Totem MINI SHOOTER User manual

6x Beam 11 cm 1x Beam 7 cm 1x Beam 5 cm 4x 2-hole simple bracket 2x L-twisted bracket 2x L-twisted mirror bracket
1x Strip bracket 45 mm
(9 holes) 31x Nut M3 6x10 4x Threaded nylon spacer M3x8 mm 4x Nylon spacer 8mm 3x Cap nut M3 1x Bolt M2,5x8
27x Bolt M3x6 1x Bolt M3x10 4x Bolt M3x16 1x Bolt M3x20 7x Bolt M3x25 2x Shoulder bolt L8 M3x12
2x 43mm D-shaft wheel 2x 43mm O-shaft wheel 4x 43mm wheel ring (3D) 2x 43mm wheel bracket
(3D)
2x N20 motor bracket
4 (3D)
2x N20 motor 75:1 6V
400 rpm
1x Pistol left half (3D) 1x Pistol right half (3D) 1x Mini servo motor with
arm and bolt 1x Mini servo motor 1x Trigger (3D) 1x Washer 2,5mm (3D)
1x Battery holder (3D) 1x Trigger gear (3D) 1x Hook (3D) 3x Cable clip 22x Rubber band 40mm 1x Mini battery 3,7V
1x Mini battery charger 1x Mini Control Board X3 1x Socket wrench (3D) 1x Hex key 2mm 1x Totem screwdriver
PART LIST

BATTERY CHARGING:
Rechargeable battery must be charged by adult only.
• The new battery pack needs to be charged before use.
• Connect the USB charging cable to 5V USB power source, such as a
laptop.
• Connect the battery to the charger. The charger will show a red LED light
when charging the battery. When the battery is fully charged, the red
LED light turns o.
• To disconnect cables, hold the connectors of both cables and pull apart.
• Do not attempt to overcharge the battery.
START WITH
CHARGING THE BATTERY

Some of the nuts (~1%) are missing threads. This is a
manufacturing issue. We are trying to minimize the fault.
In the meantime, we supply extra nuts in your kit. We apologize
for the in-convenience.

1x Beam 11 cm 4x Nut M3 6x10
1
Pro tip:
You will need in
this step:
1. Use the back of
the screwdriver to
push in the nuts.
2. After entering the rst
slot, nuts tend to tilt. Use
your thumb to push it
back straight, and then
again use the screwdriver
to insert the nut all the
way in.

2x Wheel bracket 2x Nut M3 6x10
2
2x

1x Bolt M3x16
3
You can also use Beam/Bolt ruler to
determine the length of beams and bolts

2x N20 motor bracket 2x N20 motor
4
Position of the motor - cables down
2x

1x Bolt M3x16
5

4x Wheel ring 2x 43mm O-shaft wheel 2x 43mm D-shaft wheel
6
Up-side down
Make sure the rings sit tightly

1x 43mm D-shaft wheel +
Wheel ring
1x Nylon spacer 8mm
7

1x 43mm O-shaft wheel +
Wheel ring
1x Nylon spacer 8mm 1x Shoulder bolt L8 M3x12
8

2x Bolt M3x6 2x 2-hole simple bracket 1x Beam 11 cm 6x Nut M3 6x10
9

2x Bolt M3x6 1x Beam 11 cm 4x Nut M3 6x10
10

1x Bolt M3x6 1x L-twisted mirror
bracket
11
Step 10

1x Bolt M3x6 1x Mini servo motor with arm 1x Nut M3 6x10
12
Use Hex Key
in this step

1x Bolt M3x6 1x L-twisted bracket
13

1x Bolt M3x6 1x Nut M3 6x10
14

1x Bolt M3x16
15
Gap
Make sure cable holder does
not climb on the beam

1x Bolt M3x16
16
Position of cables