Touch Dynamic Jupiter PC User manual

USER MANUAL
Jupiter PC
VERSION 1.3 JANUARY 2011

ii
Copyright 2011
All Rights Reserved
Manual Version 1.3
Part Number:
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced
or translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
To disconnect the machine from the electrical power supply, turn off the power1.
switch and remove the power cord plug from the wall socket. The wall socket must
be easily accessible and in close proximity to the machine.
Read these instructions carefully. Save these instructions for future reference.2.
Follow all warnings and instructions marked on the product.3.
Do not use this product near water.4.
Do not place this product on an unstable cart, stand, or table. The product may fall,5.
causing serious damage to the product.
Slots and openings in the cabinet and the back or bottom are provided for6.
ventilation to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or heat
register or in a built-in installation unless proper ventilation is provided.
This product should be operated from the type of power indicated on the marking7.
label. If you are not sure of the type of power available, consult your dealer or local
power company.
Do not allow anything to rest on the power cord. Do not locate this product where8.
persons will walk on the cord.
Never push objects of any kind into this product through cabinet slots as they9.
may touch dangerous voltage points or short out parts that could result in a re or
electric shock. Never spill liquid of any kind on the product.

iii
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC with
regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used
battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S)
related legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure”
compliant.
4.7.3.2Materialsforreenclosures
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material
of a FIRE ENCLOSURE, in the thinnest signi cant wall thickness used, shall be of
V-1 CLASS MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all
STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest
signi cant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the
test of Clause A.1

iv
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed
of with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

v
Revision History
Changes to the original user manual are listed below:
Revision Description Date
1.0 Initial release•2009 March
1.1 B68 motherboard added•
Jumper setting updated•2009 December
1.2
C48 motherboard added•
Specication updated•
B68, B98 Jumper Setting updated•
Safety message updated•
Cash Drawer Controller Register updated•
2010 October
1.3 Model name changed•
C48 motherboard updated to V2.1•2011 January

vi
Table of Contents
1. PackingList.............................. 1
1-1. Standard Accessories..............................................1
1-2. Optional Accessories ...............................................1
2. System View ............................. 2
2-1. Front and Side View ................................................2
2-2. I/O view....................................................................3
2-3. Dimensions..............................................................3
3. ComponentsReplacing........... 4
3-1. RAM Module Replacing...........................................4
3-2. HDD Replacing........................................................5
3-3. pSSD Card Module Replacing.................................5
3-4. Wall-mount module installing...................................6
3-5. Power Adapter Replacing ........................................7
3-6. Wireless LAN Installing............................................8
3-7. Cash Drawer Installing ............................................9
4. Specication ........................... 11

vii
5. JumperSetting........................ 13
5-1. For C48 Motherboard .............................................13
5-1-1. Motherboard Layout ................................................ 13
5-1-2. Connectors & Functions .......................................... 14
5-1-3. Jumper Setting ........................................................ 15
5-2. For B68 Motherboard .............................................18
5-2-1. Motherboard Layout ................................................ 18
5-2-2. Connectors & Functions .......................................... 19
5-2-3. Jumper Setting ........................................................ 21
5-3. For B98 Motherboard .............................................23
5-3-1. Motherboard Layout ................................................ 23
5-3-2. Connectors & Functions .......................................... 24
5-3-3. Jumper Setting ........................................................ 25
Appendix: Drivers Installation .... 27

1
PackingList1.
StandardAccessories
1-1.
OptionalAccessories
1-2.
System boxa.
Power Cordb.
RJ45 to DB9 cablec.
Driver bankd.
WLAN Card + internal antennaa.
pSSD card moduleb.
pSSD Card
a
a
b
b
d
c

2
System View2.
Front and Side View
2-1.
Power adapter holding bracket1.
HDD Door2.
I/O Placement3.
External antennas (Options) (installing for either one)4.
Ventilation holes5.
VESA and wall-mount mounting holes6.
2
3
4
56
1

