TP-Link TL-SL1117 User manual

71030511
µ÷Öƽâµ÷Æ÷
µ÷Öƽâµ÷Æ÷
µ÷Öƽâµ÷Æ÷
Rev 3.0
8+1G Gigabit Ethernet Switch
16+1G Gigabit Ethernet Switch
24+2G Gigabit Ethernet Switch
TL-SL1109
TL-SL1117
TL-SL1226
User's Guide
E-mail: [email protected]

EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive
73/23/EEC, this product meets the requirements of the following standards:
ØEN55022
ØEN55024
ØEN60950
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote
risk of electric shock from lightning.
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means
or used to make any derivative such as translation, transformation, or
adaptation without permission from TP-LINK Technologies Co., Ltd. Copyright
© 2005 TP-LINK Technologies Co., Ltd. All rights reserved.
FCC STATEMENT
The Switch has been tested and found to comply with the limits for a class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
ØReorient or relocate the receiving antenna.
ØIncrease the separation between the equipment and receiver.
ØConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ØConsult the dealer or an experienced radio/TV technician for help.

1
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
Package Contents
ØThe following contents should be found in your box:
ØOne Switch
ØOne power cord
ØThis User's Guide
ØRubber footpads for Desk-mount
ØRack-mount kit for installing the switch in a 19-inch rack
Note: If any of the above contents is damaged or missing, please contact
the retailer from whom you purchased the TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch for assistance.
Chapter 1: Introduction of the Product
This chapter describes the features of the TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch.
1.1 Overview of the product
The TL-SL1109/TL-SL1117/TL-SL1226 Gigabit Ethernet Switch provides you
with a high-performance, low-cost, easy-to-use, seamless and standard
upgrade to boost your old network to 1000Mbps. Increase the speed of your
network server and backbone connections, make Gigabit connection to a
server or uplink a network necessarily.
The TP-LINK TL-SL1109/TL-SL1117/TL-SL1226 features a non-blocking
switching architecture that forwards and filters packets at full wire-speed for
maximum throughput. MAC address auto-learning and auto-aging,
TABLE OF CONTENTS
Package Contents............................................................................................1
Chapter 1: Introduction of the Product..............................................................1
1.1 Overview of the product............................................................................1
1.2 Features....................................................................................................2
Chapter 2: Installation.......................................................................................3
2.1 Mounting the Switch on a Desk................................................................3
2.2 Mounting the Switch in a Rack..................................................................3
2.3 Power on...................................................................................................4
Chapter 3: Identifying External Components....................................................4
3.1 Front Panel...............................................................................................4
3.2 Rear Panel................................................................................................5
3.3 LED indicators...........................................................................................5
Appendix A: Specifications................................................................................6
Appendix B: Troubleshooting............................................................................7
Appendix C: Contact Information......................................................................7

IEEE802.3x flow control for Full Duplex mode and backpressure for Half
Duplex mode. It is compatible with all 10,100, and 1000Mbps Ethernet
devices because it is standard-based.
The TP-LINK TL-SL1109/TL-SL1117/TL-SL1226 is plug-and-play and no
configuration is required. Auto MDI/MDI-X cable detection on all ports
eliminate the need for crossover cable or Uplink port. Each port can be used
as general ports or Uplink ports, and any port can be simply plugged into a
server, a hub, a router or a switch, using the straight cable or crossover cable.
Diagnostic LEDs which display link status and activity, allowing you to quickly
detect and correct problems on the network.
1.2 Features
ØComplies with IEEE802.3, IEEE802.3u, IEEE802.3ab standards
Ø8/16/24 10/100Mbps Auto-Sense RJ45 ports supporting Auto-
MDI/MDIX
Ø1/1/2 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-
MDI/MDIX
ØSupports IEEE802.3x flow control for full-duplex model and
backpressure for half-duplex transfer model
ØNon-blocking switching architecture that forwards and filters packets at
full wire-speed for maximum throughput
ØSupports MAC address auto-learning and auto-aging
ØLED indicators for monitoring power, link, activity, speed
Ø19”rack-mountable steel case
ØInternal power supply
Chapter 2: Installation
2.1 Mounting the Switch on a Desk
Before place the Switch on a desk, attach four rubber footpads to the flutes on
the Switch bottom, then lay the Switch on the desktop, where can be have as
much as 5kg placed on top.
Note: Make sure there is a grounded AC outlet within 1.5 meters, and
working well.
Make sure there is free space for radiating heat and air.
Make sure not to place anything to heavy on top of the switch.
2.2 Mounting the Switch in a Rack
The dimension of TL-SL1117/TL-SL1226 is designed according to the
standard 19'' rack-mountable steel case of Electronic Industries Association.
TL-SL1109 can't mount in Rack.
Turn off all the equipment connected to the Switch before mounting it in the
rack, then rivet the two “L”brackets onto each side of the Switch, fasten it with
screws in the rack.
Figure 2-1 Rivet the “L”brackets onto the Switch
24+2GGigabitSwitch
Power
1000M
24681012141618202224
1357911131517192123
TL-SL1226
Link/Act
Link
Link
Act
Act
100Mbps
100Mbps
GIGA1GIGA2
GIGA2
GIGA1
10/100/1000Mbps
9111315
10121416
1357
2468
17192123
1820 2224
10/100Mbps
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
3
2

