Toto 0G386RY Operation and maintenance manual

0G386RY[A]
2018.03
使用说明书
使用产品前请仔细阅读本使用说明书，并保留备用。
Instructions for operation
Before using product, read these Instructions for operation
carefully and retain it for future reference.

目录
1 2
明细单
1 2
目 录
目录
明细单
使用条件与使用上的注意
使用上的注意与保养
产品示意图
拆卸与检查
产品保修卡
合格证
1
2-3
4
5
6-9
10-13
14
15
明细单
手柄部
捏手部
套 筒
装饰板
装饰盖
使用说明书
施工说明书
1套
1套
1个
1套
1个
1本
1本
主体部
使用说明书
施工说明书
使用此明细单的产品包括:
DV309-3R 铜合金壁式单柄双控暗装水嘴阀体(可转换)
DV309S 铜合金壁式单柄双控暗装水嘴阀体(可转换)
使用本明细单的产品包括:
DP348 铜合金壁式单柄双控暗装水嘴面板
DP352 铜合金壁式单柄双控暗装水嘴面板
DP352场合无装饰盖
1套
1本
1本

明细单
3 4
明细单
手柄部
装饰板
装饰盖
螺 钉
使用说明书
施工说明书
1套
1套
1个
4个
1本
1本
主体部
使用说明书
施工说明书
使用本明细单的产品包括:
DV311-2R 铜合金壁式单柄双控暗装水嘴阀体
DV311-3 铜合金壁式单柄双控暗装水嘴阀体
使用本明细单的产品包括:
DP349 铜合金壁式单柄双控暗装水嘴面板
DP353 铜合金壁式单柄双控暗装水嘴面板
DP353场合无装饰盖，螺钉2个
1套
1本
1本
使用条件与使用上的注意
使 用 条 件
警告
1.幼儿禁止使用或幼儿需要成年人监护使用、老人和残障人士等特殊
群体应在有行动能力人员陪同下使用。
2.水嘴的供热水一侧处于高温状态，请注意勿使皮肤直接接触五金配
件表面，否则可能会烫伤。
3.请勿配反冷*热水配管，否则可能会烫伤。
4.供热水请勿使用蒸汽，否则可能会烫伤。
5.施工时本产品的G1/2或G3/4内螺纹请勿与R1/2或R3/4接头安装使用，
否则可能会造成主体螺纹处开裂、漏水等不良。
使 用 上 的 注 意
表示如果无视此标志而误操作时，有可能造成人员重伤或死亡。
表示如果无视此标志而误操作时，有可能造成人身伤害或财产损失。
警告
注意
1.供冷水*热水压力：
最低压力…………0.05MPa(流动压)
最高压力…………1.0MPa(静压)
2.花洒配套使用时，建议水压0.2MPa(流动压)以上，否则可能无法充分发挥
花洒的性能。
3.供水温度在4℃～90℃，建议使用温度60±5℃,供热水请勿使用蒸汽。
4.使用环境温度0℃以上。如果低于0℃，水嘴会出现变形、冻裂等现象。
5.为防止花洒内部损坏，花洒侧吐水温度不得超过60℃，建议使用温度45℃
以下。
6.长时间不使用时，可能导致水嘴内部及外部锈蚀不能使用等现象。
7.如果您需要废弃本产品，请勿将其作为一般生活垃圾处理，请依照法规经
由独立的回收体系进行合适的处理、恢复和回收。
8.本说明书中的产品具有清洗功能。

5
使用上的注意与保养
6
产品示意图
为长期保持产品的美观，请用户按以下方法维护保养。
1.经常用软布擦拭，间或用软布蘸水擦拭。
2.当有污垢且比较明显时，请用中性洗涤剂擦拭后充分进行水洗。
保养
注意
1.由于陶瓷阀芯是较精密的部件，请勿擅自分解，否则可能会造成漏
水等不良。
2.配套使用时，建议水压0.2MPa以上，否则可能会无法充分发挥水嘴
的性能。
3.请勿撞击本产品，否则可能会造成故障、漏水。
4.必须使用中性洗涤剂清洗，中性以外的洗涤剂会破坏镀层或使表面
变色。
5.不得使用酸性洗涤剂和去污粉、抛光粉等含粗颗粒的洗涤剂和尼龙
刷，否则可能会破坏镀层等。
6.可使用软布擦拭，间或用机油或车用蜡浸布擦拭，但请勿接触树脂
部件，否则可能失去光泽和产生锈蚀。
7.随着产品式样的不断更新，实物存在与图示不符的情况，但基本安
装、使用原理相同。
DP348 铜合金壁式单柄双控暗装水嘴面板
DV309S 铜合金壁式单柄双控暗装水嘴阀体(可转换)
W.L
DP348
闭
开热水
混合水
冷水
DV309S
蓝色红色

