.
WARNINGS & CAUTIONS
Definition of markings]
The meaning of each mark used in this instruction manual is given below.
Notes *1: Personal injury means wounds, burns, electric shocks, and others for which
hospitalization or long term care are not required.
*2: Material damage means any direct or consequential damage related to property or material loss.
WARNING
This mark warns the user that improper use may cause death or severe
personal injury of the user or people in the vicinity.
CAUTION
This mark warns the user that improper use may cause personal injuries
(*1) or material damages (*2) against the user or people in the vicinity.
This mark indicates what the user SHOULD NOT DO. The details are given adjacent the mark.
This mark indicates what the user MUST DO. The details are given adjacent the mark.

This specification subjects to change without notice.
D4134992A
●Handling Precautions
WARNING
unplug


 Immediately cea e u e of the equipment in the event of abnormality or malfunction.
If abnormal conditions are present, such as smoke, a burning smell, ingress of water or foreign
matter, or if the equipment is dropped or malfunctions, fire or electric shock may result.
If such abnormalities occur, disconnect the power plug from the outlet and contact your sales
representative.
Do not get wet


 Do not u e the equipment in location ubject to water pla he .
Otherwise, fire or electric shock may result.
Never pull apart


 Do not di a emble, repair, or modify the equipment.
Otherwise, fire or electric shock may result.
For internal repair, inspection, or cleaning, contact your sales representative.
Avoid


 Do not place anything on the equipment.
If metallic objects, liquid, or other foreign matter enters the equipment, fire or electric shock
may result.
Avoid


 Do not in tall the equipment in an un table or inclined location or location ubject to
vibration or impact.
Otherwise, the equipment may topple over and cause personal injury.
Do not touch


 During an electrical torm, do not touch the power cord or connection cable.
Otherwise, an electric shock may result.
Instruction


 U e the pecified power upply.
Use of an unspecified power supply may result in fire or electric shock.
Avoid


 Do not be handled roughly, damaged, fabricated, bent forcefully, pulled, twi ted, bundled,
place under heavy object or heated the power cord, connection cable.
Otherwise, fire or electric shock may result.

This specification subjects to change without notice.
D4134992A
CAUTION
Instruction


 Ob erve the following when in talling the equipment:
· Do not cover the equipment with a cloth, etc.
· Do not place the equipment in a narrow location where heat is likely to accumulate.
Otherwise, heat will accumulate inside the equipment, possibly resulting in a fire.
Avoid


 Do not place the equipment in location ubject to high moi ture, oil fume , team, or
du t.
Otherwise, fire or electric shock may result.
Avoid


 Do not in tall the equipment in location expo ed to direct unlight or humidity.
Otherwise, the internal temperature of the equipment will rise, which may cause a fire.
Avoid


 U e only pecified AC power cable and connection cable .
Otherwise, fire or electric shock may result.
Avoid


 When performing connection, turn off power.
When connecting the power cable or connection cable, turn off the equipment power.
Otherwise, fire or electric shock may result.
Avoid


 Do not expo e it camera head to any inten ive light ( uch a direct unlight).
Otherwise, its inner image pickup devise might get damaged.
Avoid


 Avoid hort-circuiting ignal output.
Otherwise, a malfunction may occur.
Avoid


 Avoid giving a trong hock again t the camera body.
If your camera is used in a system where its camera connector is subjected to strong repetitive
shocks, its camera connector is possible to break down. If you intend to use your camera in
such a situation, if possible, bundle and fix a camera cable in the place near the camera, and do
not transmit a shock to the camera connector.
Instruction


 Contact your ale repre entative to reque t periodic in pection and cleaning (every
approx. five year ).
Accumulation of dust inside the equipment may result in fire or electric shock.
For inspection and cleaning costs, contact your sales representative.

This specification subjects to change without notice.
D4134992A
CASES FOR INDEMNITY (LIMITED WARRANTY)
We hall be exempted from taking re pon ibility and held harmle for damage or lo e incurred by the
u er in the following ca e .
 In the case damage or losses are caused by fire, earthquake, or other acts of God, acts by a third party,
deliberate or accidental misuse by the user, or use under extreme operating conditions.
 In the case of indirect, additional, consequential damages (loss of business interests, suspension of business
activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from
responsibility for such damages.
 In the case damage or losses are caused by failure to observe the information contained in the instructions in
this instruction manual and specifications.
 In the case damage or losses are caused by use contrary to the instructions in this instruction manual and
specifications.
 In the case damage or losses are caused by malfunction or other problems resulting from use of equipment or
software that is not specified.
 In the case damage or losses are caused by repair or modification conducted by the customer or any
unauthorized third party (such as an unauthorized service representative).
 Expenses we bear on this product shall be limited to the individual price of the product.


