TP-Link RE380D User manual

19100112
RE
1910011476
REV 1.0.0

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is
a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other
brands and product names are trademarks or registered trademarks of their
respective holders.
No part of the specifications may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation,
or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Copyright ©2015 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energyand, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
●Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: The manufacturer is not responsible for any radio or tv interference
caused by unauthorized modifications to this equipment.Such modifications
could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna must not be co-
located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is
applicable to only Mobile Configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.”
The device operates in 5.15 ~ 5.25GHz frequency range. It is restricted in
indoor environment only. This device meets all the other requirements
specified in Part 15E, Section 15.407 of the FCC Rules.
CE Mark Warning
Thisisa classB product.Inadomestic environment,thisproductmaycause
radio interference, in which case the user may be required to take adequate
measures.

RF Exposure Information
This device meets the EU requirements (1999/519/EC) on the limitation of
exposure of the general public to electromagnetic fields by way of health
protection.
The device complies with RF specifications when the device used at 20 cm
from your body.
National Restrictions
This device is intended for home and office use in all EU countries (and
other countries following the EU directive 1999/5/EC) without any limitation
except for the countries mentioned below:
Country
Restriction
Reason/remark
Belarus
Not
implemented
Norway
Implemented
This subsection does not apply for the
geographical area within a radius of 20 km
from the centre of Ny-Ålesund on Svalbard.
Italy
Implemented
The public use is subject to general
authorisation by the respective service
provider.
Russian
Federation
Limited
implementation
1. SRD with FHSS modulation
1.1. Maximum 2.5 mW e.i.r.p.
1.2. Maximum 100 mW e.i.r.p. Permitted for
use SRD for outdoor applications without
restriction on installation height only for
purposes of gathering telemetry information
for automated monitoring and resources
accounting systems. Permitted to use SRD for
other purposes for outdoor applications only
when the installation height is not exceeding
10 m above the ground surface.
1.3.Maximum 100 mW e.i.r.p. Indoor
applications.
2. SRD with DSSS and other than FHSS
wideband modulation
2.1. Maximum mean e.i.r.p. density is 2
mW/MHz. Maximum 100 mW e.i.r.p.
2.2. Maximum mean e.i.r.p. density is 20
mW/MHz. Maximum 100 mW e.i.r.p. It is
permitted to use SRD for outdoor applications
only for purposes of gathering telemetry
information for automated monitoring and
resources accounting systems or security
systems.
2.3. Maximum mean e.i.r.p. density is 10
mW/MHz. Maximum 100 mW e.i.r.p. Indoor
applications.
Ukraine
Limited
implementation
e.i.r.p. ≤100 mW with built-in antenna with
amplification factor up to 6 dBi
ATTENTION: Due to EU law, the country settings must be identical to the
country where the device is operating (important due to non-harmonised
frequencies in the EU).
Restricted to indoor use.

Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs.
Operation is subject to the following two conditions:
This device may not cause interference, and
This device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
l'appareil nedoit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Caution
The device for operation in the band 5150–5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile satellite
systems.
Avertissement
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être
installéet utiliséavec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用
者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現

有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通
信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、
科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行
清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞
或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在
密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進
行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що
передбачені чинними законодавчими актами України.
Safety Information
●When product has power button, the power button is one of the way to
shut off the product; when there is no power button, the only way to
completely shut off power is to disconnect the product or the power
adapter from the power source.
●Don’t disassemble the product, or make repairs yourself. You run the
risk of electric shock and voiding the limited warranty. If you need
service, please contact us.
●Avoid water and wet locations.
●Adapter shall be installed near the equipment and shall be easily
accessible.
●The plug considered as disconnect device of adapter.
●Use only power supplies which are provided by manufacturer
and in the original packing of this product.
This product can be used in the following countries:
AT
BG
BY
CA
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HU
IE
IT
LT
LV
MT
NL
NO
PL
PT
RO
RU
SE
SG
SK
TR
UA
US

TP-LINK TECHNOLOGIES CO., LTD
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: AC1200 Wi-Fi Range Extender
Model No.: RE380D
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all
the technical regulations applicable to the product within the scope of
Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC,
Directives 1999/519/EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other
normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013
EN 50385: 2002
EN 301 893 V1.7.1
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2015-10-11

