total sheds Pent Shed 7ft x 5ft User manual

Ready To Build - 5ft Range
Pent Shed Assembly Manual
Pressure Treated Tanalised Timber for Longer Lasting Life!
Version 1.4
Thank you for purchasing your Total Shed.
All of our sheds are made from only the nest selected timber which are
(Tanalised), specially pressure treated for a longer and lasting durable life
span to the elements.
Each shed is carefully packed and delivered on a pallet
ready to be assembled.
FEATURES NEW FLEXIBLE,
INTER-CHANGEABLE DESIGN
FORYOUR INDIVIDUAL STYLE.
DELIVERED FLAT PACKED IN
EASY TO INSTALL SECTIONS
2 Persons Recommended for Assembling Shed
PLEASE NOTE: Use extreme caution when using any tools. Always wear safety gear where
necessary. It is advisable that at least 2 or more persons assemble the shed for health and safety
purposes. We are not responsible for any injuries caused whilst assembling this shed.
Ready to Build Shed
Includes 4x5ft to 20x5ft Instructions
Featured Build of the Pent 7ft x 5ft Shed
DRILL DRIVER HAMMER HAND SAW STANLEY KNIFE
Tools Required:
www.totalsheds.co.uk
© Sheds (Midlands) Limited 2021
Total Sheds
Unit 1 Park Lane,
West Bromwich, B21 8LE
Tel: [phone]
Email: [e-mail]

+


4x5ft 4x5ft
4x5ft
4x5ft 4x5ft 4x5ft
4x5ft
4x5ft
2x5ft
3x5ft
















2x5ft
3x5ft
+
+
4x5ft
+
+
2x5ft
3x5ft
4x5ft
+
2x5ft
+
+
+
4x5ft
3x5ft
+
+
4x5ft
+
4x5ft
PRE-ASSEMBLY STEP • 1
02
Unpack all of the components and check that
you have all the parts required. Please use the
checklist on previous page.
Carefully dispose of the delivery pallet and
any excess timber.
Advisable: The underside of the oor must be
treated with a quality wood preserver.
Recommended: Paint shed
in an oil based treatment to
prevent water ingress into
the timber. Also silicon your
windows (Must silicon inside &
outside) to prevent rain water
seeping through the gaps
between glass and the timber.
SHED FLOOR: Setting Shed Base
Unpacking your Parts
SET THE SHED FOUNDATION
This Manuals Diagrams are based on the
7ft x 5ft Pent Shed
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Floor Section
3ft Floor
1b
5ft Floor
4ft Floor


4x5ft 4x5ft 4x5ft 4x5ft 4x5ft 4x5ft 4x5ft














+
+
4x5ft
+
4x5ft
+
+ +
4x5ft
+
+
4x5ft
+
+
2x5ft
3x5ft
4x5ft
+
4x5ft
+
4x5ft
4x5ft
+
4x5ft
3x5ft
+
+
2x5ft
4x5ft
+
4x5ft
+
4x5ft
+
4x5ft
+
+
2x5ft
3x5ft
4x5ft
+
4x5ft
+
4x5ft
+
2x5ft
+
4x5ft
+
4x5ft
3x5ft
+
4x5ft
+
4x5ft
+
4x5ft
1a. Secure the Floor Panels sections together by screwing the
oor bearers at each end where they meet as shown in diagram
1a.
1b. In this example, the shed starts o with a smaller oor panel.
With some other sizes, you will begin with a 4ft Floor Panel on the
left, and the smaller Floor Panel (2ft or 3ft) will be at the very right
of the build. Check the oor plan to the left if needed.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 2 STEP • 3
03
IMPORTANT
All Sheds With 4 or
More Floor Pannels
have the smallest Floor
Panel on the Right End.
As shown on this diagram.
2a. Place the 5ft long Floor Block Ends
provided on both ends of the oor
alongside existing oor bearers as
shown below.
2b. Fix together by screwing the Floor
Blocks at each end as shown. Use the
screws provided and make sure the
ends are xed securely. 2 screws on
each Floor Block will suce.
(Repeat for other side)
FLOOR & BLOCK ENDS
Add the Floor Block Ends
(Heavy Duty Posts)
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
Per Floor Block
FLOOR PANELS
2ft BLANK
2a
2FT LEFT SIDE PANEL
2ft RIGHT SIDE PANEL
Place rst panel againts
far right of shed oor
as shown.
(2ft wide blank panel)
3a. Place the 2ft Blank Panel against the far right side of the Shed Floor. Make sure the panel
stands rmly on the Heavy Duty Post (Floor Block).
3b. Now prepare the 4ft Blank Panel in order to create an ‘L’ shape in the corner with the two
panels.
3c. DO NOT x the panels at this stage to the
oor. This is because you need to leave room for
adjustements in the nal stages of the shed build.
FLOOR BLOCKS
REMEMBER The Panel should sit on the Floor
Block.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

