TP-Link TL-WA801ND User manual

CONTENTS
English ··············································································1
Azərbaycan dili ······························································15
հայերեն··········································································29
Қазақша··········································································43
Русский язык·····································································57
Українська мова ·······························································71
ქართული···········································································85

1
English
Connect to the Access Point with
the Ethernet cable or via wireless.
The default SSID of the Access
Point is TP-LINK_ XXXXXX. The
XXXXXX is the last 6 characters
of the Access Point’s MAC
address.
Plug the provided power adapter
into the power jack on the back of
the Access Point, and the other
end to a standard electrical wall
socket. Then press the ON/OFF
button to power on the device.
Turn on all of your network devices and then check to see if the LEDs on the
Access Point display normally as the diagram below describes.
Note If the distance between the outlet and the Access Point is too long to supply
the power, you can refer to the Power over Ethernet (PoE) solution in
Appendix: With PoE Setup on page 14.
Solid light
Flashing
Solid light or flashing
Flashing if the Wireless
Radio function is enabled
Installation
Note 1. The product model shown in this QIG is “TL-WA801ND”,as an example.
2. Information for technical support can be found in the last page.

2
English
Login
Wireless Settings
A
dialog box will prompt you for the
User name and Password.Ente
r
the default values and click OK.
Note If the dialog box does not pop up, please refer to T3 in Troubleshooting on
page 11 to assign a static IP address 192.168.0.100 for your computer. T2
will give you some help if you forget the password.
User name: admin
Password: admin
Click OK
Note If the LEDs display abnormally, please check to see if all the cable
connectors (power adapter and Ethernet cable) are well connected to you
r
device.
A
fter successfully logging in, the
Quick Setup page will display.
Open your web browser, type in
192.168.0.254 in the address
bar and press Enter.
Click Next

3
English
A. Access Point Mode
Introduction
In this mode, the product will act as a wireless central hub for your wireless LAN
clients, giving a wireless extension for your current wired network.
For Access Point mode, please refer to part
A
on page 3.
For Repeater (Range Extender) mode, please refer to part B on page 4.
For Bridge with AP mode, please refer to part C on page 6.
For Client mode, please refer to part D on page 7.
For Multi-SSID mode, please refer to part E on page 8.
The Operation Mode page will appear then. The TL-WA801ND supports up to five
operation modes. You can refer to the HELP page to know more about the five
modes.
Select the operation mode
based on your need.
Click Next
Note If you click Exit and choose to manually configure the AP on your own need,
please note that the DHCP is enabled during the configuration, it is essential
to disable DHCP when all the settings are finished.

4
English
Settings
1. Create an easy-to-remember name for your wireless network here.
2. Select Region and Channel for your device.
3. Select Most Secure (WPA/WPA2-PSK) mode and enter a wireless password
below to prevent unauthorized access to your AP.
After the settings above, please go to Network Settings on page 9 to continue
the configuration.
B. Repeater (Range Extender) Mode
Introduction
In this mode, the product can extend the coverage of another wireless Access Point
or Router. The universal repeater mode is for the wireless Access Point or Router
which does not support WDS function.
1
2
3
Click Next

5
English
Settings
The window displaying a list of available SSIDs will appear.
You will then return to the previous page.
Select the repeater mode, for
example Universal Repeater.
Click Survey
The security mode will be
selected automatically,
please confirm it and enter
the password that is the
same as on your router or
access
p
oint.
Click Next
Note The setup for WDS Repeater mode is similar to that of Universal Repeate
r
mode.
Find the SSID of the root
Access Point / Router that you
want to repeat, and then click
Connect in the corresponding
row.

6
English
After the settings above, please go to Network Settings on page 9 to continue
the configuration.
C. Bridge with AP mode
Introduction
In this mode, the product can wirelessly connect two or more remote LANs together.
Settings
The window displaying a list of available SSIDs will appear.
You will then return to the previous page.
Click Survey
Find the SSID of the root
Access Point / Router that you
want to bridge, and then click
Connect in the corresponding
row.

7
English
After the settings above, please go to Network Settings on page 9 to continue
the configuration.
D. Client Mode
Introduction
In this mode, the product will act as a wireless adapter to connect your wired devices
(eg. PC, Xbox, PS3, etc. ) to a wireless network.
Settings
The window displaying a list of available SSIDs will appear.
Click Survey
Click Next
Create a name for the Local
Wireless Network.
The security mode will be
selected automatically,
please confirm it and enter
the password that is the
same as on the remote AP.

8
English
You will then return to the previous page.
After the settings above, please go to Network Settings on page 9 to continue
the configuration.
E. Multi-SSID Mode
Introduction
In this mode, the product can be assigned up to four SSIDs to work with your VLAN.
Find the SSID of the Access
Point / Router or WISP, and
click Connect in the
corresponding row.
Click Next
Select the security mode and
enter the password that is the
same as on the root AP.

9
English
Settings
After the settings above, please go to Network Settings on page 9 to continue
the configuration.
Network Settings
Note For advanced configurations on this page, please refer to the User Guide on
the Resource CD.
Click Next
The Network Setting page
will appear then. It is
recommended that you
keep the default settings
on this page.
Note For the configuration of VLAN, please refer to the User Guide on the
Resource CD.
Click Next
You can create up to 4
SSIDs and rename them
here.
Configure the wireless
security for each SSID here.
Click Save to apply the
current security settings for
the selected SSID.
Select Region and Channel.