easyRAID Q08QA-2GR2 User manual

easyRAID Q08QA-2GR2
Hardware Manual
42-30000-5107
iSCSI 1Gb to Serial ATA II
Disk Array System
Version 1.0

easyRAID Q08QA-2GR2
iSCSI 1Gb to Serial ATA II
Disk Array System
Hardware User Manual

i
Table of Contents
Preface................................................................................................................... i
Chapter 1 System Requirements
Operating Environment .................................................................................... 1
VT100 Terminal Settings .................................................................................. 1
Chapter 2 Basic Configuration
Unpacking .............................................................................................................3
Components .......................................................................................................... 5
Closed Front Panel ........................................................................................... 5
Open Front Panel ............................................................................................. 6
Disk Tray .......................................................................................................... 7
Rear View ......................................................................................................... 8
Installing Disks ...................................................................................................... 9
Making Connections ........................................................................................... 11
Connecting the Host Interface ........................................................................ 11
Connecting the GUI management port ........................................................... 11
Connecting and Turning on the Power ........................................................... 12
Mounting in a Rack ............................................................................................. 13
Installing the Rail Extenders ........................................................................... 14
Chapter 3 Maintenance
Replacing a Disk ................................................................................................. 15
Replacing a Power Supply .................................................................................. 16
Upgrading Memory .............................................................................................18
Appendi
Hardware Specifications ..................................................................................... 21

i
Preface
About this Manual
This manual is designed to make the disk array system as easy to use as possible. Information
contained in this document has been checked for accuracy, but no guarantee is given that the con-
tents are correct. Information and specifications are subject to change without notice.
Copyright Notice
© Copyright 2008
All rights reserved. This disk array system and related documentation are protected by copyright
and are distributed under licenses restricting their use, copying, and distribution. No part of this
documentation may be reproduced in any form by any means without prior written authorization
and its licensors, if any.
Conventions
Caution
This symbol is used to remind users to pay attention to important
descriptions regarding usage and maintenance (repair) or additional
important information related to this disk array system.
Note
This symbol is used to remind users of useful information that can make
procedures such as configuration easier to accomplish.

ii
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
Preface
– Important Safety Instructions, Care and Handling
Important Safety Instructions, Care and Handling
Before starting, take a few minutes to read this manual.
Read all of these instructions and save this manual for
later reference.
Protect the disk array system from extremely high or low
temperatures. Let the disk array system warm (or cool)
to room temperature before using it.
Protect the disk array system from being bumped or
dropped. Do not place the disk array system on an
unstable cart, stand, or table. It may fall, causing serious
damage to the product.
Keep the disk array system away from magnetic forces.
Do not use the disk array system near water.
Keep the disk array system away from dust, sand, or dirt.
Gaps and openings in the cabinet are provided for venti-
lation. Never block or cover these openings, because
the disk array system may overheat and become unreli-
able. Don’t place the disk array system on a bed, sofa,
rug, or other similar surface.
Do not place the disk array system near or over a radia-
tor or other heat source.
Refer to the rating plate for the correct voltage and
ensure that the appliance voltage corresponds to the
supply voltage.
V

easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
iii
Preface
– Important Safety Instructions, Care and Handling
The appliance must be grounded. The disk array system
is equipped with a 3-wire grounded type of power cord.
This power cord will only fit into a grounded type of
power outlet.
If an extension cord or a power center is used with the
disk array system, make sure that the total current con-
sumption of all products plugged into the wall outlet
does not exceed the ampere rating.
Do not place the disk array system where the cord will
be walked on.
Never push any kind of object into the disk array system
through cabinet gaps and openings, since they may
touch dangerous voltage points and cause a risk of fire
or electric shock.
Unplug the power cord from the wall outlet before clean-
ing. Keep the disk array system dry. Do not use liquid
cleaners, aerosol cleaners, or a wet cloth. Use a damp
cloth for cleaning.
Except as specifically explained in this User Manual, do
not attempt to service the disk array system by yourself.
Opening or removing the covers may expose you to
dangerous voltages.
Unplug this product from the wall outlet and refer servic-
ing to qualified service personnel under the following
conditions.
• If the disk array system has been exposed to
water or any liquid.
• If the disk array system has been dropped or the
cabinet damaged.
Users should not remove the cover.
Disconnect all power supply cords before servicing.
Fan1
Power1
oGGwGGY

iv
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
Preface
– Important Safety Instructions, Care and Handling
Placement Notes
• The disk array system LCD panel can be damaged by exposure to
direct sunlight. Limit exposure to subdued or indirect sunlight only.
• The disk array system should be used only in clean environments
that are free from airborne contaminants such as dust, dirt, and
smoke. Excessive moisture or oil particles in the air can also hinder
disk array system performance.
• To reduce the possibility of data errors caused by electromagnetic
interference, locate the disk array system at least five feet away
from electrical appliances and equipment that generates magnetic
fields.
Power Supply Safety Notes
• To avoid electric shocks, do not use an extended power cord or an
outlet that does not match the disk array system plug or leaves the
plug exposed.
• The disk array system has a 3-wire grounded plug. The third pin
connects to ground; do not remove it.
• If the power cord or plug is damaged or worn, unplug it immediately
and contact a qualified service technician for maintenance.
• To avoid fire or electric shocks, do not overload electric power out-
lets.
CAUTION : MULTIPLE POWER SOURCES
Disconnect all AC power cords to completely power from the unit
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
CAUTION
The thumbscrews on the rear surface shall be secured by the screw-
driver, which cannot be loosened by bare hands to prevent the uninten-
tional access to the hazardous parts inside the equipment.

