Toyotomi 17314780 User manual

WiFi MODULE INSTALLATION

MANUAL

PART #17314780 WiFi module

GB WiFi MODULE INSTALLATION MANUAL ·························································································· PAGE 1

(The installation of this WiFi module must be conducted by qualiﬁed dealer / installer.)

DE INSTALLATIONANLEITUNG WLAN-MODUL ····················································································· PAGE 16

(Die Installation dieses WLAN-Moduls muss durch einen qualiﬁzierten Händler/Installateur vorgenommen werden.)

FR MANUEL D’INSTALLATION DU MODULE WiFi ················································································· PAGE 31

(L’installation de ce module WiFi doit être effectuée par un revendeur/installateur qualiﬁé.)

NL INSTALLATIEHANDLEIDING WiFi-MODULE ····················································································· PAGE 46

(De installatie van deze WiFi-module moet worden uitgevoerd door een erkende verdeler/installateur.)

ES MANUAL DE INSTALACIÓN DEL MÓDULO WiFi ·············································································· PAGE 61

(La instalación de este módulo WiFi deberá ser realizada por un distribuidor/instalador caliﬁcado.)

DK INSTALLATIONSMANUAL TIL WiFi-MODUL ····················································································· PAGE 76

(Installationen af dette WiFi-modul skal udføres af en kvaliﬁceret forhandler/installatør.)

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE

WiFi FUNCTION”. (P.7)

Model FF-95 INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Remove 2 screws on the main circuit board

bracket.

Model FF-55T INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Remove 2 screws on the main circuit board

bracket.

Model FF-55T INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

6. Insert the lead wire into the connector of the

main circuit board.

①

②

Pull out the main circuit board bracket.

Insert the lead wire into the WiFi connector of

the main circuit board.

7. Install the main cuicuit board bracket.

Insert the two claws on the main circuit board

bracket into the slits on the heat shield and

return the main circuit board to their original

positions.

Tighten the main circuit board bracket with two

screws.

8. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-55T INSTALLATION OF WiFi MODULE

①

②

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-55 INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-55 INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-V30T INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-V30 INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

1. Unplug the power supply cord.

2. Remove two screws for the front panel.

3. Place the front panel next to the heater.

NOTE: Be careful not to disconnect the ribbon

cable.

4. Install the WiFi module into the 2 holes on the

PCB support.

5. Insert the lead wire into the WiFi connector of the

main circuit board.

6. Fit the front panel and tighten the two screws.

Proceed to “CONNECT AND USE THE WiFi

FUNCTION”. (P.7)

Model FF-V30 INSTALLATION OF WiFi MODULE

CAUTION: Be sure to turn off and disconnect heater before installation.

CAUTION: Allow heater to cool completely before installation.

Ribbon cable

NOTE: The power button needs to be turned off in order to setup WiFi.

NOTE: The app specifications are subject to change with or without notice.

1. On the smart phone download and install the application “Smart Life”.

2. Register Account: The first time you use the “Smart Life” application you will need to register an account.

i. Accept the "User agreement and Privacy Policy" and press "Agree"

ii. Press “Sign Up”.

iii. Enter your email address and press “Get Verification Code”.

iv. Enter the verification code that was sent to the email address.

v. Set password and press “Done” to finish registration. You will be logged in to the app.

i. ii. iii.

iv. v

CONNECT AND USE THE WiFi FUNCTION

3. Add a new device:

then select the type of device.

Press “Add Device” or “+” symbol in the upper right corner,

The device must be connected to a WiFi network.

Note: “Auto Scan” cannot used.

Device select from QR code

i. Press “–” symbol in the upper right corner.

Activate camera function on the phone.

ii. Read the QR code.

iii. Press “Add”.

ii.

i. iii.

Device select manually

ii. Then select “Heater (Wi-Fi)”

i. Select “Small Home Ap...”

ii.

4. On the heater, turn the heater off first, then press and hold the SET button for

5 seconds.

The WiFi lamp should *blinks at a range of about 2 times per second.

*It could take about 10 seconds to start to blink of the releasing button.

If press and hold the SET button again for 5 seconds, WiFi lamp blinks

approximately once every 3 seconds.

Device select from QR code

i. Select the WiFi connection network, enter its password and press “Next”.

ii. Press “Confirm indicator rapidly blink”.

iii. Indicate the select screen of “Blink Slowly” and “Blink Quickly”.

i. ii. iii.

a. EZ mode (WiFi lamp blinks approximately 2 times per second):

i. Press “Blink Quickly”.

ii. The heater will automatically connect to the WiFi network.

If the connection was successful, you can rename the device.

iii. Press “+” symbol.

iv. Press “Done” in the upper right corner.

i. ii. iii. iv.

Table of contents

Languages:

Popular Control Unit manuals by other brands

Seitz

Seitz 14A80 user manual

Wilo

Wilo RS485 Installation and operating instructions

Becker

Becker CentralControl CC41 Commissioning Instruction

SICK

SICK CDB650 operating instructions

Panduit

Panduit NetKey NKP5E88M Series installation instructions

MX Options Concentric Petite Fitting instructions

Clean Water Systems

Clean Water Systems Fleck 2510 Installation & start?up guide

Fairchild

Fairchild FSB44104A user guide

LEGRAND

LEGRAND Wattstopper LMIN-104 installation instructions

PMK

PMK ATT10BNCS instruction manual

Tektronix

Tektronix TDS3FFT user manual

Woodward

Woodward easYgen Technical manual

Balluff

Balluff BNI EIP-502-105-R015 user guide

NXP Semiconductors

NXP Semiconductors TWR-LS1021A Getting started

Advantech

Advantech PCM-3117 Startup manual

Danfoss

Danfoss MCO 101 manual

Moons'

Moons' Lin Engineering R701P user manual

Aventics

Aventics RV1 operating instructions