7
产品示意图 产品示意图
8
DP349 铜合金壁式单柄双控暗装水嘴面板
DV311-2R 铜合金壁式单柄双控暗装水嘴阀体
DP352 铜合金壁式单柄双控暗装水嘴面板
DV309-3R 铜合金壁式单柄双控暗装水嘴阀体（可转换）
W.L W.L
DV311-2R DP349 DP352
DV309-3R
闭
闭
热水
混合水
混合水
开
开
冷水
热水
冷水
蓝色红色

产品示意图 拆卸与检查
9 3
DP353 铜合金壁式单柄双控暗装水嘴面板
DV311-3 铜合金壁式单柄双控暗装水嘴阀体
W.L
DP353
DV311-3
闭
混合水
开
冷水
热水
10
DP348、DV309S
现 象
水流量小
漏 水
切替不良
开闭手柄晃动
切替手柄晃动
装饰板晃动
检查项目
6
3、4、5、6
4
1
1
2
安装后万一出现故障，请按以下要领拆卸。
（此图内未拆分的零件，需要拆卸的情况下，请联络售后服务人员进行拆卸)
手柄
捏手
接手
装饰板
（2.是否压紧？)
DP348
DV309S
螺丝钉 固定板
固定套
切替阀
(3.是否充分拧紧？) O型圈、垫片
(4.有无划伤、脏物？)
装饰盖
装饰盖
小螺丝
(1.是否充分拧紧？)
垫片
阀门压
(5.是否充分拧紧？)
阀芯
(6.O型圈、有无划伤、脏物？)
阀体

DV309-3R DV311-2R
DP352
DP349
拆卸与检查 拆卸与检查
11 12
手柄
手柄
捏手
接手
装饰板
（2.是否压紧？) 螺丝钉
螺丝钉
固定板
固定板
固定套
切替阀
(3.是否充分拧紧？)
O型圈、垫片
(4.有无划伤、脏物？)
固定小螺丝
(1.是否充分拧紧？)
小螺丝
(1.是否充分拧紧？)
固定小螺丝
(5.是否充分拧紧？)
阀门压
(6.是否充分拧紧？)
阀门压
(3.是否充分拧紧？)
阀芯
(7.O型圈有无
划伤、脏物？)
阀芯
(4.O型圈有无
划伤、脏物？)
阀体
阀体
DP352、DV309-3R
现 象
水流量小
漏 水
切替不良
开闭手柄晃动
切替手柄晃动
装饰板晃动
检查项目
7
3、4、6、7
3、4
1、5
1
2
安装后万一出现故障，请按以下要领拆卸。
（此图内未拆分的零件，需要拆卸的情况下，请联络售后服务人员进行拆卸)
DP349、DV311-2R
现 象
漏 水
手柄晃动
装饰板晃动
检查项目
3、4
1
2
安装后万一出现故障，请按以下要领拆卸。
（此图内未拆分的零件，需要拆卸的情况下，请联络售后服务人员进行拆卸)
垫片
装饰板
(2.是否压紧？) 装饰盖
表示盖