Appearance.......................................................................1
LED Explanation ...................................................................... 1
Button Explanation................................................................... 2
Positioning the Product............................................................ 2
Option ONE: Horizontal Installation ..................................... 2
Option TWO: Vertical Installation......................................... 3
Connect the Extender to the Internet.................................4
Before You Begin..................................................................... 4
Quick Setup.............................................................................. 5
Option ONE: Using Web Browser........................................ 5
Option TWO: Using WPS (Wi-Fi Protected Setup).............. 9
Entertainment Adapter........................................................... 10
View the Information of the Extender ..............................12
View the Extender’s Current Status....................................... 12
View the Information about the Host Network, the Extender and
the Clients .............................................................................. 13
Manage the Extended Network and Security Settings ....14
Extend another Network ........................................................ 14
Change the Extended SSIDs................................................. 16
Manage the Extender’s Security Settings.............................. 17
Admin Account ................................................................... 17
Access Control to the Extender..........................................17
Change the Extender’s IP Address ........................................19
DHCP Server..........................................................................20
Set the DHCP Server..........................................................20
View the DHCP Client List..................................................21
Manage the Extender ..................................................... 22
Time Settings..........................................................................22
LED Control ............................................................................22
Firmware Upgrade..................................................................23
Backup & Restore...................................................................23
Backup Configurations........................................................23
Restore Configurations.......................................................24
Factory Default Restore..........................................................24
System Log.............................................................................24
Reboot ....................................................................................25
Logout.....................................................................................25
Appendix......................................................................... 26
Factory Default Settings.........................................................26
Troubleshooting......................................................................26
Specifications..........................................................................27
Glossary..................................................................................28
Contents

Appearance
Appearance
This chapter covers the following topics:
LED Explanation
Button Explanation
Positioning the Product
LED Explanation
Name
Status
Indication
(RE)
Solid blue
The extender has established a secure
connection, and the signal strength is adequate.
Solid orange
The extender has established a secure
connection, but the signal strength is too weak.
Blinking
WPS connection is in process.
Off
No active connection.
(5GHz)/
(2.4GHz)
On
The extender is connected to the 2.4GHz or
5GHz wireless network of your host network.
Off
No connection.
LEDs

Appearance
(Power)
On
The extender is on.
Blinking
The extender is initializing.
Off
The extender is off.
(Ethernet)
On
The Ethernet port is connected.
Off
The Ethernet port is not connected.
Button Explanation
(RE/WPS) Button: If your Wireless router supports WPS or QSS function,
you can press the WPS or QSS button and then press the RE button to
establish a secure connection between the Wireless router and the extender.
Reset Button: This button is used to restore the extender’s factory default
settings. There are two ways to reset the extender:
Option One: With the extender powered on, use a pin to press the RESET
button until all the LEDs turn on momentarily, then release the button and
wait the extender to reboot to its factory default settings.
Option Two: Restore the default settings from “System Tools > Backup
&Restore” of the extender's Web-based Management page.
LED Button: You can press the LED button to light up or turn off all the LEDs.
After the LEDs are off, the extender can still work normally.
PowerButton：YoucanpressthePowerbuttontoturnonorofftheextender.
Ethernet Port: Five 10/100/1000Mbps RJ45 Ethernet ports used to add
wireless connectivity to an Ethernet-enabled device such as Internet TV,
DVR, Gaming console and so on. Please note that this port is not allowed to
be connected with router.
Positioning the Product
Ports
Buttons

Appearance
Find the provided base support, insert its clips into the slots marked with ,
then push it leftwards.

Connect the Extender to the Internet
Connect the Extender
to the Internet
This chapter covers the following topics:
Before You Begin
Quick Setup
Entertainment Adapter
Before You Begin
Please read this chapter carefully before using the device. The operating
distance range of your wireless connection can vary significantly depending on
the physical position of the wireless devices. Factors that can weaken signals
by getting in the way of your network’s radio waves are metal appliances or
obstructions, and walls. Typical ranges vary based on the types of materials and
background RF (radio frequency) noise in your home or office.
In order to optimize the performance of the extender, please follow the
instructions below to achieve an ideal location (please make sure it is always
within the wireless coverage of the wireless router).
●Half-way Between - Generally, the ideal location for the extender is half-
way between the Wireless router and Wireless Client. If the wireless
signal is not satisfactory, you may place the extender somewhat nearer to
the Wireless router.
●No Obstacles and Spacious - Clear obstacles in the way between the
extender and Wireless router. It’s better to locate it in a spacious place.
●No Interference - Choose a location away from Bluetooth devices and
other household electronics, such as cordless phone, microwave,and baby
monitor, etc., to minimize signal interference.

