Toshiba IK-WB82A User manual

NETWORK CAMERA
Model: IK-WB82A
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations
and other information.
The application Adobe®Reader® is needed to view PDF les. If you do not have this
application, download it from the Adobe Systems Incorporated website.
nhttp://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
nhttp://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

22
Introduction
FCC (USA)-INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CAUTION: Your authority to operate this FCC veried equipment could be
voided if you make changes or modications not expressly approved by the party
responsible for compliance to Part 15 of the FCC Rules.

3
Thank you for purchasing the IK-WB82A Network Camera. Before using the
camera, read this Quick Start Guide and Important Safeguards ("Guide") carefully
to ensure correct usage. After reading this Guide, save it for future reference.
The design, specications, software, and this Guide's contents are subject to
change without prior notice.
Terms
lThe term "OS" is used in this manual to indicate operating systems compatible
with this product.
-- Microsoft®Windows®7 Professional Edition
NOTE
lThe performance of the network camera may vary depending on the network
environment.

44
Table of Contents
Introduction.......................................................................................................2
FCC (USA)-INFORMATION.......................................................................................2
Terms ........................................................................................................................3
Table of Contents..............................................................................................4
Important Safeguards.......................................................................................5
Important Safeguards (Cont.)...........................................................................7
Notes on Use and Installation...........................................................................8
Setting the Network Camera Environment.......................................................9
Items needed for network camera monitoring...........................................................9
Package Contents..........................................................................................10
Physical Description ........................................................................................11
Hardware Installation .....................................................................................12
Cabling Assembly ..........................................................................................14
Network Deployment .....................................................................................16
Assigning IPAddress......................................................................................18
Retrieving Images...........................................................................................19
Adjusting the direction and Silica Gel.............................................................20
Adjusting the Zoom and Focus.......................................................................21
Completion .....................................................................................................22
Trademarks ....................................................................................................23

5
Important Safeguards
1. Read Instructions
Read this Guide and User’s Manual before operating the product.
2. Retain Instructions
Retain this Guide and User's Manual for future reference.
3. Warnings
Acknowledge all warnings on the product and in the User's Manual.
4. Follow Instructions
Follow instructions in this Guide and User’s Manual.
5. Cleaning
Disconnect this product from the power supply before cleaning.
6. Attachments and Accessories
Do not use any attachment and accessories other than recommended and authorized
ones by the camera manufacturer as they may pose safety risks.
7. Mount the Product on Appropriate Place
Do not mount the product on an unstable cart, stand, tripod, bracket or table. The product
may fall, causing serious injury to a person, or serious damage to the product. Mount the
product only in places where Toshiba recommends in the Guide and/or the User's Manual.
8. Use the Product under Appropriate Temperature
This product should never be placed near or over a radiator or heat register. If this product
is placed in a built in installation verify that there is proper ventilation so that the camera
temperature operates within the recommended temperature range.
9. Power Sources
This product should be operated only from the type of power source indicated on the
information label attached to the product.
10. Power-Cord Protection
Power cords should be routed so that they are not likely to be walked on, pinched, or
damaged by items placed upon or against them. Pay particular attention to cords at plugs,
screws and the point where they exit the product.
11. Installation
Install this product on a secure part of the ceiling or wall. If installed on an unsecured
location, the product could fall causing injury and damage.

66
12. Lightning
If lightning occurs, do not touch the product or any connected cables in order to avoid
electric shock. This product may have damage due to lightning and power-line surges
during a lightning storm. For additional protection on this product, when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the
power supply and cable system.
13. Overloading
Do not overload the power supply or extension cords as it could result in a risk of re or
electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this camera through openings as they may touch
dangerous electrical points or short-out parts that could result in a re or electrical shock.
Never spill liquid of any kind on the camera.
15. Do Not Maintain the Product by Yourself
Do not x, repair or maintain the product by yourself. This may expose you to dangerous
electrical or other hazards. Refer all servicing to qualied service personnel.
16. Damage Requiring Service
Disconnect this product from the power supply and refer servicing to qualied service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been submerged in water.
d. If the product does not operate normally although you use it under the operating
instructions in the User's Manual. Adjusting or maintaining the product by yourself in a
manner not authorized by the User's Manual may result in damage and will often require
extensive work to restore the product to its normal operation.
e. If the product has been dropped or its cabinet has been damaged.
f. When the product exhibits a distinct change in performance which indicates a need for
service.
g. Any other trouble with the product.
17. Replacement Parts
When replacing parts be sure the service technician uses parts specied by the
manufacturer or have the same characteristics as the original part. Using unauthorized
replacement parts may result in re, electric shock or other hazards.
18. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.