DV311-3
DP353
手柄
螺丝钉 固定板
固定小螺丝
(3.是否充分拧紧？)
小螺丝
(1.是否充分拧紧？)
阀门压
(4.是否充分拧紧？)
阀芯
(5.O型圈有无
划伤、脏物？)
阀体
装饰板
(2.是否压紧？)
拆卸与检查 拆卸与检查
13 14
DP353、DV311-3
现 象
漏 水
手柄晃动
装饰板晃动
检查项目
4、5
1、3
2
安装后万一出现故障，请按以下要领拆卸。
（此图内未拆分的零件，需要拆卸的情况下，请联络售后服务人员进行拆卸)
用 户
销售安装店
购买日
保修期 自购买日起主体及阀芯保修有效期5年，
其余部件保修期为1年
* 若上栏内容未记全，该产品保修卡将视为无效。因此请用户购买时
对记入内容进行确认。
* 本产品保修卡中的保修项目仅限于产品保修卡中所约束的免费维修
项目进行维修。
* 在保修期间，若产品发生故障(漏水、渗漏)，请用户向销售店或安
装店出示产品保修卡及购买发票、提出修理要求。
1.保修期间，在用户正确按说明书、不干胶等指示，使用本公司产
品的情况下，本公司将对有故障产品进行免费维修。
2.在保修期内发生损坏需得到免费修理时，请持本产品保修卡和购买
发票委托安装店或销售店办理。
3.在保期内，下面所列场合的维修为有偿维修。
①使用不当或私自进行的不当修理及改造所造成的故障及损伤。
②安装施工时的不注意或过失造成的故障及损伤。
③安装后又拆移等原因造成的故障及损伤。
④超出使用范围以外的场合下使用本产品所造成的故障及损伤(如
家庭用商品作为业务上商品使用。)
⑤砂粒或污物等造成的损伤。
⑥由于日常的维护保养不当造成的肮脏、电镀部分生锈等不良。
⑦由于火灾、地震、水灾、雷击及其他天灾、公害、气害（液化
气）、盐害及异常电压、使用指定外的电源(电压、频率)等原因
造成的故障及损伤。
⑧本产品保修卡没指定的场合。
⑨本产品保修卡中用户姓名、销售店、安装店、购买日期未填写的场合。
⑩不能出示购买发票的场合。
4.本产品保修卡仅适用于中国国内。
5.本产品保修卡丢失不补，请顾客妥善保管。
免费维修规定

合格证
1 2
Contents
15 1
800-820-9787
400-820-9787
[phone]
GB 18145-2014
Contents
Contents
Detailed list
Service condition and attentions in use
Attentions in use and maintenance
Product schematic diagram
Removal and Inspection
Product Warranty Card
Conformity Certificate
1
2-3
4
5
6-9
10-13
14
15

Detailed list
2 3
Detailed list
Detailed list
Handle part 1 set
Handle knob part 1 set
Bushing 1 piece
Decorative plate 1 set
Decorative cover 1 piece
Instructions for construction 1 copy
Instructions for operation 1 copy
The products using this detailed list include:
DP348 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DP352 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
Note: In case of DP352,these is no decorative cover.
The products using this detailed list include:
DV309-3R Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body (convertible)
DV309S Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body (convertible)
Detailed list
Handle part 1 set
Decorative plate 1 set
Decorative cover 1 piece
Screw 4 pieces
Instructions for construction 1 copy
Instructions for operation 1 copy
The products using this detailed list include:
DP349 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DP353 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
Note: In case of DP353,these is no decorative cover,screw 2 pieces.
The products using this detailed list include:
DV311-2R Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body
DV311-3 Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body
Body
Instructions for construction
Instructions for operation
1 set
1 copy
1 copy
Body
Instructions for construction
Instructions for operation
1 set
1 copy
1 copy