Connect the Extender to the Internet
Basic Requirements
Place your extender in a well-ventilated place far from direct sunlight, any
heater or heating vent.
Leave at least 2 inches (5cm) space around the device for heat dissipation.
Turn off your extender and unplug the power adapter in a lighting storm to
avoid damage.
Use Web browser, such as Microsoft Internet Explorer 5.0 or above,
Netscape Navigator 6.0 or above.
Operating temperature of the extender should be 0℃~40℃(32℉~104℉).
Operating humidity of the extender should be 10%~90%RH (Non-
condensing).
Quick Setup
Option ONE: Using Web Browser
Power On
Plug the extender’s adapter into an electrical outlet near your router, then
turn on the extender and wait until the Power LED is lit and solid blue.
Connect to the Extender
●Via Wireless
1) Disconnect the Ethernet (wired) connection to your computer.
2) Click the Wi-Fi icon on the taskbar and connect to the extender's
network (e.g. TP-LINK_Extender_2.4GHz or _5GHz).
●Via Ethernet Cable
Disconnect the wireless connection to your computer.

Connect the Extender to the Internet
Connect the extender to your computer via an Ethernet cable.
Configure
Launch a web browser and type http://tplinkrepeater.net into the
URL field and use admin (all lowercase) for both Username and
Password to log in.
Create a new username and password to log in the web
management page, then click Confirm.
Select your country/region, then click Next.
Per FCC regulations, all Wi-Fi products marketed in the
U.S. are fixed to the U.S. region.

Connect the Extender to the Internet
Select your router's 2.4GHz host network and enter the password,
then click Next.
Select your router's 5GHz host network and enter the password, then
click Next.
If you want to connect the extender only to the router’s
5GHz wireless network, please click Skip.
If your router does not support 5GHz wireless network,
please click Skip to continue.

Connect the Extender to the Internet
Either keep the same SSIDs as your host network or create new
names for the extended networks, then click Next.
Verify your wireless settings and click Finish. The corresponding
LEDs (2.4GHz and 5GHz) should turn on and stay solid.

Connect the Extender to the Internet
Relocate
1) Plug in the extender about halfway between your router (Host
Network) and the Wi-Fi dead zone.
2) Wait until the LED is lit with a solid blue. If not, relocate the
extender closer to the router to achieve a good (or better) signal
quality.
Enjoy!
Both extended networks share the same Wi-Fi password as your main network,
but may have different wireless network names if you customize the SSIDs
during the configuration.
Option TWO: Using WPS (Wi-Fi Protected Setup)
Power On
Plug the extender’s adapter into an electrical outlet near your router, then
turn on the extender and wait until the Power LED is lit and solid blue.
Connect
Press the WPS button on your router.
Immediately press the RE button on your extender. The LED
should change from blinking to solid, indicating that WPS connection
is successful.
Your router should support WPS. Otherwise, please use Option
ONE: Using web browser.
For more information about using WPS on your router,
please refer to the router manufacturer's user guide.

Connect the Extender to the Internet
If you are connecting the extender to a dual-band router but only
2.4GHz ( ) or 5GHz ( ) LED is on, repeat step 1) and 2) to connect
the other band.
Relocate
1) Plug the extender into an electrical outlet about halfway between
your router (Host Network) and the Wi-Fi dead zone.
2) Wait until the LED is lit with a solid blue. If not, relocate the
extender closer to the router to achieve a good (or better) signal
quality.
Enjoy!
The extender shares the same wireless network name (SSID) and wireless
password as your router.
Entertainment Adapter
The extender can be used as a wireless adapter to connect any Ethernet-
enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to
your wireless network.
First, connect the extender to your router using Option ONE or Option TWO,
then you can connect an Ethernet-enabled device to the extender’s Ethernet
port using an Ethernet cable.
By default, the Ethernet ports connect to the 5GHz wireless network. If you want
your Ethernet-enabled device to connect to the 2.4GHz host wireless network
only, please follow the steps below to finish the settings:
Launch a web browser and log into http://tplinkrepeater.net, then go to
Settings > Network page.
If the RE LED does not change from blinking to solid,
please refer to Option ONE: Using Web Browser.
Some ISP gateways disable the WPS function by
default, if the WPS method fails, please refer to Using
your Web Browser.

Connect the Extender to the Internet
Select 2.4GHz as the following figure shows.
Click Save to save the settings.

View the Information of the Extender
View the Information
of the Extender
This chapter covers the following topics:
View the Extender’s Current Status
View the Information about the Host Network, the
Extender and the Clients
View the Extender’s Current
Status
Launch a web browser and log into http://tplinkrepeater.net, then go to
Settings > Status page.
You can view the network connection in the Status webpage.
●The normal status.
●The extender is failed to connect to your router.
●The extender is connected to your router normally, but no transmitting
data. Please check your host network.
●The extender is connected to the router unnormally. Maybe the gateway
is set incorrectly in the Static IP. You can select “Obtain an IP address
automatically” on the “Settigns > Network” page.
3