Figure 2-2 Fasten the Switch in the rack
2.3 Power on
TL-SL1109/TL-SL1117/TL-SL1226 Gigabit Ethernet Switch is powered by AC
power supply. Powering on the Switch, it will automatically initialize and its
LED indicators should respond as follows:
1) All of the LED indicators will flash momentarily for one second, which
represent a resetting of the system.
2) The power LED indicator will remain ON.
Chapter 3: Identifying External Components
This Chapter describes the front panel, rear panel and LED indicators of the
Switch, for example, only the TL-SL1226 is show.
3.1 Front Panel
The front panel of the TL-SL1226 consists of switch LED indicators, 24
10/100Mbps RJ-45 ports and 2 10/100/1000Mbps RJ-45 ports.
Figure 3-1 TL-SL1226 Switch Front Panel sketch
3.2 Rear Panel
The rear panel of the TL-SL1226 only features a power receptacle, which is
an AC power receptacle. Connect the female of the power cord head here,
and the male head to the AC power outlet.
Figure 3-2 TL-SL1226 Switch Rear Panel sketch
3.3 LED indicators
The LED indicators include Power, Link/Act, 1000Mbps and 100Mbps LED
indicators, which are used for monitoring and pre-troubleshooting of the
Switch. The following section shows the LED indicators for the Switch along
with an explanation of each indicator.
Figure 3-3 TL-SL1226 Switch LEDs sketch
ØPower LED: This indicator will light solid red when the Switch powers
24+2G Gigabit Switch
Power
1000M
2 4 6810 12 14 16 18 20 22 24
1 3 57911 13 15 17 19 21 23
TL-SL1226
Link/Act
Link
Link
Act
Act
100Mbps
100Mbps
GIGA1GIGA1 GIGA2GIGA2
GIGA2
GIGA1
10/100/1000Mbps
911 13 15
10 12 14 16
1 3 5 7
2468
17 19 21 23
18 20 22 24
10/100Mbps
100-240V 50-60Hz 0.6A
~
24+2G Gigabit Switch
Power
1000M
2 4 6810 12 14 16 18 20 22 24
1 3 57911 13 15 17 19 21 23
TL-SL1226
Link/Act
Link
Link
Act
Act
100Mbps
100Mbps
GIGA1 GIGA2
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
24+2GGigabitSwitch
Power
1000M
24681012141618202224
1357911131517192123
TL-SL1226
Link/Act
Link
Link
Act
Act
100Mbps
100Mbps
GIGA1GIGA2
GIGA2
GIGA1
10/100/1000Mbps
9111315
10121416
1357
2468
17192123
18202224
10/100Mbps
5
4

MAC Address Learning
Appendix A: Specifications Appendix B: Troubleshooting
1. The Power LED is not lit
ØMake sure the AC power cord connected the Switch with power source
properly.
ØMake sure the power source is ON.
2. The Link/Act LED is not lit when a device is connected to the
corresponding port
ØMake sure that the cable connectors are firmly plugged into the Switch
and the device.
ØMake sure the connected device is turned on and working well.
ØThe cable must be less than 100 meters long(328 feet).
Appendix C: Contact Information
For help with the installation or operation of the TP-LINK TL-SL1109/TL-
SL1117/TL-SL1226 Gigabit Ethernet Switch, please contact us.
E-mail: [email protected]
Website: http://www.tp-link.com
General
Standards IEEE802.3 10Base-T
IEEE802.3u 100Base-TX
IEEE802.3ab 1000Base-T
Topology Star
Protocol CSMA/CD
Data Transfer Rate Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
Network Media 10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
(Cable) EIA/TIA-568 100ÙSTP (maximum 100m)
100Base-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100ÙSTP (maximum 100m)
1000Base-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100ÙSTP (maximum 100m)
Number of Ports 8/16/24 10/100Mbps Auto-Negotiation RJ-45 ports
1/1/2 10/100/1000Mbps Auto-Negotiation RJ-45 ports
LED indicators Power, Link/Act, 100M, 1000M
Transfer Method Store-and-Forward
Automatically learning, automatically Update
Frame Filter Rate 10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
1000Base-T: 1488000pps/Port
Frame Forward Rate 10Base-T: 14880pps/Port
100Base-Tx: 148800pps/Port
1000Base-T: 1488000pps/Port
Safety & Emissions FCC, CE (TL-SL1226)
Power Supply Output
Operating Temperature
Storage Temperature
Environmental and Physical
Dimensions 17.3 7.1 1.7in. (440 180 44mm) (WDH)(TL-SL1117/1226)
11.6 7.1 1.7in. (294 x 180 x 44mm) (WDH) (TL-SL1109)
100-240V~ 50-60Hz (Internal universal power supply)
(TL-SL1117/1226)
220V~ 50Hz (Internal universal power supply) (TL-SL1109)
OOO O
0 C~40 C (32 F~104 F)
OO O O
-40 C~70 C (-40 F~158 F)
Operating Humidity 10%~90% non-condensing
Storage Humidity 5%~95% non-condensing
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
TL-SL1109/TL-SL1117/TL-SL1226
Gigabit Ethernet Switch User's Guide
up. If the LED is not lit, please check the power supply and connection.
ØLINK/ACT LED: The LED indicates Link/Active status. It flashes green
when data is being transmitted or received on the working connection.
Ø1000M LED: The corresponding gigabit port LED indicator will light
solid green when the gigabit port connected to a 1000Mbps device.
Ø100M LED: The corresponding 100M port LED indicator will light solid
green when the 10/100M port connected to a 100Mbps device.
7
6