Toto GO TLG01310 Instructions for use

OG4111Y
2017.03
Instructions for construction
Before product installation, read these instructions for
construction carefully and retain it for future reference.
施工说明书

目录 明细单
目 录……………………………………1
明细单……………………………………2-3
使用条件与施工上的注意………………4
施工上的注意与保养……………………5
安装完成图………………………………6
水嘴的安装………………………………7-11
生产厂家与销售商………………………12
埋墙本体部………………………………1套
吐水本体部………………………………1套
手柄部……………………………………1套
固定接手…………………………………1套
装饰盖（大孔）…………………………1个
装饰盖（小孔）…………………………1个
螺钉………………………………………2个
吐水口治具………………………………1个
防水布……………………………………2个
施工说明书………………………………1本
使用说明书………………………………1本
1 2

使用条件与施工上的注意
使 用 条 件
施 工 上 的 注 意
警告
1.供冷水*热水压力：
最低压强…………0.05MPa（流动压）
最高压强…………1.0MPa（静压）
推荐使用压强……0.1-0.5MPa（流动压）
检测压强…………1.6MPa（静压）
2.供水温度在4℃～90℃，建议使用温度60℃，供热水请勿使用蒸汽。
3.使用环境温度0℃以上。如果低于0℃，水嘴会出现变形、冻裂等现象。
4.长时间不使用时，可能导致水嘴内部及外部锈蚀不能使用等现象。
5.如果您需要废弃本产品，请勿将其作为一般生活垃圾处理，请依照法规经
由独立的回收体系进行合适的处理、恢复和回收。
6.本说明书中的产品具有清洗功能。
表示如果无视此标志而误操作时，有可能造成人员重伤或死亡。
表示如果无视此标志而误操作时，有可能造成人身伤害或财产损伤。
1.水嘴的供热水一侧处于高温状态，请勿使皮肤直接接触五金配件表面，
否则可能会烫伤。
2.请勿配反冷*热水配管，否则可能会烫伤。
3.供热水请勿使用蒸汽，否则可能会烫伤。
警告
注意
明细单
使用此明细单的产品包括:
TLG01310* 铜合金壁式单柄双控暗装洗面器水嘴
TLG01311* 铜合金壁式单柄双控暗装洗面器水嘴
TLG02310* 铜合金壁式单柄双控暗装洗面器水嘴
TLG02311* 铜合金壁式单柄双控暗装洗面器水嘴
TLG03307* 铜合金壁式单柄双控暗装洗面器水嘴
TLG03308* 铜合金壁式单柄双控暗装洗面器水嘴
TLG04309* 铜合金壁式单柄双控暗装洗面器水嘴
TLG04310* 铜合金壁式单柄双控暗装洗面器水嘴
TLS01309* 铜合金壁式单柄双控暗装洗面器水嘴
TLS01310* 铜合金壁式单柄双控暗装洗面器水嘴
TLS02307* 铜合金壁式单柄双控暗装洗面器水嘴
TLS02308* 铜合金壁式单柄双控暗装洗面器水嘴
TLS03307* 铜合金壁式单柄双控暗装洗面器水嘴
TLS03308* 铜合金壁式单柄双控暗装洗面器水嘴
TLS04308* 铜合金壁式单柄双控暗装洗面器水嘴
TLS04309* 铜合金壁式单柄双控暗装洗面器水嘴
3 4

施工上的注意与保养
1.由于陶瓷阀芯是较精密的部件，请勿擅自分解，否则可能会造成漏水
等不良。
2.请勿撞击本产品，否则可能会造成故障、漏水。
3.随着产品式样的不断更新,实物存在与图示不符的情况,但基本安装、
使用原理相同。
4.由于出厂前进行通水检查，故水嘴内可能有残留水，并非产品有问题。
为长期保持产品的美观，请用户按以下方法维护保养。
1.经常用软布擦拭，间或用软布蘸水擦拭。
2.当有污垢且比较明显时，请用中性洗涤剂擦拭后充分进行水洗。
注意
保养
安装完成图
TLG01310* 铜合金壁式单柄双控暗装洗面器水嘴
注：上记尺寸单位为mm；
( )内尺寸为参考尺寸。
34
46
76
107
45
47
120
混合水
约57。
约57。
红色 蓝色
冷水
热水
8
52
给水中心
17
关闭
开启
G1/2
70±13
192
100
G1/2
(175)
8
(200)
11°
推荐安装距离150
洗面盆上端面
φ
约
2
2
°
5 6

