Touch Dynamic CS-200 User manual

CS-200
Point-of-Sale
HardwareSystem
User Manual
Revision v1.3 December 2009

2
Copyright 2007 Oct. ~
All Rights Reserved
Manual Version 1.3
Part Number:
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose. We shall not be
liable for errors contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are
reserved. No part of this document may be photocopied, reproduced or translated to another
language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft® and
Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.

3
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation to
ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register or in a built-in installation unless
proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive
2004/108/EC with regard to “Electromagnetic compatibility” and
2006/95/EC “Low Voltage Directive”.
FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.

4
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with the
same or equivalent type recommended by the manufacturer. Discard used batteries
according to the manufacturer’s instructions.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection,
recycling and disposal of electric and electronic devices and their components.
The crossed dustbin symbol on the device means that it should not be disposed of with other
household wastes at the end of its working life. Instead, the device should be taken to the
waste collection centers for activation of the treatment, collection, recycling and disposal
procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal.

5
Revision History
Changes to the original user manual are listed below:
Version Date Description
1.0 2007 December Initial release
1.1 2007 March System disassembly updated
1.2 2007 October
Cover page update
Wall mount bracket installation
Connector Pin Definition update
1.3 2009 December Drivers installation removed from manual

6
Table of Contents
1. Item Checklist .............................................................................................................................................................7
1.1 Standard Items......................................................................................................... 7
2. System View.................................................................................................................................................................8
2.1 Front View................................................................................................................ 8
2.2 Rear View................................................................................................................. 8
2.3 System Drawing....................................................................................................... 9
4. Peripherals Installation............................................................................................................................................11
4.1 Biometric Magnetic Stripe Reader Installation.........................................................11
4.2 Cash Drawer Installation.........................................................................................11
4.3 Customer Display Installation................................................................................. 13
4.4 Second Display Installation.................................................................................... 14
4.5 Wall Mount Bracket Installation.............................................................................. 15
5. System Disassembly..................................................................................................................................................16
5.1. Removing the Base Cover .................................................................................... 16
5.2. Replacing the HDD ............................................................................................... 17
5.4. Replacing the Power Supply................................................................................. 17
5.5. Replacing the RAM............................................................................................... 18
Appendix A: Specification............................................................................................................................................19
Appendix B: Jumper Settings......................................................................................................................................21
Appendix C: BIOS Setting...........................................................................................................................................27
Appendix D: Drivers Installation................................................................................................................................30

7
1. Item Checklist
Take the system unit out of the carton. Remove the unit from the carton by holding it by
the foam inserts. The following contents should be found in the carton:
1.1 Standard Items
a. Driver CD
b. Power Cable
Note: The power cord type various according to different country and region.

8
2. System View
2.1 Front View
2.2 Rear View
Note: The maximum current that can be drawn from each COM port is 500 mA.
CD-ROM
(option) USB 1 & 2 Power Button
VGA
COM3
KB/Mouse LAN
Cash Drawer
Power USB 24V
Power USB 12V
COM2
COM1
LPT COM4 Line-In Line-Out

9
2.3 System Drawing
Item Description
1 Front Bezel
2 Touch Panel
3 LCD Panel
4 LCD Chassis
5 Main Board
6 Inverter
7 MSR Function Board
8 Touch Bridge Board
9 Thermal Module
10 LCD Cover Assembly
11 MSR Dummy Door
12 CPU / RAM Door

10
Item Description
13 CD-ROM
14 Base Front Cover
15 Front I/O Board
16 CD-ROM Guide Bracket
17 Side Cover
18 Power Supply
19 Rear I/O Board
20 Base Cover Bracket
21 Base Cover

11
4. Peripherals Installation
4.1 Biometric Magnetic Stripe Reader Installation
a. Plug-in the cables (2) into the connectors on
the terminal.
b. Secure the screws (3) to stabilize the
module to the terminal.
4.2 Cash Drawer Installation
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
4.2.1 Cash Drawer Pin Assignment
4.2.2 Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
The Cash Drawer Control Register and the Cash Drawer Status Register.
Register Location: 4B8h
Attribute: Read / Write
Size: 8bit
6 1
Pin Signal
1 GND
2 DOUT bit0
3 DIN bit0
4 12V / 24V
5 DOUT bit1
6 GND

12
BIT BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Attribute Reserved Reserved Reserved Read Reserved Reserved Write Write
7 6 5 4 3 2 1 0
X X X X X
Cash Drawer “DOUT bit0” pin output control
Cash Drawer “DOUT bit1” pin output control
Reserved
Cash Drawer “DIN bit0” pin input status
Reserved
Bit 7: Reserved.
Bit 6: Reserved.
Bit 5: Reserved.
Bit 4: Cash Drawer “DIN bit0” pin input status.
= 1: the Cash Drawer closed or no Cash Drawer.
= 0: the Cash Drawer opened.
Bit 3: Reserved.
Bit 2: Reserved.
Bit 1: Cash Drawer “DOUT bit1” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow closing the Cash Drawer
Bit 0: Cash Drawer “DOUT bit0” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow closing the Cash Drawer
Note: Please follow the Cash Drawer control signal design to control the Cash Drawer.
4.2.3 Cash Drawer Control Command Example
Use Debug.EXE program under DOS or Windows98
Command Cash Drawer
O 4B8 01 Opening
O 4B8 00 Allow to closing
Set the I/O address 4B8h bit0 =1 for opening the Cash Drawer by “DOUT bit0” pin
control.
Set the I/O address 4B8h bit0 = 0 to allow closing Cash Drawer.
Command Cash Drawer
I 4B8 Check status
The I/O address 4B8h bit4 =1 means the Cash Drawer is closed or no Cash Drawer.
The I/O address 4B8h bit4 =0 means the Cash Drawer is open.