 About the item which does not have a publication in the specifications and manual of this product, it
considers as the outside for a guarantee.
RESTRICTION FOR USE

Should the equipment be used in the following conditions or environments, give consideration to safety
measures and inform us of such usage:
1. Use of the equipment in the conditions or environment contrary to those specified, or use outdoors.
2. Use of the equipment in applications expected to cause potential hazard to people or property, which
require special safety measures to be adopted.
 This product can be used under diverse operating conditions. Determination of applicability of equipment or
devices concerned shall be determined after analysis or testing as necessary by the designer of such
equipment or devices, or personnel related to the specifications. Such designer or personnel shall assure the
performance and safety of the equipment or devices.
 This product is not designed or manufactured to be used for control of equipment directly concerned with
human life (*1) or equipment relating to maintenance of public services/functions involving factors of safety
(*2). Therefore, the product shall not be used for such applications.
(*1): Equipment directly concerned with human life refers to:
· Medical equipment such as life-support systems, equipment for operating theaters.
· Exhaust control equipment for exhaust gases such as toxic fumes or smoke.
· Equipment mandatory to be installed by various laws and regulations such as the Fire Act or
Building Standard Law
· Equipment related to the above
(*2) Equipment relating to maintenance of public services/functions involving factors of safety refers to:
· Traffic control systems for air transportation, railways, roads, or marine transportation
· Equipment for nuclear power generation
· Equipment related to the above

This specification subjects to change without notice.
D4134992A
Usage Precautions
 Handle carefully
Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may cause
malfunctions. Further, do not damage the connection cable, since this may cause wire breakage.
 Environmental operating conditions
Do not use the product in locations where the ambient temperature or humidity exceeds the specifications.
Otherwise, image quality may be degraded or internal components may be adversely affected. In particular,
do not use the product in areas exposed to direct sunlight. Moreover, during shooting under high
temperatures, vertical stripes or white spots (noise) may be produced, depending on the subject or camera
conditions (such as increased gain). However, such phenomena are not malfunctions.
 Do not shoot under intense light.
Avoid intense light such as spot lights on part of the screen because it may cause blooming or smears. If
intense light falls on the screen, vertical stripes may appear on the screen, but this is not a malfunction.
 Occurrence of moiré
If you shoot thin stripe patterns, moiré patterns (interference fringes) may appear. This is not a malfunction.
 Do not expose the camera’s image-pickup-plane to sunlight or other intense light directly.
Its inner CCD (charge-coupled device) might be damaged.
 Occurrence of noise on the screen
If an intense magnetic or electromagnetic field is generated near the camera or connection cable, noise may
be generated on the screen. If this occurs, move the camera or the cable.
 Handling of the protective cap
If the camera is not in use, attach the lens cap to the camera to protect the image pickup surface.
 If the equipment is not to be used for a long duration
Turn off power to the camera for safety.
 Maintenance
Turn off power to the equipment and wipe it with a dry cloth.
If it becomes severely contaminated, gently wipe the affected areas with a soft cloth dampened with diluted
neutral detergent. Never use alcohol, benzene, thinner, or other chemicals because such chemicals may
damage or discolor the paint and indications.
If the image pickup surface becomes dusty, contaminated, or scratched, consult your sales representative.
 Disposal
When disposing of the camera, it may be necessary to disassemble it into separate parts, in accordance with
the laws and regulations of your country and/or municipality concerning environmental contamination.

1
This specification subjects to change without notice.
D4134992A
1. PRODUCT DESCRIPTION
Model CS3330Bi/BLi is monochrome video camera with charge coupled device (CCD). These
cameras are composed of camera head and camera controller (CCU).
2. FEATURES
The video cameras have the following technical features.
(1) igh resolution
A 380,000 pixel CCD incorporated in the unit provides horizontal resolution of 570 lines.
(2) igh reliability
Realize extremely low graphic distortion and after-images levels. Offers high reliability, high
stability, long life and resistance against impact and vibration.
(3) Compact and light weight
The camera head and camera control unit are separately designed. The camera head is designed
to minimize use of parts and is ultra-compact and light weight.
(4) External synchronization
The unit is automatically switched over between internal and external synchronization. When
HD and VD signals are input from an external device, the external synch is automatically set
and HD and VD signals are output.
(5) Electronic shutter
Variable speed electronic shutter (TV sync) with 8 steps from 1/60sec to 1/10,000sec. (standard
feature)
(6) Electronic lines display (CS3330BLi)
Video signals can be overlapped using two sets of vertical and horizontal lines which are
displayed as electronic lines on the monitor. In addition, there is also an option of displaying a
reticle mark on the monitor to conveniently position and size up the images.
3. CONSTITUTION
Camera head without lens
( includes 3m camera cable )
1 set
Camera control unit (CCU) 1 set
Accessories
(1) Video cable
(3C-2V ,with BNC plug on both ends 0.5m)
1 set
(2) AC cable(2.0m) 1 set
(3) Fuse(0.5A / 250V) 2 set
(4) Camera head mount metal fitting 1 set
(5) Lens mount screw 1 set
(6) adapter(3P-2P) 1 set
(7) Operation manual (this document) 1 copy

