TRADEDX SSR-4N108L User manual

JBOD SSR-4N108L
User Manual

Compliance information
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council Directive
2014/30/EU on the approximation of the laws of the Member States relating to
electromagnetic compatibility. TradeDX cannot accept responsibility for any failure to satisfy
the protection requirements resulting from a non-recommended modification of the product.
This product has been tested and found to comply with the limits for Class A Information
Technology Equipment according to CISPR 32/European Standard EN 55032. The limits for
Class A equipment were derived for commercial and industrial environments to provide
reasonable protection against interference with licensed communication equipment.
Attention: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
CE Declaration of Conformity
This product has been tested in accordance to, and complies with the European Low Voltage
Directive (2014/35/EU) and European EMC Directive (2014/30/EU).
The product has been marked with the CE Mark to illustrate its compliance.
Disclaimer
The information in this document is subject to change without notice. The manufacture makes
no representations or warranties with respect to the contents hereof and specifically disclaims
any implied warranties of merchantability or fitness for any particular purpose. Furthermore, The
manufacturer reserves the right to revise this publication and to make changes from time to time
in the content hereof without obligation to notify any person of such revision or changes.

Safety Information
Read this important safety information section. Retain this manual for reference. Read this
section before servicing.
CAUTION:
To reduce the risk of electric shock, this JBOD should only be serviced by qualified service personnel.
RTC Battery
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by
the manufacturer. Discard used batteries according to the manufacturer’s instructions.
Laser Drive Equipment
The optical transceiver module in this JBOD is a laser Class 1 product.
Ambient Operation
This equipment cannot be operated above an ambient operation temperature of 40
degrees centigrade.
Equipment Location
This equipment can only be accessed by SERVICE PERSONNEL or by USERS who have been
instructed about the reasons for the restrictions applied to the location. Access is through the
use of a TOOL or lock and key, or other means of security, and is controlled by the authority
responsible for the location.

Further Safety Information
Be sure to read all caution and danger statements in this documentation before performing
the instructions. Read any additional safety information that comes with your JBOD or
optional de- vice before you install the device.
Safety Precautions
For your protection, observe the following safety precautions when setting up your equipment:
 Follow all cautions and instructions marked on the equipment.
 Ensurethatthevoltageandfrequencyofyourpowersourcematchthevoltageand
frequency inscribed on the equipment’s electrical ratinglabel.
 Neverpushobjectsofanykindthroughopeningsintheequipment.Dangerous
voltagesmaybe present.
 Conductiveforeignobjectscouldproduceashortcircuitthatcouldcausefire,electric
shock,or damage to your equipment.
Safety Instructions
1. Please read these safety instructionscarefully.
2. Please keep this Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning. Don’t use liquid or sprayed
detergent for cleaning. Use moist sheet or cloth for cleaning.
4. For pluggable equipment, the socket-outlet must be installed near the equipment and must be
easilyaccessible.
5. Please keep this equipment from humidity.
6. Place this equipment on a safe reliable surface when installing. A drop or fall could cause injury.
7. Enclosure openings are for air circulation and protect the equipment from overheating. DO NOT
COVER THE OPENINGS.
8. Make sure the voltage of the power source matches rated voltages.
9. Place the power cord so that it won’t be stepped on or tripped over. Do not place anything on top
of the power cord.
10. All cautions and warnings on the equipment should benoted.
11. If the equipment is not used for a long time, disconnect the equipment from outlet to avoid dam-
age to the system by transient voltages.
12. Do not spill liquids onto equipment; this may cause fire or electricalshock.
13. Never open the equipment. For safety reasons, the equipment should only be opened by qualified
service personnel.
14. If any of the following situations arises, have the equipment checked by qualifiedservice:
a) The power cord or plug isdamaged.
b) Liquid seeped into theequipment.
c) The equipment has been exposed tomoisture.
d) The equipment does not work well or operation does not match behavior describe in user’s
manual.

e) The equipment has been dropped ordamaged.
f) The equipment has obvious signs ofdamage. DO NOT LEAVE THIS EQUIPMENT IN AN
ENVIRONMENT WHERE TEMPERATURES EX- CEED 60 °C (140 °F); IT MAY DAMAGE THE
EQUIPMENT.
Symbols
The following symbols will appear in this manual to indicate different safety precaution:
Hazardous voltages are present. To reduce the risk of electric shock and danger to
personal health, follow the instructions.
There is a risk of personal injury and equipment damage. Follow the instructions.
Hot surface. Avoid contact. Surfaces are hot and may cause personal injury if
touched.
Safety Statements
DANGER:
Electrical current from power, telephone, and communication cables is hazardous. To
avoid a shock hazard:
•Do not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
•Connect all power cords to a properly wired and grounded electrical outlet.
•Connect to properly wired outlets any equipment that will be attached to this product.
•When possible, use one hand only to connect or disconnect signal cables.
•Never turn on any equipment when there is evidence of fire, water, or structural damage.
•Disconnect the attached power cords, telecommunications systems, networks, and
modems before you open the device covers, unless instructed otherwise in the installation
and configuration procedures.
•Connect and disconnect cables as described in the following table when installing, moving,
or opening covers on this product or attacheddevices.
To Connect:
To Disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlet.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlet.
4. Remove all cables from devices.
5. Turn device ON.