3
I/O view
2-2.
Dimensions
2-3.
Item No. Description
a DC Jack
b LAN Port
c Cash Drawer Port
d MIC-in
e Line-Out
f COM Port 1, 2, 3, 4 (from left to right)
g USB x 4
h Parellel Port
i Power Button
j Power LED Indicator
k PS/2
l VGA Port
abcde
fgh
i
k
j
185mm
l
70.3mm
62.3mm
335mm

4
ComponentsReplacing3.
RAMModuleReplacing
3-1.
RemovingaRAMmodule
Use both fingers to pull the ejector clips out of the sides of the module.1.
Slide out to remove the memory module from the memory slot.2.
InstallingaRAMmodule
Slide the memory module into the memory slot and press down until the ejector clips1.
click in place.
Please unfasten the screws (x3) and gently flip up the rear cover to access the
motherboard rst, please refer to the motherboard layout to nd the RAM module place.

5
HDDReplacing
3-2.
Open the HDD door by unfastening the screw (x1).1.
Disconnect the HDD connectors (x2) and replace the hard drive disk.2.
If your system is equipped with HDD as storage device, please replace it as
following steps.
pSSDCardModuleReplacing
3-3.
If your system is equipped with a pSSD card as storage device, please replace it
as following steps.
Please unfasten the screws (x3) and1. gently flip up the top cover.

6
Turn the inside out and disconnect the SATA cable.2.
Unscrew the screws (x2) to remove and replace the pSSD card from the3.
inside of the top cover.
Wall-mountmoduleinstalling
3-4.
You can assemble the system box with your wall-mount bracket, please refer to
the steps below.
You can assemble the system box with your wall-mount bracket, please refer to
the steps below.
There are 8 holes at both sides (4 with tear-drop shaped holes and 4 with1.
circle shaped holes) for securing your own wall-mount bracket or screws to fix
the system box onto the wall.

7
Disconnect the power cord from the adapter and the I/O panel.1.
PowerAdapterReplacing
3-5.
The system is equipped with a 90W power adapter that is held securely in a
power holding bracket. Please replace the power adapter as below steps.
Slide the power adapter out of the holding bracket.2.

8
WirelessLANInstalling
3-6.
If you install the wireless LAN module after manufacturer, please buy wireless
LAN module with external antenna from your local distributor or dealer.
The installation procedure is slightly different depending on which motherboard
your system is equipped with. Please refer the location of motherboard layout on
Chapter.
To external antenna
For B68/C48 Motherboard
To external antenna
For B98 Motherboard
Please open the rear cover first. (See Chapter 3-1).1.
Press-out the blind hole on the enclosure before starting to assemble the2.
external antenna and the antenna coaxial cable.
Assemble the coaxial cable, nut, washer and the external cable as above3.
picture instructs.
For B68/C48 motherboard:4. Insert the WLAN card into the mPCI-e slot on
the motherboard. Press down the WLAN card and fix it to the motherboard by
fastening the screw (x1) provided.
For B98 motherboard: Insert the WLAN card into the mPCI slot until the
ejector clips lock it in place.
Connect the other end of the antenna coaxial cable to the “Main” connector5.
on the WLAN card.

9
CashDrawerInstalling
3-7.
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
CashDrawerPinAssignment
Pin Signal
1 GND
2 DOUT bit0
3 DIN bit0
4 12V / 19V
5 DOUT bit1
6 GND
CashDrawerControllerRegister
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
RegisterLocation: 48Ch
Attribute: Read / Write
Size: 8bit
BIT BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Attribute Reserved Read Reserved Write Reserved
76543210
XX X X X
Reserved
Cash Drawer “DOUT bit0” pin output control
Cash Drawer “DOUT bit1” pin output control
Reserved
Cash Drawer “DIN bit0” pin input status
Reserved
1
6