2
This specification subjects to change without notice.
D4134992A
4. SPECIFICATION
4-1 Mechanical specifications
Overall dimensions and weight
Camera head: Refer to the attached camera head diagram.
Camera control Unit: 220(w) x 60(H) x 240(D) mm (excluding rubber casters)
Mass : approx. 2.6 kg
Camera cable: 6.3mm(dia.) x 3 m length
Lens mount: C mount
4-2 Electrical specifications
TV system:
Based on EIA standard
Pickup Device: Interline transfer CCD ICX422AL
Effective pixels: 768(H) x 494(V) pixels
Unit cell size: 11.6(H) x 13.5(V) micro m
Sensing area: 8.8(H) x 6.6(V) mm
(Equivalent to type-2/3 normal optical image
size respectively.)
Scanning method: 525 lines, 2:1 interlace
Sync. system: automatic switching between
internal / external synchronization
Scanning frequency: horizontal; 15.734kHz
Vertical; 59.94Hz
Aspect rate: 4:3
Subject illumination:
Standard: 100 lx, F4(3100K),(AGC OFF, gamma=1.0)
Minimum: 0.3 lx, F1.4,(gamma=0.45 with maximum gain)
Video output: VS: 1.0V(p-p)/ 75 ohm
Horizontal resolution: 570 TV lines
Vertical resolution: 350 TV lines
S/N: 56dB (AGC OFF, gamma=1.0 )
External sync input:
Input level: 2 to 6 V(p-p) for both HD and VD signals
Input impedance: 1 k ohm for both HD and VD signals
Method: 2:1 interlace
Polarity: Negative
Pulse width: HD: 6.4 +/- 3 micro sec
VD: 150 to 800 micro sec
Repeat frequency: fH =15.734 kHz±2%
fv =2 fH/525
Scanning lines: 525 lines

This specification subjects to change without notice.
D4134992A
Phase difference: The phase difference between the trailing edge
of VD and the trailing edge of HD must be as
shown below.
Output signal: HD,VD negative polarity
Level: 3.5 to 4.5V(p-p) / 1k ohm terminated
8.0 to 9.0V(p-p) / high
Pulse width: HD: 6.36±0.5 micro sec
VD: 572±5 micro sec
Repeat frequency: fH =15.73426 kHz
fv =2 fH/525
Scanning lines: 525 lines
Output circuit:
Electronic line display or reticle ( CS3330BLi ONLY )
NO. of lines: 2 horizontal lines, 2 vertical lines
Movable range: Entire monitor screen
Line width: Horizontal line: 1 scanning line/field
Vertical line: approx. 0.5 micro sec
Polarity : White(POSI) / black(NEGA) selectable
ON/OFF: switching
Electronic line / reticle: Internal selector switch
(Factory preset is electronic line.)
Gamma: 0.45/1 selectable
AGC: ON/OFF switching
2
nd
field
t2=1/fH / 2 +/-5 micro sec
t1＝0+/-5 micro sec
1
st
field
VD
HD
TD62504F
HD
VD
1k ohm
+9V

4
This specification subjects to change without notice.
D4134992A
Electronic shutter: ON/OFF switching
(TV synchronization):
Shutter speed: Selectable at 1/60sec, 1/125sec, 1/250sec,
1/500sec, 1/1,000sec, 1/2,000sec,1/4,000sec,
(during exposure): 1/10,000sec and flicker less
CCD operation mode: frame store mode
Power supply: AC100V +/-10%, 50/60Hz,150mA ± 20%
Ambient condition:
Temperature: From 0 through 40 degrees
Humidity: From 30 through 90% (No condensing)

5
This specification subjects to change without notice.
D4134992A
5. APPEARANCES
5-1 Appearance of the camera head

6
This specification subjects to change without notice.
D4134992A
5-2 Appearance of the camera head with mount metal fitting
C mount
Mount metal fitting
Lens mount
Cover
1/4-20 UNC depth:6
2-M3 depth:6
Frame
Specifications
Material:
Lens mount: Stainless steel
Frame, cover: Aluminum alloy
Mount metal fitting: Aluminum alloy
Finish coating:
Frame, cover: Black alumite finish
Mount metal fitting: Elidite finish

7
This specification subjects to change without notice.
D4134992A
5-3 Appearance of the camera control unit for CCD camera (CS3330Bi)

8
This specification subjects to change without notice.
D4134992A
5-4 Appearance of the camera control unit for CCD camera (CS3330BLi)