Transform QL014 User manual

UTILITY CABINET WITH STAINLESS-STEEL SINK AND FAUCET
ARMOIRE DE RANGEMENT AVEC ÉVIER EN ACIER INOXYDABLE ET ROBINET
ALL-IN-ONE
TOUT-EN-UN
OWNER’S MANUAL
MANUEL DE L’UTILISATEUR ITM. / ART. 2233579
QL014

2
ENGLISH
QL014
Table of Contents
Safety Information ..................................2
Warranty
One Year Limited Warranty...........................3
Warranty Claim Procedure...........................3
Pre-Installation
Tools/Materials Required ............................4
Parts Required ....................................4
Package Contents .................................5
Installation
Installing the Leveling Legs ..........................6
Installing the Handles ..............................7
Installing the Faucet ...............................8
Installing the Strainer ..............................9
Placement ......................................10
Drainage .......................................10
Supply Lines ....................................10
Maintenance
Cartridge Replacement ............................10
Care and Cleaning
Sink ...........................................11
Cabinet.........................................11
Service Parts......................................12
MANUEL DE L’UTILISATEUR ..........................13
Safety Information
READ AND SAVE THESE INSTRUCTIONS
1. Unpack and inspect this product for chips, scratches, cracks,
dents, and scuff marks. Do not install this product if any
damages or defects are identied.
2. Use this product only in the manner intended by the
manufacturer. If you have any questions, contact
the manufacturer.
3. Installation work and plumbing must be done by qualied
person(s) in accordance with all applicable codes and standards.
4. Protect the entire surface during installation.
DANGER: Always wear safety goggles and gloves in order
to avoid personal injury.

3 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Warranty
ONE YEAR LIMITED WARRANTY
A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or
damage that could have been discovered or avoided by proper inspection and testing prior to installation.
Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for one (1) year from the date of purchase.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Conglom Kitchen & Bath for all
warranty claims.
This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the
manufacturer’s instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen & Bath
replacement parts, (Replacement parts may be obtained by e-mail at [e-mail] or by calling 1-877-333-0098 between 8:30 am
- 5:00 pm EST) installation error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor, service
provider or member of the purchaser’s household). The warranty excludes damage due to aggressive air or water conditions, harsh or abrasive
cleaners and/or materials.
Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this
product. We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal
and installation of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or
replacement are the responsibility of the user.
Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective
under normal use and service during the warranty period.
Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable
items include, but are not limited to:
- Improper installation not in accordance with manufacturer’s instructions.
- Dents and/or scratches incurred during shipping, handling, or installation.
- Change in colour or nish due to chemical usage.
- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners.
- Alterations made to the unit by the purchaser or installer.
- Damage caused by accidental impact, re, ood, freezing, and normal wear.
- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.
- Damage caused by use of chlorine-based cleaners.
This warranty does not extend to commercial and institutional installation or use.
WARRANTY CLAIM PROCEDURE
If a claimable defect occurs or replacement parts are needed, please contact our customer service team at [e-mail] or 1-877-333-0098
(Service available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST).
Before you make your call, please ensure that you have:
- Model number or description.
- Proof of sale.
- Details regarding the defect and/or part number.
- Name(s) and address(es) of the owner and/or installer.

4
ENGLISH
QL014
Pre-Installation
TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)
Adjustable
wrench
Needle nose
pliers
Phillips
screwdriver
Utility knife Pipe wrench Sealant
Hacksaw Carpenter’s level Hex key
Safety gloves Safety goggles
PARTS REQUIRED (NOT SUPPLIED)
NOTE:
Parts not shown to actual size.
Tailpipe P-Trap Supply
lines Shims Wall Fastening Hardware

5 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Pre-Installation (continued)
PACKAGE CONTENTS
Carefully check the utility cabinet for damage and/or missing parts prior to installation. If there is any damage or if you are missing parts,
do not proceed with the installation. Report damage and/or missing parts immediately to our customer service team at cs@conglomkb.
com or 1-877-333-0098 (Service available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST). Please do not dispose of
packaging before you are satised with your new utility cabinet.
ABC
E
D
F
G
H
Part Description Quantity
A Cabinet 1
B Faucet 1
C Door Handles 2
D Leveling Legs 4
EStrainer Assembly 1
F Strainer Basket 1
G Handle Screws 4
H Leveling Leg Screws 16

6
ENGLISH
QL014
Installation
INSTALLING THE LEVELING LEGS
- Remove the cabinet (A) and place it on a soft,
protective surface.
- Attach each leveling leg (D) to the bottom of the cabinet (A)
using four of the provided screws (H).
- Gently rotate the cabinet (A) right side up.
WARNING: Always wear safety goggles and gloves
during installation.
CAUTION: Do not rest or bump the leveling legs on the side
as this may cause them to detach or break.
H
A
D