水嘴的安装 水嘴的安装
MAX
MIN
70±13
17

52
94
(162)
120
完成墙面 供热水管 供冷水管
5.5
100
MAX
MIN
70±13
17

51
完成墙面
最大 60
76
(162)
120
供热水管 供冷水管
5.5
100
安装到一体化浴室等，护墙板和层板上
：
如图所示，用水泥等填料将产品安装在墙内。
如图所示，用螺钉将产品固定到墙面上。
※请根据需要另外准备合适的螺钉
护墙板、层板
混凝土砌块
4-10
刀锯 螺丝刀
六角扳手
（对边2.5mm）
浴室用粘贴剂
■确认供水管已经关闭，确认安装前水路进行清洗了。
■仔细阅读施工说明书并按照说明书的安装要领来进行安装。
1.事先把水嘴主体和相应的管子连接好，然后参照图示尺寸在
墙面开槽,否则水嘴安装时可能会出现问题。
固定螺钉
※必要：安装时使用水平仪对埋墙本体进行校正，使水平、垂直在最
佳状态。
水平 垂直
防水布（2个）
防水胶
安装前准备的工具 安装到混凝土砸块
安装前确认
一、水嘴主体的安装
7 8

注 意
注 意
水嘴的安装 水嘴的安装
二、吐水口部及手柄部的安装
1.使用刀锯将树脂保护套切除，
需要保证树脂套凸起边缘与墙
面在2mm以内。（边缘也不能凹
陷于墙面以内）
内套
保护盖
2.手柄部的安装：
a.抽出内套(注：安装完了后内套将不再起作用）。
b.将装饰盖套在阀芯套上，贴近墙面即可。（注：为方便安装
可将装饰盖内的O型圈涂少量的肥皂水进行润滑）
c.手柄安装到阀芯上，并用螺钉将其固定，表示盖安装在螺钉孔
位置。
2mm
以内
六角扳手
（对边2.5mm）
表示盖
螺钉
阀芯
装饰盖
手柄
内套
（抽出）
●在切割时注意不要割伤
内套，以免划伤内部阀
芯套。
2.将防水布穿过树脂套，使用浴室
用粘贴剂将其粘在水泥墙面上。
防水布
3.粘贴剂完全干燥之后，再将瓷
砖安装完毕（瓷砖开孔尺寸见
下图）。在树脂套与瓷砖的缝
隙中均匀涂上防水胶，且胶面
不能凸出墙面。 完成墙面
浴室用粘贴剂
53-60
100

53-60
瓷砖开孔尺寸（单位：mm）
●安装埋墙本体时，请不要将树脂套、
内套取下。
●安装时，请注意埋墙本体的埋入深度,
请保证完成墙面在保护套上MIN―MAX
标志之间。
●进水管与埋墙本体连接并确认各连接
处不漏水再加水泥填料。
树脂套
内套
水泥墙面
910

水嘴的安装
3.吐水口部的安装：
a.将固定接手插入埋墙本体扣到墙面上 ，并用2个螺
钉将其紧固。
b.将装饰盖穿过固定接手，吐水本体部与
固定接手连接，使其与装饰盖完全贴紧，
调整好装饰盖与吐水本体位置后，将吐
水本体用螺钉紧固。
六角扳手
（对边2.5mm）
螺钉
螺钉
螺丝刀
吐水本体
固定接手
[phone]
800-820-9787
400-820-9787
11 12
GB 18145-2014、GB 25501-2010

Contents
Wall embedded body part
Spout body part
Handle part
Fixed connecter
Decoration cover (large hole)
Decoration cover (small hole)
Screw
Spout jig
Waterproof cloth
Installations for construction
Instructions for operation
1 set
1 set
1 set
1 set
1 piece
1 piece
2 pieces
1 piece
2 pieces
1 copy
1 copy
Detailed list
Detailed list
1 2
Contents
Detailed list
Use condition and attentions in
construction
Attentions in construction and
maintenance
1
2-3
4
5
6
7-11
Installation completion figure
Faucet installation