13
4.3 Customer Display Installation
a. Pass the cable through the hole. b. Pass the cable through the pole.
Place the short or long pole into the
hole.
c. Tighten the screws (2) under the pole. d. Connect the cable. Please setup the
COM port power.
e. Connect the cable into the display. f. Tighten the screws as shown in the
picture.

14
4.4 Second Display Installation
Please switch off the system power before connecting the second display.
a. Connect the VGAcable (male)
into the second display.
b. Mount the second display on the
rear of the system and tighten the
screws (3) on the supporter (All
these screws are behind the
supporting pole).
c. Connect the other end of the
VGA cable (female) into the
system.

15
4.5 Wall Mount Bracket Installation
a. Place the wall mount bracket into the
hooks and slide the bracket to the
direction as shown by the arrows
b. The bracket should be located
properly as shown by the photo.
c. Tighten the screws (2) (one on each
side) to finish the installation.

16
5. System Disassembly
5.1. Removing the Base Cover
a. Release the thumbscrews (2). b. Slide the top cover towards the back and
remove it.
c. Release the thumbscrews (2). d. Pull the base cover bracket towards you
by the handle, and lift it up.
e. Fix the base cover in the open position
as shown in the picture.

17
5.2. Replacing the HDD
To replace the HDD, please first follow the steps in chapter 5.1.
a. Disconnect the IDE cable (1) and power
cable (1). b. Remove the screws (4) to replace the HDD.
5.4. Replacing the Power Supply
a. Remove the screws (2). b. Disconnect the 20pin cable (1).
c. Remove the screw (1). d. Remove the screws (2).
You can now remove the power supply.

18
5.5. Replacing the RAM
a. Remove the screws (2). b. Lift the cover up and remove it.
c. The memory slots are located on the
mainboard. To remove the memory
module, use your finger to push the
DIMM slot ejector clips into the down
position.
d. Remove the memory module from the
slot.

19
Appendix A: Specification
Main board B82
CPU Support Intel SK478 CPU Up to P4 2.8G, Celeron 2.0/2.5G, Mobile
Celeron 1.2G
Chipset Intel 852GME&ICH4 FSB 400/ 533Mhz(selectable by jumper)
System Memory 2 x DDR DIMM sockets supported with memory size up to
2GB
Graphic Memory UMA Share Memory up to 64MB
LCD Touch Panel
LCD Size 12.1” TFT 15” TFT
Brightness 200cd/㎡250cd/㎡
Maximal Resolution 800 x 600 1024 x 768
Touch Screen Type Resistive
Tilt Angle (Degree) 0°~70°
Storage
HDD 1 x 3.5” Drive Bay
ODD 1 x Slim CD-ROM / CD-RW / CD-ROM (optional)
Flash Memory Compact Flash (Type I & II)
Expansion
Mini-PCI Socket 1
External I/O Ports
Front I/O: Line in, Line out (optional)
USB 2 (V2.0)
Rear I/O
PS/2 Keyboard 1
PS/2 Mouse 1
USB 2 (V2.0)
Powered USB 2 (12V / 24V)
Serial / COM 4 x powered COM ports (pin 1/ pin 9 support +5V / +12V by
Jumper)
Parallel 1
LAN (10 / 100) 1 (RJ45)
2
nd VGA Output 1 male type connector with power
Cash Drawer Port 1 x RJ11 (with 12V / 24V)
Audio Jack Line-in, line-out (option)
Internal Speaker 2 x 2W
Internal Interface
USB USB 5 / 6
COM COM5 for touch
2
nd VGA 1 x 10pin header

20
Control / Indicator
Power Button 1
Indicator LED 2 (Power, HDD)
Power
Power Supply Internal 180W ATX switching mode power supply
Environment
EMC & Safety FCC Class A, CE, LVD
Operating Temperature 5℃~ 35℃(41℉~ 95℉)
Storage Temperature -20℃~ 60℃(-4℉~ 140℉)
Operating Humidity 20% ~ 80% RH non condensing
Storage Humidity 20% ~ 85% RH non condensing
Peripherals
Input Device
Magnetic Card Reader 3 Tracks (PS2 Interface)
Magnetic Card Reader
+ Finger print module 3 Tracks (PS2 Interface) USB interface
Mini-PCI Wireless Lan
card +
Antenna( optional)
IEEE802.11a/b/g
Output Device
Second Display 12.1” TFT LCD
Customer Display VFD / LCD
Dimension (W x D x H) CP200: 378 x 364 x 358 mm / 14.9” x 14.3” x 14.1”