Tranberg TEF 2562 AL User manual

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2562 AL
SEALED BEAM FLOODLIGHT
USER MANUAL
IMPORTANT
Read this instruction carefully before installing the
product
TUM 2408 REV. A 28.06.2011
256A3283

TEF 2562 AL SEALED BEAM FLOODLIGHT USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval,
may be a safety violation. The manufacturer will in no
circumstance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specific procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
• 13 mm wrench –for assembling and adjust the floodlight.
• 25 mm wrench –for tightening the pressure nut.
• 5 mm flat screwdriver –for connecting the lamp input.
MAINTENANCE INSTRUCTIONS
The luminaire should be inspected according to Company
routines.
When cleaning, use only mild detergents. Alcohol or
petroleum based products may damage lens, paint or
plastic components.
APPLICATIONS
• Deck lighting
• Lifeboat stations
• Emergency light
• Work light
• For use in safe area
APPROVALS
NA

TEF 2562 AL SEALED BEAM FLOODLIGHT USER MANUAL
INSTALLATION INSTRUCTIONS
SPARE PARTS
Description Part No.
Lamp input, 24V, 135W 55° x 55° 9400 014
Lamp input, 24V, 135W 80° x 25° 9400 015
Mounting the lamp:
The lamp is mounted to the structure by means of two
bolts M8 (maximum), spaced at 31.5 mm. The lamp may
be adjusted sideways up to 80 degrees, allowing it to cover
a large area. Tighten the bolts when the desired position is
found. The vertical position is set by tightening the centre
bolt when the correct position is found.
Opening the lamp:
The lamp housing is opened by loosening the three
wingnuts about 5-10mm. Please make sure to support the
lamp insert when opening the lamp.
Cable entry:
The cable gland nut is opened fully or partly, and the cable
is pushed is pushed through the cable gland. Tighten the
gland nut to secure the cable and obtain a watertight entry.
It is recommended to have a wire length inside the housing
of approx. 100mm, as too long wires may reduce the
space required for the lamp insert. Ensure that the cable
is attached to the structure in a way that prevents water to
follow the cable into the lamp housing.
Electrical connections:
The electrical termination (12/24 VAC/VDC) is done
directly to the lamp insert. Ensure that the connections
are proper, but do not overtighten the screws as this may
damage the lamp insert.
Closing the lamp:
Ensure that the black o-ring in the lamp housing is in the
groove, then set the lamp insert into the recess. Move
the three fixing brackets over the lamp insert and tighten
the three wingnuts. Do not overtighten the screws.
MOUNTING DIMENSIONS

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2562 AL SEALED BEAM FLOODLIGHT USER MANUAL
TECHNICAL DATA
Material: Cast aluminium, with glass sealed beam lamp
Input voltage: 24V DC 135W
IP-rating: IP56
Standard cable entries: M20
For use in: Safe area
Height: 215 mm.
Width: 157 mm.
Depth: 110 mm.
Weight: 0,93 kg.