7 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Installation (continued)
INSTALLING THE HANDLES
C
G
- Attach door handles (C) to the cabinet doors using supplied door
handle screws (G) and a screw driver. Do not overtighten.
ADJUSTING THE DOOR POSITION
If the doors need to be repositioned, the hinges can be adjusted to ensure a
precise t with the cabinet.
1. The lateral adjustment screw adjusts the door orientation
from left to right.
2. The horizontal adjustment screw adjusts the door
orientation from front to back.
3. The vertical adjustment screw adjusts the orientation
up or down.
1
3
2

8
ENGLISH
QL014
Installation (continued)
INSTALLING THE FAUCET
Spray
Faucet
Head
Spray Head
Fitting
Spring
Quick
Connector
QUICK CONNECTOR
Main Water
Supply Outlet
Water Supply
Fitting
Screws
Main Water
Supply Outlet
Metal
Washer
Rubber
Gasket
Mounting
Shank
Sprayer Hose
Counterweight
Hot / Cold
Supply Lines
Supply Line
Inlet Fittings
Retaining
Nut
Faucet body
Quick
Connector
Sprayer Hose
Hose
Faucet outlet
- Remove the retaining nut, metal washer, and rubber gasket
from the mounting shank of the faucet.
- Insert the faucet hose and the mounting shank through the
faucet hole in the sink and rest the faucet on the sink.
- Install the rubber gasket, metal washer, and retaining nut
onto the mounting shank to secure the faucet to the sink.
Hand-tighten the retaining nut until it is snug. Tighten the
screws of the retaining nut using a screw driver. Do not
overtighten.
- Connect the main water supply outlet to the sprayer hose using
the quick connector as shown. Connect the end of the quick
connector marked with an “S” to the sprayer hose and the
other end to the main water supply hose of the faucet.
Lightly tug on the quick connect ttings to ensure they are
fully engaged.
- Fully retract the sprayer hose. Install the counterweight about
2 in. (50 mm) from the bottom on the side closest to the
sprayer head.
- Attach and hand tighten the supply lines (not supplied) onto
the faucet inlet ttings. Use two wrenches to tighten the two
ends together. Please note, tightening the ttings with a single
wrench may damage the faucet and void the warranty.
NOTE:
It is helpful to have a second person hold the faucet in place while
tightening the mounting nuts. Please ensure that none of the supply lines
are kinked during installation.

9 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Installation (continued)
INSTALLING THE STRAINER
- Apply plumbing putty or silicone sealant to the top side of
the drain opening.
- Insert the strainer body into the drain opening and press it
down until it is evenly seated.
- Assemble the rubber gasket, friction washer and strainer
locknut onto the strainer body from underneath the sink.
Hand tighten the strainer locknut until it is snug.
Do not overtighten.
- Insert the plastic ange into the ange-end of the tailpipe
(not supplied) then secure the tailpipe to the strainer body
using the connecting nut. Tighten the connecting nut until it
is snug. Do not overtighten.
- Remove excess sealant from around the drain opening.
NOTE:
The tail pipe is not supplied.
Strainer Body
Sealant
Sink
Rubber Gasket
Fiber Washer
Strainer Locknut
Plastic Flange
Tailpipe
Connecting Nut
Strainer Basket

10
ENGLISH
QL014
Installation (continued)
PLACEMENT
Push the cabinet against the wall. Level the unit by adjusting the four leveling legs and
checking the alignment of the sink using a carpenter’s level.
Please note, leveling feet are intended for leveling the cabinet, not height adjustments. It
is not recommended to extend leveling feet by more than 0.4” (10mm). Overextending the
leveling feet may render the sink cabinet unstable.
IMPORTANT: Due to the size and weight of this product, it must be rmly attached to the
wall using fastening hardware that is appropriate for your wall type. For drywall or plaster
walls, it must be attached to a wooden wall stud. Please consult a qualied installation
professional if necessary.
DRAINAGE
The tailpipe (not supplied) previously installed to the drain can now be connected to your
household plumbing. In some cases, your household plumbing will have to be modied
to ensure proper drainage. If so, please consult a licensed plumber to complete
needed modications.
SUPPLY LINES
Connect the supply lines to your home’s water supply as per manufacturer’s instructions.
Open the hot and cold water supply valves and check to make sure they have
been installed to appropriate inlet ports. Check for leaks. Run hot and cold water
uninterrupted for about one minute to remove any residue from the lines.
Cabinet Cross Section
Some Components Removed For Clarity
Wall Brace
Maintenance
CARTRIDGE REPLACEMENT
- Turn off the water supply to the faucet.
- Remove the setscrew cap. Loosen the setscrew with the hex
key provided and remove the handle.
- Gently unscrew the decorative cap by hand. Use a wrench to
unscrew the retaining nut.
- Pull the cartridge out of the faucet body and replace it with a
new ceramic cartridge. Ensure new cartridge is seated properly
with the locating pins in appropriate place.
- Secure the cartridge in place using the retaining nut.
- Gently tighten the retaining nut using a wrench.
Do not overtighten.
- Reinstall the decorative cap. Slide the handle back onto the
lever arm and make sure it rotates freely. Secure the handle in
place using the setscrew and cover it with the setscrew cap.
- Turn the water supply to the faucet back on.
- Operate the faucet to make sure everything works correctly.
Handle
Setscrew
Setscrew Cap
Faucet body
Cartridge Retaining Nut
Decorative Cap