INFORMATION
Not all Sheds will have the
same panel arrangment.
Please Ensure that the 4ft
Panels are central for all
builds.
STEP • 4 STEP • 5
04
= Drill Points using
screws provided as shown
= Drill Points using
screws provided as shown
x3 x3
x3 x3
4.0 x 70mm 4.0 x 70mm
Per Panel Edge Per Panel Edge
3ft SIDE PANEL
3ft SIDE PANEL
Place second panel againts
far right of shed oor as
shown. (3ft wide blank
panel)
5a. Place the 3ft blank panel as shown along the side of the shed oor aligning with the edge
of the side Floor Block.
5b. DO NOT x the panels to the oor to leave room for adjustments in the nal stages.
NOTE: Place panel
to sit rmly on the
side Floor Block. See
Diagram 5a
4b
5a
SIDE & REAR PANELS
SIDE & REAR PANELS
Fix 4ft Wide Blank
Sections. Create a Corner
for Balance.
4a. Place a 4ft Blank Panel side as shown below. Repeat this step for all larger sheds. Please use
reference on left for additional sections required according to your shed size.
4b. Screw the panels alongside the framework as shown in Diagram 4b.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 6 STEP • 7
05
3ft REAR PANEL
= Drill Points using
screws provided as shown
= Drill Points using
screws provided as shown
x3 x3
x3 x3
4.0 x 70mm 4.0 x 70mm
Per Panel Edge Per Panel Edge
LEFT PANEL
3ft REAR PANEL
Fix 3ft Wide Blank Section
Back Panel 3ft Section
(This panel might be 4ft depending on the
shed )
6a. Now place a 3ft Blank Panel side as shown. Repeat this step for all other sheds. Please use
reference on above for correct sections required according to your shed size.
LEFT SIDE PANEL
Fix 2ft and 3ft Wide Blank
Panel (Left)
7a. Place the 2ft Blank Panel side against the
corner of the back 3ft oor as shown making sure
the panel is sitting rmly on the shed oor and the
side meeting the framework of the back 3ft or 4ft
Blank Panel.
7b. Fix the panels together with screws as shown in
the diagram. You may require some supports to keep
the frame upright whilst building longer sheds.
7c. Repeat the previous step until the
walls of the shed are complete.
REMEMBER the Blank Panel should but
up to the end of the Floor Panel, sitting
nicely on to the Floor Block.
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

