Trade Price Deals EWB1HD User manual

Instruction manual for
model number:
EWB1HD, EWB2HD &
EWB3HD
2 LEVEL
HEAVY DUTY
WORKBENCH

Thank you for buying this workbench
unit from Trade Price Deals Ltd.
It is very important that you read and understand these
instructions carefully before attempting to assemble
your workbench. This will ensure the safety of yourself
and others during the assembly process, and will
ensure that your product is used correctly and safely
after assembling.
PART NUMBER
EWB1HD, EWB2HD & EWB3HD
UDL*
300KG
*UDL is universally distributed load, or the maximum weight allowed
per level, distributed evenly across the level.
Please take note of your part number, your universally distributed load
(UDL*) per level and the loading diagram on page 7.
MAX WEIGHT PER UNIT
600KG
A B
EWB1HD, EWB2HD & EWB3HD
C D E F
Rubber mallet
TOOLS
REQUIRED
Flat Head Screwdriver
PARTS LIST
Upright
Front / Back Beam
Side Beam
Centre Support Beam
MDF Shelf
Plastic Foot
QUANTITY
4
4
4
2
2
4
A
B
C
D
E
F
NO No & DESCRIPTION
Models EWB2HD will have
4 centre support beams
and EWB3HD will have 8
centre support beams.

ASSEMBLY INSTRUCTIONS
•
•
•
•
•
Always assemble on a firm, level surface. It’s not advisable to
assemble on a carpeted floor
It is recommended that assembly is completed by two people
Always wear protective gloves when assembling
Use a cloth to protect the powder coating when using the mallet
to tap beams into place
Always ensure that the butterflies on the beams (B & C) fully enter
the slots on the uprights (A)
STEP 1.
Select two uprights (A) and push on plastic feet (F) to bases.
Insert the butterflies of a short side beam (C) into the widest part of
the keyholes at the lowest shelf level required.
STEP 2.
Tap beam (C) with a rubber mallet to ensure the butterflies are fully
located in the bottom of the keyholes on both uprights.
Lean the uprights (A) against a wall for support if needed.
STEP 3.
Repeat steps 1 and 2 until you have created a 'ladder style frame'.
TIP: Now is a good time to check the space between the beams suits
the items you want to store on the shelves and adjust as required.
STEP 4.
Select two more uprights (A) and repeat steps 1 and 3 until you have a
second 'ladder style frame'.
TIP: Use the first frame as a template to get the correct spacing.
STEP 5.
Take two long beams (B) and insert the butterflies into the keyholes
on one frame at the same height as the short beams.
Tap into place with a rubber mallet.
STEP 6.
Insert the other ends of the beams (B) into the second frame as in
steps 5.

STEP 6.
Locate Chipboard shelf level (E) into position, tapping lightly to ensure
they sit in recessed beam edges.
Locate support beams (D) onto the metal studs on each long beam (B).
Tap into place and repeat for all levels.
Bend flexible tabs back on themselves, using flat-head screwdriver, for
maximum rigidity.
1. 2. 3.
STEP 8.
•
•
•
Always dispose of packaging responsibly and
appropriately.
Cardboard box – widely recycled.
Plastic sleeve – not widely recycled.
1. Ensure shelving is always kept in good condition.
2. Always adhere to the maximum UDL for your shelving, as shown on
page 2.
3. If your shelving unit gets damaged stop using immediately.
4. Heavier items should always be stored on the lower shelves. Always
load your shelf from the bottom up.
5. Ensure load is evenly distributed as per diagram below.
RECYCLING
GENERAL SAFETY RULES