11 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Care and Cleaning
Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care.
SINK CABINET
Do Do
- After use, always rinse your sink with tap water to dilute and
remove deposits.
- Towel dry after use whenever possible to prevent water
spots. Should water spots occur, clean with a mild solution
of vinegar and water followed by a thorough rinse.
- Use liquid soap, a general household cleaner, or a weak
solution of vinegar and water for regular cleaning.
- Only use plastic scouring pads recommended for use in
stainless-steel sinks, and only use them in the bowl of the
sink. Scrub in the direction of the satin nish lines.
- Remove dust and dry dirt with a soft, damp cloth.
- Clean grease, oil, paint and ink stains with isopropyl
(rubbing alcohol). Immediately rinse with water after
stain removal.
Do not Do not
- Do not allow any food, detergent, soap or grease to dry or sit
for extended periods of time on the surface of the sink.
- Never use abrasive cleaning products, as they will dull and
scratch the nish.
- Do not use scouting pads on the deck, as they will dull the
mirror nish.
- Never use steel wool pads, as they will leave iron particles
on the sink, which will cause corrosion.
- Never leave steel or cast iron pans in your sink for extended
periods of time, as this can cause corrosion.
- Never use chlorine-based cleaners in your new sink, they
could lead to rust spots and discolouration. If you must use
them, rinse sink thoroughly with fresh water immediately
after use. If any chemicals or glue make contact with the
sink during installation, wipe clean and rinse thoroughly
with fresh water.
- Do not allow your cabinet surface to come into contact with
products such as acetone (nail polish remover), nail polish,
dry cleaning solution, lacquer thinners, gasoline, pine oil, etc.
- Use caution when using sharp instruments that may fall and
scratch the surface.
SCRATCH, SPOT, AND BLEMISH REMOVAL AND SURFACE RESTORATION:
Little rust spots and blemishes that periodically appear in the sink are typically the result of the steel interacting with the chemicals
found in the vast spectrum of substances that sinks are commonly exposed to. They may also get transferred from other objects
placed or left in the sink. Scratches are the result of regular wear and tear.
To remove scratches, spots, and blemishes from the sink, rub them with a non-metallic scouring pad (e.g. Scotch-Brite®) combined
with a mild abrasive cleaner (e.g. Vim® or Barkeeper’s Friend®). Always rub the surfaces in the direction of the grain of the steel. When
nished, rinse the sink with water and dry it with a towel to allow the sink to form a protective outer layer. This procedure can also be
used to renew all of the surfaces of the sink.

12
ENGLISH
QL014
Service Parts
If you are missing parts or if you require replacement parts, please contact our customer service team at [e-mail] or 1-877-333-0098
(Service available in English and French, Monday - Friday from 8:30 am - 5:00 pm EST). Identify the required part(s) and have the part number(s) ready .
E F
A B C
D
H JG
Part Description Code Quantity
A Door Handles QHL182 2
B Door Handle Screws QHL104 4
C Leveling Leg Screws QHL106 16
D Leveling Legs QHL179 4
E Cabinet Hinges QHL102 4
F Ceramic Cartridge QHL166 1
G Sprayer Head QHL181 1
HStrainer Assembly QHL176 1
J Strainer Basket QHL177 1

Retain this manual for future use.
Imported by / Importé par :
St-Laurent, Québec, H4S 2C3
1-877-333-0098 | [email protected]
(service available in English and French, Monday - Friday from 8:30 am - 5 pm EST)
(service disponible en anglais et français, du lundi au vendredi, 8h30 à 17h, H.N.E.)
Made in China / Fabriqué en Chine