x3
STEP • 8 STEP • 9
06
= Drill Points using
screws provided as shown
DID YOU KNOW?
Door panels can be placed anywhere a 3ft panel is. The 3ft Door must be placed opposite
the 3ft back panel and on top of a 3ft oor.
FRONT DOOR PANEL
FRONT DOOR PANEL
Attach Door Front Panel
(3ft Door Panel)
(This panel might be 4ft depending on the
shed )
8a. Now place the 3ft Door Panel as shown. Fix together with screws to the left Blank Panel
framework.
= Drill Points using
screws provided as shown
x3
x3
4.0 x 70mm
Per Window Panel
4ft FRONT WINDOW PANEL
FRONT WINDOW
PANEL
Attach Front
Window Panel
(4ft Window Panel)
DID YOU KNOW?
Window panels can be placed anywhere
a corresponding panel is. This counts for
the door panel also.
9a. Use the RED areas below as reference to
the joining points of the nal panel. Note the
4ft section should t perfectly to continue the
front section.
9b. Place 4ft Window Panel as shown and x in
place at the meeting points with screws. Fix the
panel sides with 3 screws.
x3
4.0 x 70mm
Per Panel Edge
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 10 STEP •11
07
= Drill Points using
screws provided as shown
x3
x2
4.0 x 70mm
5ft SIDE PENT ANGLE TOPS
SIDE PENT ANGLE TOPS
Now attach all the 5ft
Side Tops of Pent Shed
End Panels. (Over the top
of both side panels).
Per Angle Top
10a. Now place the 5ft slope together and use two 70mm screws to secure them together, making
sure that they are in line. 10b. Once the Pent Angle
Top has been constructed,
use the screws to secure
the Angle Tops to the sides
of the Shed.
= Drill Points using
screws provided as shown
x3
x2/3
4.0 x 70mm
Per Front Top
PENT FRONT TOPS
PENT FRONT TOPS
Place the front tops of
shed in relation to the
fronts panels
11a. Place the Pent Front Top sections in place.
Make sure the correct section is placed on top
of the correct front panel only as shown in the
diagram.
11b. Adjust the panels so that the tounge &
groove are xed together in place correctly.
Use a hammer to lightly tap in to the grooves
to create a perfect t.
11c. Attach the sections
down by screwing
through the inner
framework of both
panels.
INFORMATION : Place
the 3ft Pent Front Top
ontop of the 3ft front
panel (Each Pent Front
Top should be placed
ontop of the correct
sized front panel)
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 12 STEP •13
08
= Drill Points using
screws provided as shown
x4
4.0 x 100mm
Per Roof Panel
PENT ROOF PANELS
PENT ROOF PANELS
Place 4ft Roof section.
Repeat for all Roof Panels
12a. Place the 4f Roof Panel in place.
Repeat this stage for models as shown
below. Repeat placing the roof panels
corresponding to the panel size for the
Floor Front an Rear. Repeat this for all
roof panels, making
sure each panel
is sitting on its
corresponding sized
front/back panel.
= Drill Points using
screws provided as shown
x3
x3
4.0 x 70mm
SIDE & CORNER STRIPS
SIDE & CORNER STRIPS
Hide the panel edges.
Cover the framework &
seams.
13a. Use all the Side/Corner Strips
to nish o the shed, by covering any
exposed framework and the panel
joining seams.
INFORMATION
Use these 100mm
screws to secure
the Roof panels
together.
12b. Screw the Roof Panel down by screwing into
the sides of the frame posts. The Roof Panels will sit
nicely inside of the Angle Tops as shown the next
step.
Per Corner Strip
13b. Fix the strips down by using 3 screws to secure
them to the Shed. This will create a nice nish and
hide any gaps on the outer walls of framework, front
and back.
14b
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 14 STEP • 15
09
14b
TACKS PROVIDED
ATTACH THE ROOF FELT
Use the felt lengths
provided.
15a. Apply the roof felt as shown. Apply lower levels rst to create
correct rain run o positions.
15b. Using a hammer, tack down the felt with the tacks provided in a
neat fashion.
15c. Trim down excess felt with a stanley knife. Remember
to overlay the 1st felt to avoid rain leaks.
15d. Tuck and fold edges neatly and tack in place to hide
any loose edges. Check that all areas are covered and
there are no holes to avoid any rain water getting through
your felt roof.
ROOF FELT
3rd
CUTTING THE ROOF
FELT
Use the felt table to cut
your felt to the correct
size
14a. Use the Stanley knife to cut your felt into the correct size. Using the table below, nd the Build
size that you have and cut your felt down to achieve the size that you will need.
Example:
Pent Shed 7ft x 5ft
The 7 by 5 needs 3 sheets of felt. All at 8ft each.
CUTTING THE ROOF FELT
4ft (x2) 5ft (x3) 6ft (x3) 7ft (x4) 8ft (x5)
4ft 5ft 5ft 5ft 5ft 5ft
5ft 6ft 6ft 6ft 6ft 6ft
6ft 7ft 7ft 7ft 7ft 7ft
7ft 8ft 8ft 8ft 8ft 8ft
8ft 9ft 9ft 9ft 9ft 9ft
9ft 10ft 10ft 10ft 10ft 10ft
10 ft 11ft 11ft 11ft 11ft 11ft
11 ft 12ft 12ft 12ft 12ft 12ft
12 ft 13ft 13ft 13ft 13ft 13ft
13 ft 14ft 14ft 14ft 14ft 14ft
14 ft 15ft 15ft 15ft 15ft 15ft
15 ft 16ft 16ft 16ft 16ft 16ft
16 ft 17ft 17ft 17ft 17ft 17ft
17 ft 18ft 18ft 18ft 18ft 18ft
18 ft 19ft 19ft 19ft 19ft 19ft
19 ft 20ft 20ft 20ft 20ft 20ft
20 ft 21ft 21ft 21ft 21ft 21ft
Build Length
Build Depth
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk

STEP • 16 STEP • 17
10
= Drill Points using
screws provided as shown
x3
x2/3
4.0 x 38mm
FELT STRIPS
ATTACH FELT STRIPS
Create the Final Roof
Edges. Final steps
nishing o the roof.
16a. Using the Felt Strips provided cover the edges of the roofs and ends of the roof felt. You will
need to measure these and saw to t to your requirements and create the perfect roof nish as
shown below.
16b. Drill in the felt strips as shown on front and back of the shed to nish the roof o. Use the
framework of the roof blocks to screw the felt strips down to. The felt strips will give your shed a neat
nish for the roof and hide any overhang areas of the roof felt.
NOTE:
Location of the Felt Strips
16c. Felt Strips must be same height as roong
felt to allow rain water to run o. See Diagram on
the right.
x3
x1
4.0 x 38mm
DIAMOND CAPS
DIAMOND CAPS
Add the Finishing
Touch. (Optional)
Timber is a naturally grown product and may shrink and warp when dried out, timber is a porous
material which can absorb water. Although all of our buildings come pressure treated we strongly
advise the building is re-treated with an oil/spirit based treatment inside and out to make the timber
water repellent and to preserve the quality and life of the product.
Congratulations
Per Felt Strip Per Diamond Cap
© Sheds (Midlands) Limited 2021 www.totalsheds.co.uk
Total Sheds
Unit 1 Park Lane,
West Bromwich, B21 8LE
Tel: [phone]
Email: [e-mail]