Detailed list
3 4
The products using this detailed list inclucle:
TLG01310* "GO"Wall Mounted Single Lavatory Faucet (Short)
TLG01311* "GO"Wall Mounted Single Lavatory Faucet (Long)
TLG02310* "GR"Wall Mounted Single Lavatory Faucet (Short)
TLG02311* "GR"Wall Mounted Single Lavatory Faucet (Long)
TLG03307* "GS"Wall Mounted Single Lavatory Faucet (Short)
TLG03308* "GS"Wall Mounted Single Lavatory Faucet (Long)
TLG04309* "GA"Wall Mounted Single Lavatory Faucet (Short)
TLG04310* "GA"Wall Mounted Single Lavatory Faucet (Long)
TLS01309* "LB" Wall Mounted Single Lavatory Faucet (Short)
TLS01310* "LB" Wall Mounted Single Lavatory Faucet (Long)
TLS02307* "LN" Wall Mounted Single Lavatory Faucet (Short)
TLS02308* "LN" Wall Mounted Single Lavatory Faucet (Long)
TLS03307* "LC" Wall Mounted Single Lavatory Faucet (Short)
TLS03308* "LC" Wall Mounted Single Lavatory Faucet (Long)
TLS04308* "LF" Wall Mounted Single Lavatory Faucet (Short)
TLS04309* "LF" Wall Mounted Single Lavatory Faucet (Long)
Use condition and attentions in construction
Use condition
1. Cold water supply*hot water supply pressure
Minimum pressure ……………… 0.05MPa (flow pressure)
Maximum pressure ………………1.0 MPa (static pressure)
Recommended Operating pressure …… 0.05MPa (flow pressure)
Test pressure …………………… 1.0 MPa (static pressure)
2. The temperature for water supply is 4~90ºC. It is suggested to use the temperature
of 60±5ºC. Do not use steam to supply hot water.
3. The ambient temperature for use is above 0ºC. If the ambient temperature is lower
than 0ºC, the faucet will deform and crack from freezing.
4. Being out of use for a long time may result in internal and external rust to the faucet
and being unable to be used.
5. If you want to scrap this product, do not treat it as you do for general household
garbage. Please follow relevant statutes to have it treated, recovered and collected
appropriately by an independent recovery system.
6. The product in these instructions has a cleaning function.
Attentions in construction
Warning
Warning: it means that ignoring this mark and misoperation may cause serious
personal injury and death.
Attention: it means that ignoring this mark and misoperation may cause personal
injury or property loss.
1. The hot water supply side of the faucets is in a condition of high temperature. Do not
allow skin to contact with the hardware surface directly. Otherwise, scalding may occur.
2. Do not reverse the cold*hot water pipe. Otherwise,scalding may occur.
3. Do not use steam to supply hot water. Otherwise, scalding may occur.

5
Attentions in construction and maintenance
Attentions
1. As the ceramic cartridge is a precise component, do not dismantle it without
authorization. Otherwise, such poor conditions as water leakage, etc. may be
caused.
2. Do not impact the product. Otherwise, failure, water leakage may occur.
3. With the product design being updated constantly, the physical object may not
coincide with the figure. However, the basic principle for installation, use is the
same.
4. Due to water supply inspection before ex-factory,there may be water remaining
in the faucet.This is not product problem.
Maintenance
To maintain a beautiful appearance of the product, the user is requested
to conduct maintenance and care in the following method.
1. Wipe with a piece of soft cloth frequently and use a piece of soft cloth
dipped in water to wipe from time to time.
2. When dirt exists obviously, please use water to wash sufficiently after
wiping with a neutral detergent.
6
Mixed
Red Blue
Cold
Hot
Water supply center
Close
Open
Recommended Installation distance 150
Upper end-surface
of water basin
Installation completion figure
TLG01310* "GO" Wall Mounted Single Lavatory Faucet (Short)
34
46
76
107
45
47
120
About57。
About57。
8
52
17
G1/2
70±13
192
100
G1/2
(175)
8
(200)
11°
A
b
o
u
t
2
2
。
Note: The unit of the above dimensions mm;
The dimension in ( ) is reference ones.