7
Important Safeguards (Cont.)
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT SUBMERGE
THIS PRODUCT IN WATER.
FIELD INSTALLATION MARKING:
WORDED: “THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.”
The unit is intended to be supplied by an UL listed power supply suitable for using
at Tma min. 50 degree C and whose output rated 36-57Vdc, min. 340-210 mA or
12Vdc, min. 1.02 A and met SELV and LPS; an UL listed end-product suitable for
using at Tma min. 50 degree C and with "PoE" connector complied SELV and LPS
and rated 36-57Vdc, min. 340-210 mA.
The unit is to be connected only to PoE networks without routing to the outside
plant.
Ce produit est conçu pour être alimenté par un adaptateur secteur UL pour une
l’utilisation à Tma min. 50 degrés C et avec une sortie nominale de 36-57V DC,
min. 340-210 mA ou 12V DC, min. 1.02 A et conforme avec SELV et LPS; un
produit nal UL pour une utilisation à Tma min. 50 degrés C et avec un connecteur
"PoE" conforme à SELV et LPS et une sortie nominale de 36-57V DC, min. 340-210
mA.
L’appareil doit être connecté uniquement aux réseaux PoE sans routage à
l’equipement extérieur.
Tma: the maximum ambient temperature
SELV: Secondary Extra Low Voltage
LPS: Limited Power Source

88
Notes on Use and Installation
lDo not aim the product at the sun
Never aim the product at the sun even with the product power off.
lDo not shoot intense light
Intense light such as a spotlight to the product may cause a bloom or smear. A
vertical stripe may appear on the screen. However, this is not a malfunction.
lTreat the product with care
Dropping or impacting the product may cause it to malfunction.
lAvoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the product. Do not
leave rubber or plastic products on the product for a long time. They will leave
marks on the product. Do not use a chemically saturated cloth.
lNever touch internal parts
Do not touch the internal parts of the product other than the parts specied in
the User's Manual.
lDo not submerge in water
The product has some protection to water (see IP rating), and can be used
indoors or outdoors. If the product was submerged in water, turn off the power
and contact your dealer.
lKeep the product away from video noise
If cables of the product are wired near electric lighting wires or a TV set, noise
may appear in images. In this case, relocate cables or reinstall the product.
lCheck the ambient temperature and humidity
Avoid using the product where the temperature is hotter or colder than the
specied operating range in the User's Manual. Doing so could affect the
internal parts or cause the image quality to deteriorate. Special care is required
to use the product at high temperature and humidity.
lShould you notice any trouble
If any trouble occurs while you are using the product, turn off the power and
contact your dealer. If you continue to use the product with the trouble or
malfunction, the trouble may get worse and an unpredictable problem may
occur.

99
Setting the Network Camera Environment
Items needed for network camera monitoring
lAdministrator's personal computer
The personal computer that allows setting, operating, monitoring and other
functions with the network camera is called the "administrator's personal
computer" in this guide.
* The personal computer for viewing monitored images is called the "user's
personal computer" in this quick start guide. The network camera can be
viewed by more than one personal computer at the same time.
lRecommended personal computer system requirements:
-- Windows®7 professional.
-- Internet Explorer®Ver 11
-- CPU: Intel® CoreTM i3 or better
-- Memory: 1GB RAM or greater
lConnection equipment such as Ethernet cables, and switch or router.
-- The LAN cable type differs depending on the connection method.
lCamera search application "Installation Wizard"
-- Install this application from the CD-ROM supplied as an accessory (Double-click
"Setup.exe" in the CD-ROM and install the application by following the onscreen
instructions.)
-- This application is the tool to discover the IP address of a camera. Using this
application, the IP address of a camera can be easily determined.

