Tranberg TEF 9971 LED User manual

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 9971 LED
HELIDECK FLOODLIGHT LIGHT
SAFE AREA
USER MANUAL
TUM5390
IMPORTANT
Read this instruction carefully before installing the
product
COPYRIGHT
©2016 Tranberg AS
The information contained in this document remains the
sole property of Tranberg AS. No part of this document
may be copied or reproduced in any form or by any
means, and the information contained within it is not
to be communicated to a third party, without the prior
written consent of Tranberg AS. The document, or any
part of it, may not be translated to any other language
without the written approval from Tranberg AS.
DISCLAIMER
Tranberg AS endeavors to ensure that all information in
this document is correct and fairly stated, but does not
accept liability for any errors or omissions.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the manufactur-
er’s specification, may be a safety violation. The manufac-
turer will in no circumstance be held responsible for such
activity. For your health and safety, always use safety gear
suited for the task. Be certain to follow codes, regulations
and/or specific procedures that are related to the installa-
tion.

TEF 9971 LED HELIDECK FLOODLIGHT USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
TOOLS REQUIRED
Regular tools required for installation.
• Tools for mounting, e.g. 13 mm wrench – to fasten the
mounting bracket to the deck and adjust the angle of
the lamp.
• 3 mm hexagon key (Unbraco/Allen key) for mounting
the lid to the termination compartment, and to loosen
the screws for the terminal assembly, if necessary.
• 32mm wrench to disassemble the blind plug and as-
semble the cable gland.
MAINTENANCE INSTRUCTIONS
The floodlight should be inspected according to Company
routines. The manufacturer suggests regular check for wa-
ter intrusion.
When cleaning, use only mild detergents. Alcohol or petro-
leum based products may damage the gaskets.
APPLICATIONS
• Floodlight on helideck, general Floodlighting
• Safe area
Warning – DO NOT OPEN WHEN ENERGIZED
SAFETY PRECAUTIONS
Note that changes to the product and /or installation of
components which do not conform to the manufacturers
specification, may be a safety violation. The manufacturer
will not under any circumstances be held responsible for
such activity. For your health and safety, always use safety
gear suited for the task. Be certain to follow codes, regu-
lations and /or specific procedures that are related to the
installation.

Dim
L
N
PE
TEF9970/TEF9971
Dim
L
N
PE
TEF9970/TEF9971
Floodlight 1 Floodlight 2
Dim
On/Off
L
N
PE
Off - Full Light
On - Dim 50%
When mounting the lid to the connection compartment,
make sure no cables or the safety wire are jammed between
the two parts. Check the gasket and make sure that the
gasket has no damages on the surface! This will dramati-
cally reduce the ingress protection. Not following these in-
structions may lead to a risk of water ingress into the lu-
minaire. The manufacturer assumes no responsibility when
these guidelines are not followed.
The terminals in this luminaire consist of a terminal block
for phase conductors and PE. Two extra M5 screws are fit-
ted to accept PE wires. The terminal block is of the “Cage
clamp” type, and there is no need for a tool to connect or
disconnect the phase conductors. Nevertheless a large
screwdriver, preferably flathead, may be a good help.
Any damage caused by the use of an incorrect combination
of cable and cable gland is not the responsibility of Tranberg
AS and is not covered by warranty.
TEF 9971 LED HELIDECK FLOODLIGHT USER MANUAL
INSTALLATION INSTRUCTIONS
Only qualified personnel are allowed to perform installation
and maintenance tasks to this product.
The equipment is ready for installation when leaving the
production facilities of Tranberg AS. Check the condition of
the equipment and the contents when unpacking. Any dam-
age done to the equipment during transportation is not the
responsibility of Tranberg AS. If the content is not complete,
file a claim to the manufacturer immediately.
The TEF 9971 is delivered with several mounting options. A
mounting bracket for flat surfaces is standard. For the light
output to be in accordance with any regulations listed in this
document, the helideck floodlight must be mounted on a
horizontal surface coincident with the helideck.
The luminaire must always be installed in an upright posi-
tion. Any other mounting positions should not be used for
permanent installation, without a confirmation from Tran-
berg’s technical department. If the luminaire is mounted on
a vessel or a floating installation, movements such as roll
and pitch, which moves the luminaire out of its original up-
right position, is not taken into account.
Mounting Details
997A108863
Termination
997A108807
Field Connections
997A110125

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 9971 LED HELIDECK FLOODLIGHT USER MANUAL
TECHNICAL DATA
Material: Marine grade aluminium, power coated and anodized. Impact resistant
safety glass.
Input voltage: 100-277 V ±10%, 47-63Hz
Short-circuit breaking capacity: 1500A
Light output: 3100 lm, 4000 K
Expected lifetime: 50,000 hours (L70)
Power consumption: 40W
Ingress protection: IP 66. IP 67/67 without drain plug. (EN 60529)
Ambient temperature: Operation: -40°C to +55°C
Storage: -55°C to +55°C
Weight: 9 kg
Mounting: Four mounting holes Ø12mm
Cable entries: 2 x M25 entries. Delivered with 2 x M25 cable glands, Ø11-20.1mm.
Dimensions:
997A110266