Finished
wall surface
Finished
wall surface
Hot water
supply pipe
Cold water
supply pipe
Hot water
supply pipe
Cold water
supply pipe
concrete block
8
Faucet installion
7
Knife saw Screw driver
Hex wrench
(opposite side 2.5mm)
Adhesive for
bathroom
Fixing screw
Horizontal Vertical
Waterproof cloth
(2 pieces)
Waterproof adhesive
Tools to be prepared before installation
Confirmation before installation
■ Make sure that the water supply pipe has been shut off and the waterway
has been cleaned.
■ Read the installation manual carefully and follow the installation instruction.
I.Installation the main body
1. Connect the main body of faucet to a matching pipe. Groove the wall
in accordance with the illustrated dimension. Otherwise, it might
cause a problem when mounting the faucet.
※Essential: Calibrate the wall embedded body with a gradienter to
keep its horizontal direction and vertical direction at optimum.
Faucet installion
Installed on the concrete block
As shown in the figure, use cement or other padding to mount the product
in the wall.
As shown in the figure, use screws to fix the product on the wall。
※Please according to the need to further prepare suitable screw.
Installed to the intergration of the bathroom,ect,clapboard and layer board：
MAX
MIN
70±13
17

52
94
(162)
120
5.5
100
MAX
MIN
70±13
17

51
76
(162)
120
5.5
100
4
-
10
Clapboard、
layer board
MAX 60

II. Installations of spout part and handle part
10
Faucet installion
9
Faucet installion
Hex wrench
(opposite side
2.5mm)
Indication cover
Screw
Cartridge
Decoration cover
Handle
Inner sheath
(to be pulled out)
Attentions
●When mounting the wall embedded body, do
not remove the resin sheath or the inner
sheath.
●Pay attention to the embedding depth of the
wall embedded body to ensure that the
finished wall surface is between the marks
MIN and MAX on the protective sheath.
●Connect the inlet pipe to the wall embedded
body. Make sure that each connection does
not leak and then apply cement padding.
Attentions
●Do not hurt the inner sheath when
cutting to avoid damaging the
internal cartridge sheath.
53- 60
100

53- 60
2. Get the waterproof cloth through
the resin sheath and use the
adhesive for bathroom to paste
it onto the cement wall surface.
Resin
sheath
Inner sheath
Cement
wall surface
Waterproof cloth
Adhesive for
bathroom
Finished wall
surface
Ceramic tile opening size（unit:mm）
3. After the adhesive is
completely dried, fix the
tile.(Ceramic tile opening
size below）。In the case
of the resin sheath and the
wall of the gap evenly
coated with waterproof
adhesive,and adhesive
surface can not be convex
the wall.
1. Cut off the resin protective sheath with a
knife saw and ensure that the interval
between the raised edge of the resin
sheath and the wall surface is within
2mm.(The edge shall not sink in the wall
surface)
2. Installation of handle part：
a. Pull out the inner sheath (Note: The inner sheath does not work
anymore after mounting is finished).
b. Cap the cartridge sheath with the decoration cover near the wall
surface.(Note: Apply a small amount of soap water on the O-ring
inside the decoration cover for lubrication in order to facilitate
mounting)
c. Mount the handle onto the cartridge and use the screw to fix it
and mount the indication cover at the position of the screw hole.
Inner sheath
Protective
cover
Within
2mm

Hex wrench
(opposite side 2.5mm)
3. Installation of spout part
a. Insert the fixing connecter into the wall embedded body and use 2
screws to fix it onto the wall.
b. Get the decoration cover through the
fixing connecter. Connect the spout body
to the fixing connecter to attach it closely
to the decoration cover. Align the position
of the decoration cover and the spout
body and then fix the spout body with a
screw.
Faucet installion
11
Screw driver
Fixing connecter
Screw
Screw
Spout body