Craftsman GARAGE STORAGE SOLUTIONS User manual

OPERATOR'S MANUAL
F1379
CRAFTSMA
GARAGE STORAGE SOLUTIONS
FLOOR CABINET - ALL SHELVES
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Sears, Roebuck and Co. Hoffman Estates, IL 60179, USA. F1379A1

SAFETY WARNINGS AND CAUTIONS:
Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage.
Use adequate manpower when assembling and moving this unit. Failure to do so may cause personat injury or product damage.
DO NOT stand on this product. You may fall which may cause personal injury.
DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
Appropriately secure this product before moving it with a forklift.
DO NOT tow with power equipment. The product could tip, which may cause personal injury or product damage.
DO NOT alter this product in any manner. This may cause product damage or personal injury.
Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may
cause personal injuryor product damage.
The maximum weight for each shelf in a door is 7 pounds.
The maximum weight allowed on each fulI width shelf of the FIoor Cabinet is lg0 pounds.
Be sure to secure the Floor Cabinet to a studded or concrete wall. Failure to do so may cause the Floor Cabinet to become unstable
and tip. This may cause personal injury or product damage.
DO NOT step on the shelves. You may fall which may cause personal injury.
J
Tools Required:
Socket Wrench
7116"Socket
318"Socket
3" Socket Extension
314"Wrench
Square
Drill
1/8" DrillBit
Pliers
Hardware Included:
AA
°°©
CC
(11) EE
(7) FF
(11) GG
(4)
(2)
(2)
DD (12) II (2)
HH (1) JJ (8)
iCall 1-80O-4MY-HOME (1-800-469-4663) for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts. )

A
I(6)
C (2)_
G\
H
F\
J
B (2)
D (2)
E (2) __
,J

f -N
STEP 2:
fSTEP 1:
AA
CC
(6)
(2)
AA
(6)
Finger tighten.
NOTE: Ensure B is oriented correctly on each side.
B
CO \
Top
B
°°©
CC
Finger tighten.
(4)
(4)
(4)
AA
Top
Bottom
Square
Square unit and wrench tighten atl bolts.

fSTEP 3:
DD
DD
Top
Wrench tighten to 80 in/Ibs.
(6)
Boffom
fSTEP 4:
NOTE: Steps 4 and 5 attach the leveler feet. Adjustments may
need to be made once the Cabinet is in the desired location.
II (2)
Attach II to E
Attach E to C.
CE
Top
Boffom

f
STEP 5:
Attach D to the Unit
Top
D
fSTEP 6:
DD (2)
Loosely attach C with DD (2). Do NOT tighten untiI after
doors are attached.
C
DD
BoSom
,J

fSTEP 7:
EE (4)
Rotate C away from unit.
InstalI F and G with EE on each end.
EE
Bottom G
F
EE Top
fSTEP 8:
DD
BoSom
Wrench tighten DD (6) to 80 in/Ibs.
(4)
Top
\
,J

fSTEP 9:
FF (2)
GG _ (2)
Attach GG to flange of D at the top and bottom.
Attach FF to the unit behind D at the top and bottom.
GG
F
GG
fSTEP 10:
JJ (8)
Attach JJ to front and back of slots in the door.

f'- _ _Tf--EP 12:
STEP 11 :
AA (1)
(1)
(1)
Attach H to Unit. The part has multiple slots to enable
it to be flush with the wall when aligned with a stud.
H
Wrench tighten.
Cabinet MUST be attached to a stud in a wood frame
wall. Failure to do so may cause personal injury or
product damage.
Hardware provided for wood frame wail use only.
Concrete or other surfaces will require other
hardware (not provided). Failure to secure Cabinet to
a wall may cause personal injury or product damage.
HH (1)
Align Floor Cabinet with a stud. If it is not possible to align
with a stud, use appropriate hardware to anchor to the wall
(not provided). Adjust leveler feet if needed.
Drill 1/8" pilot hole.
Attach Floor Cabinet to stud using HH.
H
HH

fRETAINING CORD ATTACHMENT:
Attach 1to door where desired.
SHELF ADJUSTMENT:
Remove Screws.
Position Shelf.
Reattach Shelf.
DOOR ALIGNMENT:
Loosenbolts.
Align door.
Tighten bolts.
fDDETENT ADJUSTMENT: -'_
Adjust detent when needed.
NOTE: Turn clockwise to tighten, counterclockwise to loosen. |
/
HINT: The more weight in the door the tighter the detent will |
.,e_ub_io work properly.
II
(Lubricate lock with graphite, (yearly).
Periodically the surfaces should be cleaned with a mild
detergent and water.
Auto wax will preserve the unit's luster finish. Apply the
wax as to a car. The wax will also help protect the unit
against scratches.
Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning
fluid.
10