Tranberg TEF 9964 Helideck User manual

R. Stahl Tranberg AS
[e-mail] | stahl-tranberg.com
Main oce: Strandsvingen 6 | N-4032 Stavanger | Norway | T [phone] | F+47 51 57 89 50
Oce Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T [phone]
IMPORTANT
Read this instruction carefully before installing the
product
LIGHTING
TEF 9964 XENON HELIDECK
FLOODLIGHT INDUSTRY
SAFE AREA
USER MANUAL
Subject to change without prior notice TUM1024 REV. L 26.01.2022

TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval,
may be a safety violation. The manufacturer will in no
circumstance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specic procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
• 17 mm wrench –for assembling the oodlight.
• 13 mm wrench –for adjusting the angle of the light.
• 8 mm at screwdriver –for open/closing the cover of the
junction box.
• 3 mm at screwdriver –for installing the cable in the
terminal block.
• 5,5 mm at screwdriver –for removing the lamp insert.
• 32 mm wrench -to assembly the cable gland
• 30 mm wrench -to tighten the lock nut and the pressure
nut
MAINTENANCE INSTRUCTIONS
The luminaire should be inspected according to Company
routines. The manufacturer suggests regular check for
water intrusion/condensation which should be removed
immediately. Check the drain plug / drain hole function.
When cleaning, use only mild detergents. Alcohol or
petroleum based products may damage lens, paint or
plastic components.
RUBBER SEAL
Cable diameter Size rubber seal Part No. Cable gland kit
11,0 - 15,0 mm Ø26/15,0x10mm 622 2502
15,0 - 20,1mm Ø26/20,3x10mm 622 2502
Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland,
also make sure to use the correct rubber seal when you install the luminaire
APPLICATIONS
• Floodlighting of helicopter landing areas
• For use safe area
• Floodlighting

TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
INSTALLATION INSTRUCTIONS
The oodlight should be installed according to the
calculated light distribution plan.
1.
The glass in front should
face the centre at the
helideck, unless stated
otherwise.
2.
Secure the oodlight to
the helideck by means
of four M10 bolts.
3.
Open the enclosure cover
on rear. Replace cable
gland gaskets as
required to match the cable
diameter. Unused cable
glands should always
be replaced with a blind plug.
4.
Connect cables and
replace the enclosure cover.
DIMENSIONS
5.
Luminaire housing shall be connected to earth potential by groundwire of min. crossection 2,5mm² / 14AWG
996A106032

TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
REPLACING XENON LIGHT BULB
Loosen clamps and remove front ring
Warning ! High voltage components inside lamp. Make sure to disconnect
power before opening.
Distance bracket
Distance bracket
Holding clip
Old version:
2. REMOVE HOLDING CLIP AND/
OR DISTANCE BRACKET
1. REMOVE FRONT RING
3. SLIDE OUT LAMP INSERT
New version:

TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
4a-1:
Disconnect the high voltage plug from the light bulb.
Position lamp removal tool over locking ring as shown
below. twist approx. 30 degrees anti-clockwise.
4a-2:
Remove xenon lamp
Xenon lamp
Locking ring
4b-1:
Disassemble the reector unit. 3 x M4 screws
Disconnect the hight voltage plug.
4b-2:
Position lamp removal tool over locking ring as shown
below. Twist approx. 30 degrees anti-clockwise.
4b-3:
Remove xenon lamp
Locking ring
Xenon lamp
4A. REMOVE LIGHT BULB, NEW VERSION 4B. REMOVE LIGHT BULB, OLD VER
Note: make sure the new xenon bulb is clean. Do not touch the glass part of the bulb.
Mount lamp back together in reversed order.
5. INSERT NEW XENON BULB

R. Stahl Tranberg AS
[e-mail] | stahl-tranberg.com
Main oce: Strandsvingen 6 | N-4032 Stavanger | Norway | T [phone] | F+47 51 57 89 50
Oce Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T [phone]
TEF 9964 XENON HELIDECK FLOODLIGHT INDUSTRY USER MANUAL
TECHNICAL DATA
Material: Acid proof stainless steel. Polycarbonate front glass.
Input voltage: 230/254 VAC 50/60Hz
110/120 VAC 50/60Hz
24 VDC
Power consumption: 50Watt
IP-rating without drain plug: IP 66/67 ( according to EN 60529)
IP-rating with drain plug: IP 66
Cable glands: 2 X M25, E204/622 M25/D kit
Cable diam: 11,0-15,0 mm
15,0-20,1 mm
Area of use: Safe area
Weight: 10 kg.
SPARE PARTS
Part No.
Xenon Lamp, D2S. 35W, For TEF 9964 9400074
Front Glass 3241
High Voltage Igniter Unit Xenon 9400103
Locknut for Xenon D2S 9400108
Transformer W/ Mounting Bracket for 9964, 230/254 VAC 4386
Transformer W/ Mounting Bracket for 9964, 110 VAC 4387
Rectier For 9964 Xenon Helideck Light 3069
Cable Gland Exe E204/622 M25/D kit 11,0-20,1 mm/9mm Brass 6222502
Complete Insert for TEF 9964 230/254V 3173
Complete Insert for TEF 9964 110V 3249
Complete Insert for TEF 9964 24V 4210
Tool for Replacing Xenon Lamp in TEF 9964 Helideck Floodlight 4676