Attentions in use and maintenance
Maintenance
To maintain a beautiful appearance of the product, the user is requested to
conduct maintenance and care in the following method.
1. Wipe with a piece of soft cloth frequently and use a piece of soft cloth
dipped in water to wipe from time to time.
2. When dirt exists obviously, please use water to wash sufficiently after
wiping with a neutral detergent.
Service condition and attentions in use
Serrice condition
1. Cold water supply*hot water supply pressure
Minimum pressure ………………… 0.05MPa (flow pressure)
Maximum pressure ………………… 1.0MPa (static pressure)
2. When the sprinkler is used as ancillary component,it is advised that the water
pressure should be more than 0.2Mpa,otherwise,the performance of the sprinkler
can not be played fully.
3. The temperature for water supply is 4~90℃. It is suggested to use the water
temperature of 60±5℃. Do not use steam to supply hot water.
4. The ambient temperature for use is above 0℃. If not, the water nozzle may deform
and crack due to freezing.
5. To prevent internal sprinkler damage,the water outlet temperature on the sprinkler
side shall not exceed 60℃.It is suggested to use a temperature below 45℃.
6. Being out of use for a long time may result in internal and external rust to the
water nozzle and being unable to be used.
7. If you want to scrap this product, do not treat it as you do for general domestic
grabage. Please follow relevant statutes to have it treated, recovered and collected
appropriately by an independent recovery system.
8. The product in these instructions has a cleaning function.
Attentions in use
Warning:it means that ignoring this mark and misoperation may cause serious
personal injury and death.
Attention: it means that ignoring this mark and misoperation may cause
personal injury or property loss.
Warning
1.Children are not allowed to use or can use only under the custody of adult. Such
special groups as the aged and disabled should be accompanied by those with
behavioral competence when using it.
2.The hot water supply side of the water nozzle is in a condition of high
temperature. Do not allow skin to contact with the hardware surface directly.
Otherwise,scalding may occur.
3.Do not reverse cold*hot water pipes. Otherwise, scalding may occur.
4.Do not use steam to supply hot water. Otherwise, scalding may occur.
5.In construction, do not install and use the G1/2 or G3/4 internal threads of this
product with R1/2 or R3/4 connector. Otherwise, the main body threads may
crack, resulting in such quality problems as water leakage, etc.
4 5
Attentions
1. As the ceramic cartridge is a precise component, do not dismantle it without
authorization. Otherwise, such poor conditions as water leakage, etc. may be
caused.
2. In supporting use,it is suggested that the water pressure should be above
0.2Mpa.Otherwise,the performance of the water nozzle may not be sufficiently
taken advantage of.
3. Do not impact the product. Otherwise, failure, water leakage may occur.
4. It is imperative to use a neutral detergent in cleaning. Other detergents
than a neutral one may damage the plating coat or make the surface discolor.
5. Do not use any such detergent as acidic detergent and abstergent, polishing
powder, etc. Containing thick particles and nylon brush. Otherwise, the
plating coat may be damaged, etc.
6. It is allowed to use a piece of soft cloth to wipe or use from time to time a piece
of cloth immersed in machine oil or vehicle wax to wipe. However, do not
contact with resin components. Otherwise, they may lose the gloss
and become rusty.
7. With the product design being updated constantly, the physical object may
not coincide with the figure. However, the basic principle for installation, use
is the same.

DV309S W.L
DV311-2R DP349
6 7
Product schematic diagram
DP348 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DV309S Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body (convertible)
Product schematic diagram
W.L
DP348
Open
Open
Close
Close
Hot water Hot water Cold water Cold water
Mixed water Mixed water
DP349 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DV311-2R Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body
BlueRed
BlueRed

Open
Open
Close
Close
Hot water Hot water
Cold water Cold water
Mixed water Mixed water
8 9
Product schematic diagram
DP352 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DV309-3S Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body (convertible)
Product schematic diagram
DP353 Copper alloy wall-mounted type single-handle double-control
concealed water faucet panel
DV311-3 Copper alloy wall-mounted type single-handle double-control
concealed faucet valve body
W.L
DP352
DV309-3R W.L
DP353
DV311-3

Removal and Inspection
10
DP348、DV309S
Phenomenon
The water flower is small
Water leakage
Switching is poor
The opening and closing handle sways
The switching handle sways
The decorative plate sways
Inspecting items
6
3、4、5、6
4
1
1
2
Removal and Inspection
In case of any failure after installation,please remove according to the following
main points.(When any spare part and component not removed in this figure
needs to be removed,please contact with relevant after-sale service personnel)
Handle Handle
Handle knob Handle knob
Receiving hand
Decorative plate
(2.If the decorating
ring is compressed tight?)
Decorative plate
(2.If the decorating
ring is compressed tight?)
Fixing screw
Fixing screw
Fixing plate Fixing plate
Fixing set Fixing set
Switching valve
(3.Sufficently
tightened?)
Switching valve
(3.Sufficently
tightened?)
O-ring Gasket
(4.Any scratch,dirt?)
DV309S
DP348 DP352
DV309-3R
O-ring Gasket
(4.Any scratch,dirt?)
Indicating cover
Small screw
(1.Sufficiently tightened?)
Small screw
(1.Sufficiently tightened?)
Small screw
(5.Sufficiently tightened?)
Gasket
Indicating cover
Valve pressure part
(5.Suffciently tightened?)
Valve pressure part
(6.Sufficiently tightened?)
Ceramic valve core
(6.O-ring Any scratch,dirt?)
Ceramic valve core
(7.O-ring Any scratch,dirt?)
Valve body Valve body
DP352、DV309-3R
Phenomenon
The water flower is small
Water leakage
Switching is poor
The opening and closing handle sways
The switching handle sways
The decorative plate sways
Inspecting items
7
3、4、6、7
3、4
1、5
1
2
In case of any failure after installation,please remove according to the following
main points.(When any spare part and component not removed in this figure
needs to be removed,please contact with relevant after-sale service personnel)
11