1010
IK-WB82A
Ver. WB82-01
lIK-WB82A
lQuick Start Guide and Important
Safeguards
lSun Shield
Screws
Wrench
Tape
lWaterproof Connector
lAV Out Cable
lCD-ROM
lAlignment Sticker / Silica Gel
lWarranty
Package Contents
lWall Mount Bracket
Wall Mount Plate
Screw and Anchors Kit
Wrench
Spacer
lWaterproof Connector for RJ45
Ethernet Enclosure
NETWORK CAMERA
Model: IK-WB82A
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations
and other information.
The application Adobe®Reader® is needed to view PDF les. If you do not have this
application, download it from the Adobe Systems Incorporated website.
nhttp://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
nhttp://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

1111
Physical Description
SD/SDHC/SDXC
Card Slot
NOTE : When inserting an
SD card, note the orientation
of the contacts.
Front Side
Back Side
IR LEDs
Lens
Light Sensor
MIC In (RED)
General I/O
Terminal Block
Reset Button
Status LED
RJ45 Cable
Focus Button
Audio/Video out
(Green)
Back cover
Rotate
counterclockwise
1 GND
2Power Input (12V DC)
3 Do not use
4 Do not use
5 Signal GND
6 Digital Input
7 Digital output
812V DC Output
87654321
Pin Denition
NTSC-PAL switch
PAL NTSC
The 12V DC digital output “DO” is not supported when powered by PoE.
NOTE

121212
Hardware Installation
Notes:
lThe attached screws and anchors are used to install the camera to a solid surface.
(e.g. concrete) If installing to loose or thin material surfaces , use the appropriate
anchors (not included) with the screws.
lInstall the camera tightly.
Operating environment
–22 °F ~ 122 °F {–30 °C ~ +50 °C}
When the camera is installed and operated in low temperatures below 14 °F {–10 °C},
normal images may not be obtained immediately after startup. In such a case, wait until
the camera warms up (taking more than 1 hour) and start adjustment after turning on
the power again.
Mounting the camera to a solid surface
1. Attach the alignment sticker to the wall. Drill three pilot holes (Φ 9.5mm x 40mm(D)
(Φ 0.37inch x 1.57inch(D) )) and one big hole through the four circles on the sticker.
Then hammer the supplied plastic anchors into the holes and secure the plate with
supplied screws.
2. Stick the supplied spacer between the bracket and camera body. Use the two
supplied screws to x the bracket to the camera body.
3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want
to use external devices such as sensors and alarms, please refer to the assembling
steps on page 14.)
4. Push the spring bolt and hook the bracket onto the groove of the wall mount bracket.
5. Secure the two screws on the other side of the wall mount bracket.
6. Hang the wall mount bracket on the plate.
7. Fix the wall mount bracket with the supplied screw and spring washer.
8. Loosen the screw A and B with supplied wrench, and adjust the angle of the wall
mount bracket to aim at the shooting area. Then, secure the screw A and B with
supplied wrench.

13
1
2
4
3
5
6
7
8
B
A
lInstallation should be done only by qualied personnel and conform to all local codes.
lInstall this camera on a rm and solid part of the wall.
If installed improperly or on a weak surface, the camera could fall causing injury and
damage.
NOTE
CAUTION

14
Cabling Assembly
12
3
45
6
78
(D) (B) (C)
(A)
(E)
Components of the Waterproof
Connector
Screw Nut (C)
Housing (D)
Gasket (E)
Seal (B)
Sealing Nut (A)
RJ45 Cable Dimension (unit: mm)
Prepare an Ethernet cable
and strip part of the sheath. Insert the housing into the
screw nut. Insert the seal into the housing.
Insert the stripped Ethernet
cable through the sealing
nut and the housing.
Clamp the cable with
an RJ45 plug. Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
Attach the gasket to the front
of the housing.
Assembly Steps
Recommended cable gauge: 24AWG
(0.51 mm)
Connect the Ethernet cable to the RJ45 cable and secure the
connectors tightly.
RJ45 Cable Connector

15
Waterproof Connector
1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above.
2. Open the back cover of the Network Camera.
3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A)
tightly.
4. If you need extra power for external devices, please feed the power cable through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shows below. Then
connect the power cord to the socket. Note: There are 7 holes on the seal (B), and the widest hole
with a notch on the side is specic for power cord.
5. If you have external devices such as sensors and alarms, feed the cables through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then
refer to the pin denition to connect them to the general I/O terminal block. Note: The recom-
mended cable gauge is 2.0 ~ 2.8 mm.
6. Push the seal (B) into the housing (D).
7. Insert the seals (C) into the empty holes on the seal (B) to avoid moisture.
8. Secure the sealing nut (E) tightly.
9. Clamp all cables, nally.
Components of the Waterproof Connector
Seals (C)
Housing (D)
Sealing Nut (E)
Seal (B)
Screw Nut (A)
Assembling Steps
3
4
(E)
(D)
(B)
(A)
5
4
8
(E)
9
7
6
(C)
(B)
(D)
2
When using this waterproof connector, don't use attached bracket to hook the camera to the wall
mount bracket.
NOTE
1