CAUTION:
When replacing the lithium battery, use only Foxconn Part Number XXXXX or an equivalent type battery rec-
ommended by The manufacture. If your system has a module containing a lithium battery, replace it only with the
same module type made by the same manufacturer. The battery contains lithium and can explode if not properly
used, handled, or disposed of.
Do not:
Throw or immerse into water
Heat to more than 100°C (212°F)
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the
following:
Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
Use of controls or adjustments or performance of procedures other than those specified herein might
result in hazardous radiation exposure.
DANGER:
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid
direct exposure to the beam.
DANGER:
Class 1 Laser
CAUTION:
The following label indicates sharp edges, corners, or joints nearby.

CAUTION:
The following label indicates a hot surface.
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off the electrical
current supplied to the device. The device also might have more than one power cord. To remove all electrical
current from the device, ensure that all power cords are disconnected from the power source.
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
Hazardous voltage, current, and energy levels are present inside any component that has this label attached.
There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact
a service technician.
Attention: This JBOD is suitable for use on an IT power distribution system whose maximum phase-to- phase
voltage is 240 V under any distribution fault condition.
DANGER:
Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. To avoid these
hazards, ensure that your system electrical requirements do not exceed branch circuit protection require- ments.
Refer to the information that is provided with your device for electrical specifications.

CAUTION:
Do not place any object on top of rack-mounted devices.
Attention: This JBOD is suitable for use on an IT power distribution system whose maximum phase-to-phase voltage
is 240 V under any distribution fault condition.
CAUTION:
Hazardous moving parts are nearby.

Table of Contents
Introduction ................................................................................................................................................13
Checklist .................................................................................................................................................. 13
System Tour ............................................................................................................................................ 13
Front View............................................................................................................................................... 14
Rear View ................................................................................................................................................15
Rear Panel Board................................................................................................................................. 15
System Architecture................................................................................................................................ 16
System Operations......................................................................................................................................17
Powering on ............................................................................................................................................ 17
Powering down ....................................................................................................................................... 17
Set Storage Configuration....................................................................................................................... 17
Set steps with BMC IPMI command.................................................................................................... 17
Get JBOD Topology Configuration ...................................................................................................... 19
Hardware Installation .................................................................................................................................21
Introduction ............................................................................................................................................21
Safety Measures.................................................................................................................................. 21
Power supply Units (PSU) ....................................................................................................................... 22
Removing a Power Supply Unit...........................................................................................................22
Installing a Power Supply Unit ............................................................................................................ 22
System Fans ............................................................................................................................................ 23
Removing a System Fan ...................................................................................................................... 23
Installing a System Fan........................................................................................................................ 23
HDD Drawer ............................................................................................................................................24
Opening a HDD Drawer.......................................................................................................................24
Closing a HDD Drawer......................................................................................................................... 24
Removing a HDD Drawer ....................................................................................................................25
Installing a HDD Drawer...................................................................................................................... 26
Removing a HDD Drawer in limited space .......................................................................................... 28
Installing a HDD Drawer in limited space............................................................................................ 31
Top Cover ................................................................................................................................................ 33
Removing a Rear Top Cover ................................................................................................................ 33

Installing a Rear Top Cover ................................................................................................................. 34
Removing a Front Top Cover............................................................................................................... 35
Installing a Front Top Cover ................................................................................................................ 36
Storage .................................................................................................................................................... 37
Installing a 3.5'' HDD ........................................................................................................................... 37
Removing a 3.5'' HDD..........................................................................................................................39
Expander Board....................................................................................................................................... 40
Removing an Expander Board.............................................................................................................40
Installing an Expander Board ..............................................................................................................41
Cable Cover ............................................................................................................................................. 42
Removing a Cable Cover ..................................................................................................................... 42
Installing a Cable Cover.......................................................................................................................42
Cable Chain Module................................................................................................................................ 43
Removing a Cable Chain Module ........................................................................................................43
Installing a Cable Chain Module.......................................................................................................... 43
Rear Panel Board (RPB)........................................................................................................................... 44
Removing Rear Panel Board................................................................................................................ 44
Installing Rear Panel Board ................................................................................................................. 45
Fan Board ................................................................................................................................................ 45
Removing a Fan Board ........................................................................................................................ 45
Installing a Fan Board..........................................................................................................................46
Power Distribution Board Cover (PDB Cover).........................................................................................47
Removing a Power Distribution Board Cover ..................................................................................... 47
Installing a Power Distribution Board Cover....................................................................................... 47
Power Distribution Board (PDB) ............................................................................................................. 48
Removing a Power Distribution Board................................................................................................ 48
Installing a Power Distribution Board ................................................................................................. 48
Chassis Management Module (CMM) .................................................................................................... 49
Removing a Chassis Management Module......................................................................................... 49
Installing a Chassis Management Module .......................................................................................... 49
Inner Rail .................................................................................................................................................50
Removing an Inner Rail ....................................................................................................................... 50