DP349 DP353
DV311-2R
DV311-3
Handle Handle
Receiving hand
Decorative plate
(2.If the decorating
ring is compressed tight?)
Decorative plate
(2.If the decorating
ring is compressed tight?)
Fixing screw Fixing plate
Switching valve
(3.Sufficiently
tightened?)
Ceramic valve core
(4.O-ring Any scratch,dirt?)
Ceramic valve core
(5.O-ring Any scratch,dirt?)
Small screw
(1.Sufficiently tightened?)
Gasket
Removal and Inspection
12 13
DP349、DV311-2R
Phenomenon
Water leakage
The handle sways
The decorative plate sways
Inspecting items
3、4
1
2
Removal and Inspection
In case of any failure after installation,please remove according to the following
main points.(When any spare part and component not removed in this figure
needs to be removed,please contact with relevant after-sale service personnel)
Small screw
(1.Sufficiently tightened?)
Valve pressure part
(3.Sufficiently tightened?)
Valve pressure part
(4.Sufficiently tightened?)
Indicating cover
Valve body
Fixing screw
Fixing plate
Indicating cover
Valve body
DP353、DV311-3
Phenomenon
Water leakage
The handle sways
The decorative plate sways
Inspecting items
4、5
1、3
2
In case of any failure after installation,please remove according to the following
main points.(When any spare part and component not removed in this figure
needs to be removed,please contact with relevant after-sale service personnel)

14
Product Warranty Card Comformity Cerificate
15
The valid warranty period for the body and valve
core is 5 years from the date of purchase.
The warranty period for other parts is 1 year.
User
Sales shop or installation shop
Purchasing date
Warranty period
*If the contents in the above column are not recorded completely, the warranty
will be deemed as invalid. Therefore, the users are requested to confirm the
recorded contents when purchasing.
*The warranty items in this warranty are limited to repair to the free repair
items as restricted in it.
*If any failure (water leakage, release) occurs to the product during the
warranty period, the users are requested to show the warranty and purchase
invoice to the sales shop or installation shop and make repair requirements.
1. In the circumstance that the users use correctly the product of our company
according to the instructions on the instruction book, sticker, etc. during the
warranty period, the company will provide free repair to any faulty product.
2. When any free repair is required due to any damage during the warranty
period,please hold this warranty and purchase invoice to entrust the
installation shop or sales shop for handling.
3. The repairs listed below are paid repairs during the warranty period.
1) Any failure and damage resulting from improper use or unauthorized
improper repair and modification.
2) Any failure and damage due to failure to pay attention or mistake in
installation construction.
3) Any failure and damage due to removal for relocation, etc. after installation.
4) Any failure and damage due to use of this product under such occasions
as being beyond the range of use (for example, commodity for home use
serves as commodity for business use.)
5) Any damage resulting from sand or dirt, etc.
6) Any poor condition such as dirty, plating rust, etc. due to improper daily
maintenance and care.
7) Any failure and damage due to fire, earthquake, flood, lightning strike and
other act of God, public nuisance, gas nuisance (liquefied gas), salt
nuisance and abnormal voltage, use of other power sources than that
designated (voltage, frequency), etc.
8) Other occasions not indicated in this warranty.
9) The occasion where user name, sales shop, installation shop and
purchase date are not filled out in this warranty.
10) The occasion where no purchase invoice can be shown.
4. This warranty only applies to China.
5. This warranty will not be reissued in case of loss. Customers are requested
to preserve it properly.
Free Repair Regulations
This product is judged as satisfactory in inspection.
Applicable standard: GB 18145-2014
Product Model No.: See the label on the packaging case
Product name: See the label on the packaging case
Production date: See the label on the packaging case
Assembly factory: TOTO (Dalian) Co., Ltd.
Telephone: [phone]
Factory address: 17 Dong Bei Second Street,Economic&Technical Development
zone,Dalian
TOTO(China)Co.,Ltd.
After-sale service toll free telephone all over the country:
800-820-9787(fixed telephone)
400-820-9787(for mobile phone users)
Vendor:TOTO(China)Co.,Ltd.
Address:Room 1915,North Building of Beijing Jiali Center,No.1,
Guanghua Road,Chaoyang District,Beijing
Website:www.toto.com.cn