1
1 System Requirements
Ensure that the following requirements are met before installing the disk array system.
Operating Environment
• 15 cm (6-inches) of space around the disk array system for proper ventilation
• ambient temperature of 5°C to 40°C (40°F to 104°F)
• ambient non-condensing relative humidity of 20% to 80%
• dust, smoke, and oil free environment
• no large magnetic fields, such as those generated by a high voltage power cables and
motors, etc.
• no direct sunlight
• a flat, stable surface capable of supporting the disk array system
VT100 Terminal Settings
Refer to the following table for a summary of VT100 terminal settings required to communicate
with the disk array system. Refer to your system manual for instructions on setting up the VT100
terminal settings.
Item Required Setting
Connection Serial Port (COM1 or COM2)
Protocol RS232 (Asynchronous)
Cabling Null Modem cable
Baud Rate 115200
Data Bits 8
Stop Bit 1
Parity None

3
2 Basic Configuration
This chapter describes disk array system connections and disk installation.
Unpacking
Contact your supplier if any of the following items are missing or damaged.
Caution
The disk array system is heavy. Be careful when lifting and moving it.
Item qty
Disk Array System 1 pcs
Hard Disk Tray 8 pcs
Hardware and Software User Manual 1 set
Rail 1 set
Rail Extender 1 set
PowerP/SFail Access
Enter ESC
HardwareUser Manual
easyRAID Q08QA-2GR2
iSCSIto Serial ATA
DiskArraySystem
PowerP/SFailAccess
EnterESC Pri/Sec
PowerP/SFailAccess
EnterESC Pri/Sec
SoftwareUser Manual
easyRAID Q08QA-2GR2
iSCSIto Serial ATA
DiskArraySystem

4
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
2
Basic Configuration – Unpacking
Front Panel Key 2 pcs
RJ45 LAN Cable 1 pcs
Power Cable 2 pcs
RS-232 Cable 1 pcs
Screw pack 2 packs
Fix Screw pack M5 2 packs
Fix Screw pack M6 2 packs
Fix Screw pack UNC #10-32 2 packs
Item qty

easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
5
2
Basic Configuration – Components
Components
Closed Front Panel
No. Name Description
1LCD panel Display warning, operating, and configuration
information.
2Power-on indicator Indicate the disk array system power is on.
3Power supply fail indicator Indicate a failed power supply.
4Host computer access indicator Indicate data transfer between the disk array sys-
tem and the host computer.
5Up function button Move up in the LCD menus.
6Down function button Move down in the LCD menus.
7Enter function button Select a menu item or confirm a choice or entry.
8Escape function button Return to the previous LCD menu without making
changes.
9Lock Lock front cover.
Power P/S Fail Access Enter ESC
1
3 4
5 6
2
78 9

6
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
2
Basic Configuration – Components
Open Front Panel
No Name Description
1-8 Disk trays 1-8 Removable hot swap disk trays
9Front panel door Protect the disks and house the LCD panel
Disk1
Disk2
Disk3
Disk4
Disk5
Disk6
Disk7
Disk8
Disk Mapping
Color Status
Bule Access
Green Disk Online
Red No Disk
Tray LED Indication
1 2 3 4 5 6 7 8
9

easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
7
2
Basic Configuration – Components
Disk Tray
No. Name Description
1Power/Error indicator LED
Different colors indicate different disk states:
• Green – Disk online
• Orange – Disk full
• Red – No disk
2Access indicator LED This blue LED indicates that the disk is being
accessed.
3Tray handle Release the disk tray.
21
Front
3

8
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
2
Basic Configuration – Components
Rear View
Term UPS
Host 1 Host 2
LAN
1
89
10
3
11
1213
2
7
14 4 5
6
No. Name Description
1
Cooling fan 1
System cooling fan.
2
iSCSI Host Port 1
Connect to the host server.
3
iSCSI Host Port 2
Connect to the host server.
4
RS-232 Port
Connect to a VT100 terminal or equivalent.
5
UPS port
Data port for uninterruptable power supply.
6
Cooling fan 2
System cooling fan.
7
Power Supply 2
Removable redundant power supply 2.
8
Power Supply Handle
For power supply removal.
9
Power Supply AC In
Connect to a 100-240 VAC power source.
10
Power Supply Switch
Switch the power on or off.
11
Ethernet Port
Use for browser-based configuration.
12
Power Supply 1
Removable redundant power supply 1.
13
Power Supply Handle
For power supply removal.
14
Power Supply AC In
Connect to a 100-240 VAC power source.

easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
9
2
Basic Configuration – Installing Disks
nstalling Disks
This section describes how to install disks in the disk array system.
1Unlock the front panel door, then pull it open.
2Push the button (A) to release the disk tray handle. Pull the handle (B) to release the tray.
3Align the rear of the disk with the rear of the disk tray.
4Insert the disk into the disk tray and fix into place with screws supplied with the disk.
Disk1
Disk2
Disk3
Disk4
Disk5
Disk6
Disk7
Disk8
Disk Mapping
Color Status
Bule Access
Green Disk Online
Red NoDisk
Tray LED Indication
AB

10
easyRAID Q08QA-2GR2 Serial ATA II Disk Array System
2
Basic Configuration – Installing Disks
5Slide the disk tray back into the empty slot (A), then slowly close the disk tray handle
(B).
6Repeat steps 2 to 5 until all of the required disks have been installed.
7Push the front panel door closed, and lock it.
AB
Disk1
Disk2
Disk3
Disk4
Disk5
Disk6
Disk7
Disk8
Disk Mapping
Color Status
Bule Access
Green Disk Online
Red No Disk
Tray LED Indication