ZKTeco PA22 User manual

PA22
Version: 1.0
Quick Start Guide
Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.

Side
Bottom
Back Plate
Reset Button
Speaker
USBSlot
Front
Back
2.4InchTFTLCD
Keypad&
RFCardArea
LEDIndicator
Near-infraredPalm
RecognitionSensor
Tamper switch
Terminal Block
Wiring Hole
Mounting Hole
1
Device Overview

2
6.29"
(159.8mm)
4.97"
(126.1mm)
3.18"
(80.7mm)
0.76"
(19.4mm)
1.61"
(41.0mm)
47.24"
(1.2m)
Baseline
1
2
124
3
Install on the Wall
(56.1mm)
2.21"
Device Dimensions
Device Installation
Attach the mounting template sticker to the wall, and drill the holes according
to the mounting paper.
Fix the back plate on the wall with using wall mounting screws.
Attach the device to the back plate from top to bottom.
Fasten the device to the back plate with a security screw.
1.
2.
3.
4.

3
485B
485A
GND
TXD
RXD
GND
WD1
WD0
RS485B
RJ45-1
RJ45-2
RJ45-3
RJ45-6
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
BEEP
GLED
RLED
IWD1
IWD0
GND
12VOUT
BEEP
Green LED
Red LED
GND
+12V
Ethernet
RS232
Lock
Power Out
Sensor
Button
Power In
Auxiliary
In
Bell
Alarm
Wiegand
Out
Wiegand
In
8 Pin Cable Connectors
7 Pin Cable Connectors
4 Pin Cable Connectors
12 Pin Cable Connectors
2 Pin Cable Connectors
Terminal Block

4
Standalone Installation
Alarm
Bell
Lock
TCP/ IP
Exit Button
Door Sensor
ALARM
Wireless Router

5
GND
+12V DC
12V DC Adaptor
Power Connection
Without UPS
GND
+12V DC
With UPS (Optional)
12V±10%, at least 3000MA.
Use an AC adapter with a higher current ratings to share the power with other
devices.
Recommended Power Supply:

Ethernet Connection
LAN Connection
Network Cable Adaptor
1
2
3
4
5
6
7
8
1
4
RJ45-1
RJ45-2
RJ45-3
RJ45-6
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
Door Sensor, Exit Button, Alarm & Bell Connection
Door Sensor
Bell
Alarm
Exit Button
12V DC Adaptor
+12V DCGND
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
1
12
6
Connect the device and the software over an Ethernet cable. An example is
shown below:
Click [Comm.] > [Ethernet] > [IP Address], input the IP address and click
[M/OK].
Note: In LAN, the IP addresses of the server (PC) and the device must be in the
same network segment when connecting to ZKBio Access IVS software.

7
Lock Relay Connection
12V DC Adaptor
Magnetic Lock
+12V DC GND
FR107
Device Not Sharing Power with the Lock
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
DO NOT REVERSE
THE CONNECTION.
V- V+
NC NO COM
Magnetic Lock
FR107
Device Sharing Power with the Lock
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
V- V+
NC NO COM
AC Adapter
DC 12V, 3A
GND
+12V
1
2
DO NOT REVERSE
THE CONNECTION.
The system supports both Normally Opened Lock and Normally Closed Lock. The
NO Lock (Normally Opened when powered) is connected with “NO” and “COM”
terminals, and the NC Lock (Normally Closed when powered) is connected with
“NC” and “COM” terminals. The power can be shared with the lock or can be used
separately for the lock, as shown in the example with NC Lock below:
1
12
1
12

8
RS485 Connection
RS485 Fingerprint Reader Connection
RS485 Fingerprint Reader
DIP Settings
485- 485+ GND +12V GND
Distance:
more than 200 meters
1
8
485B
485A
GND
TXD
RXD
GND
WD1
WD0
12V DC Adaptor
There are six DIP switches which are located on the back of RS485 ngerprint
reader: switches 1 to 4 are for RS485 address, switch 5 is reserved, switch 6 is for
noise reduction on long RS485 cable.
If the RS485 ngerprint reader is powered from the terminal, the length of
wire should be less than 100 meters or 330 feet.
The number 6 switch should be turned on if the cable length exceeds 200
metres or 600 feet as shown below.
1.
2.
3.

9
Wiegand Output Connection
Controller
?
READER 1
BEEP GLED WD1 WD0 GND +12V
485B
485A
GND
TXD
RXD
GND
WD1
WD0
Wiegand Input Connection
BEEP
GLED
RLED
IWD1
IWD0
GND
12VOUT
1
7
Wiegand Reader
BEEP
GLED
RLED
DATA1
DATA0
GND
+12V
AC Adapter
DC 12V, 3A
GND
+12V
1
8
1
2

Device Operation
User Registration
10
When there is no super administrator set in the device, click [M/OK]to enter the
menu. Add a new user and set their User Rule to Super Admin, then the system
will ask for the administrator’s approval before allowing them to access the menu.
For security reasons, we highly recommend that you register a super administrator
promptly.
Click [M/OK]> [User Mgt.]> [New User]to register a new user. The options
includes entering the User ID and Name, setting User Role, registering Palm, Card
Number, Password, and setting Access Control Role.
The following takes the registered palm as an example.
Note: While registering, please keep the yellow circle at the bullseye position as
much as possible.

Click [M/OK] > [COMM.] > [Ethernet] to set the network parameters. If the
TCP/IP communication of the device is successful, the icon will be displayed in
the upper right corner of the standby interface.
Click [M/OK] > [COMM.] > [Cloud Server Setting] to set the server address and
server port, i.e., the IP address and port number of the server after the
software is installed. If the device communicates with the server successfully, the
icon will be displayed in the upper right corner of the standby interface.
Ethernet and Cloud Server Settings
Wireless Network Settings
To congure the Wi-Fi, click [M/OK]> [COMM.] > [Wireless Network].
When the Wi-Fi connection is enabled, select the searched network. Enter the
password, and click [Connect to WIFI (OK)]. The connection is established, with
Wi-Fi icon displayed on the status bar.
11

Access Control Setting
12
Click [M/OK] > [Access Control] to enter the access control management
interface and set relevant parameters for the access control.

Attendance Record
13
Click [M/OK] > [Attendance Search] > [Attendance Record] to enter the
records query interface, input the user ID and select the time range. The
corresponding attendance logs will then be displayed.

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright ©2023 ZKTECO CO., LTD. All Rights Reserved.