10
Bit 7: Reserved
Bit 6: Cash Drawer “DIN bit0” pin input status.
= 1: the Cash Drawer closed or no Cash Drawer
= 0: the Cash Drawer opened
Bit 5: Reserved
Bit 4: Reserved
Bit 3: Cash Drawer “DOUT bit1” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 2: Cash Drawer “DOUT bit0” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 1: Reserved
Bit 0: Reserved
Note: Please follow the Cash Drawer control signal design to control the Cash
Drawer.
Cash Drawer Control Command Example
Use Debug.EXE program under DOS or Windows98
Command Cash Drawer
O 48C 04 Opening
O 48C 00 Allow to close
Set the I/O address 48Ch bit2 =1 for opening Cash Drawer by “DOUT bit0” pin►
control.
Set the I/O address 48Ch bit2 = 0 for allow close Cash Drawer.►
Command Cash Drawer
I 48C Check status
The I/O address 48Ch bit6 =1 mean the Cash Drawer is opened or not exist.►
The I/O address 48Ch bit6 =0 mean the Cash Drawer is closed.►

11
Specication4.
Mainboard C48 B68 B98
CPU
Intel Pineview D525
dual core 1.8G L2 1M,
FSB800Mhz
Intel® AtomTM N270
Processor 1.6GHz L2
512K FSB 533MHz
Intel® Celeron® M 1.86G,
CoreTM 2 Duo 1.66G,
CoreTM Duo 2.0G
Chipset CPU with Graphic built-in +
ICH 8M Intel® 945GSE + ICH 7M Intel® 945GME + ICH 7M
System Memory 2 x DDR3 DIMM up to
4GB, FSB 800Mhz
2 x DDR2 DIMM up to
2GB FSB 533MHz
2 x DDR2 DIMM
socket up to 4GB FSB
400/533/667MHz
Graphic Memory Intel GMA 3150 share
system memory up to
256MB
Intel GMA 950 share system memory up to 224MB
BIOS AMI AWARD PnP
Storage Device
Hard Drive 2.5" SATA HDD bay
Flash Memory pSSD™ Modular Solid State Drive (optional)
Compact Flash Card (optional)
Expansion
Mini PCI Socket N/A 1
Mini PCI-E Socket 1 N/A
I/O Ports
USB Port 4 x USB 2.0
Serial / COM 4 x RJ 45 COM
(COM1/COM2 standard
RS-232 without power,
COM3 /COM4 powered
COM with power enable /
disable by BIOS setting and
+5V/+12V by MB setting.
COM3 default +5V/ COM4
default +12V )
4 x COM ports RJ-45 connectors
( COM1 & COM2 standard RS-232; COM3 & COM4
pin9 with 5V /12V power by jumper )
Parallel 1
LAN Port 1 x RJ-45 (10/100/1000Mbps Giga LAN)
VGA 1
Cash Drawer Port 1 (12V / 24V)
MIC-in 1
Line-out 1
DC Jack 1
Power Button 1
LED indicators
Power LED 1

12
Mainboard C48 B68 B98
Power 19V /90W ext. power adapter
Certicate
EMC & Safety FCC / CE Class A, LVD, UL
Environment
Operating
Temperature 5°C ~ 35°C (41°F ~ 95°F)
Storage
Temperature -20°C ~ 55°C (-4°F ~ 140°F)
Operating Humidity 20% ~ 80% RH non-condensing
Storage Humidity 20% ~ 85% RH non-condensing
Communication
Wireless LAN 802.11 b/g/n wireless LAN card
System color Black
Dimensions
(W x D x H) 335 x 185 x 70.3 mm (13.2" x 7.3" x 2.8")
Weight
(N.W./G.W.) 3kgs / 3.5kgs
OS Supported Windows® XP Professional, Windows Embedded POSReady 2009, WePOS,
Windows XP Professional for Embedded, Windows 7, Linux
* This specication is subject to change without prior notice.

13
For C48 Motherboard
5-1.
JumperSetting5.
Motherboard Layout
5-1-1.