16
Network Deployment
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
LAN cable. see the following illustration to connect the Network Camera to a PoE switch via LAN
cable.
When using a non-PoE switch
Use a PoE power injector (not supplied) to connect between the Network Camera and a non-PoE
switch.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Non-PoE Switch
(not supplied)
Client PC
(not supplied)
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
(not supplied)
Client PC
(not supplied)
For PoE input, use only UL
listed I.T.E. with PoE output.
PoE Power Injector
(not supplied)
For PoE input, use only UL
listed I.T.E. with PoE output.

17
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
1
2
Ethernet switch
(not supplied)
1. Connect the Network Camera to an Ethernet switch via LAN cable.
2. Connect the power cable from a power unit (not supplied) to the appropriate port of
the general I/O terminal.
(See page 11).
3. Connect the PC to an Ethernet switch via Ethernet cable.
3
lRecommended power cord is twisted pair line with a minimum wire size of 18 AWG.
lThe recommended power supply for this camera is 20 watts minimum.
lWhen PoE is connected, do not supply 12V DC to the I/O terminal.
120V AC
12V DC adapter
UL Listed power supply (not supplied)
NOTE
CAUTION
General Connection (without PoE)
Client PC
(not supplied)

18
MAC:0002D1714270
S/N: A1302XXXX
0002D1714270
00-02-D1-71-42-70 169.254.0.99 IK-WR12A
Installation
Wizard
1. Install the "Installation Wizard" under the Software directory from the CD-ROM.
2. The program will analyze your network environment. After your network is
analyzed, please click on the "Next" button to continue the program.
Assigning IP Address
NOTE
lIf "Installation Wizard" does not nd the camera during the search, try turning off the
wireless LAN of a PC.
lInstallation Wizard can search the location of the Network Camera even though
DHCP is not used on the network. In this scenario, assign the camera a static
IP address because the IP address of the Network Camera has been assigned
169.254.*.* by default.
3. The program searches for other Network Cameras on the same network.
4. After searching, the main installer window will pop up. Double click on the MAC
address of the appropriate device to connect to the Network Camera.

19
Retrieving Images
For more information on camera conguration, please refer to user's
manual on the CD-ROM.
1. Access to the Network Camera from the network.
2. Retrieve live video through Internet Explorer®.

20
Monitoring on the television
This camera is able to output an analog NTSC video signal and sound from the Audio/Video Out jack
in the backside of camera.
Adjustment of Viewing angle is possible using a portable monitor without using a personal computer
when installing. Use the included AV Out cable for this purpose.
Focus button
When adjusting the viewing angle, the camera focus may shift.
In this case, push the focus button in the backside of camera for 2 seconds or more. The zoom lens
will move to a wide position and the focus will move to the optimal position.
lDepending on an object's conditions, the focus may not move to the optimal position.
In this case, focus the lens manually from your personal computer.
1. Adjust the direction of the Camera to aim at the shooting area. (Refer page 12)
2. If you open the back cover when installation, replace the silica gel with a new one as follows.
3. You will nd a silica gel bag attached to the back cover.
Remove the silica gel from the back cover, and replace it to the new silica gel with supplied
double-sided tape in the aluminum foil bag.
(Please replace the silica gel with a new one if you open the back cover after installation.)
4. Secure the back cover to rotate it in clockwise direction. Make sure all parts of the camera are
securely installed.
Open
Close
Adjusting the direction and Silica Gel
IMPORTANT:
Zoom and Focus adjustment is made via the Remote Focus function on your web browser.
There is no mechanical zoom or focus adjustment for the camera.
NOTE
Treat silica gel bag with care. Do not tear the silica gel package.
WARNING:
Keep the silica gel out of the reach of babies, infants, and children.
DO NOT EAT, HARMFUL IF SWALLOWED