
3 4
Service condition and attentions in using
Use condition
1. Cold water supply*hot water supply pressure
Minimum pressure ………………… 0.05MPa (flow pressure)
Maximum pressure ………………… 1.0MPa (static pressure)
2. The temperature for water supply is 4~90℃. It is suggested to use the hot water
temperature of 60±5℃. Do not use steam to supply hot water.
3. The ambient temperature for use is above 0℃. If not, the water tap may deform and
crack due to freezing.
4. To prevent internal sprinkler damage,the water outlet temperature on the sprinkler
side shall not exceed 60℃.It is suggested to use a temperature below 45℃.
5. Being out of use for a long time may result in internal and external rust to the
water nozzle and being unable to be used.
6. If you want to scrap this product, do not treat it as you do for general domestic
garbage. Please follow relevant statutes to have it treated, recovered and collected
appropriately by an independent recovery system.
7. The product in these instructions has a cleaning function.
Attentions in using
Warning:it means that ignoring this mark and misoperation may cause serious
personal injury and death.
Attention: it means that ignoring this mark and misoperation may cause
personal injury or property loss.
Warning
Attentions in using and maintenance
Maintenance
To maintain a beautiful appearance of the product, the user is requested to
conduct maintenance and care in the following method.
1. Wipe with a piece of soft cloth frequently and use a piece of soft cloth
dipped in water to wipe from time to time.
2. When dirt exists obviously, please use water to wash sufficiently after
wiping with a neutral detergent.
Attentions
1. As the ceramic spool is a precise component, do not dismantle it without
authorization. Otherwise, such poor conditions as water leakage, etc. may be
caused.
2. Do not impact the product. Otherwise, failure, water leakage may occur.
3. It is imperative to use a neutral detergent in cleaning. Other detergents than a
neutral one may damage the plating coat or make the surface discolor.
4. Do not use any such detergent as acidic detergent and abstergent, polishing
powder, etc.containing thick particles and nylon brush. Otherwise, the plating
coat may be damaged, etc.
5. It is allowed to use a piece of soft cloth to wipe or use from time to time a
piece of cloth immersed in machine oil or vehicle wax to wipe. However, do
not contact with resin components. Otherwise, they may lose the gloss and
become rusty.
6. It is suggested not to leave it unused for a long time. Otherwise, this may lead
to internal and external rust to water nozzle to such a degree that it cannot be
used any more, etc.
7. With the product design being updated constantly, the physical object may not
coincide with the figure. However, the basic principle for installation, use is the
same.
1.Children are not allowed to use or can use only under the custody of adult. Such
special groups as the aged and disabled should be accompanied by those with
behavioral competence when using it.
2.The hot water supply side of the water nozzle is in a condition of high
temperature. Do not allow skin to contact with the hardware surface directly.
Otherwise,scalding may occur.
3.Do not reverse cold*hot water pipes. Otherwise, scalding may occur.
4.Do not use steam to supply hot water. Otherwise, scalding may occur.
5.When shifting directly from the water outlet to the shower side or shifting from
shower side to water outlet,the water temperature will change so test water
temperature to avoid scalding before using.
6.If a customer fails to use the self-contained water inlte filter net of our water
faucet,there is such a risk as water leakage or damage due to foreign matters
entering into the spool.
7.In constuction,do not install and use the G1/2 or G3/4 internal threads of this
product with R1/2 or R3/4 connector. Otherwise,the main body threads may
crack,resulting in such quality problems as water leakage,etc.