Transition Networks ARCNET C/AR-CF-01(SC) User manual

MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards ANSI/ATA 878
Delay 300ns one-way
Case dimensions 4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm)
Shipping Weight 2 pounds (0.9 kilograms)
Environment Temperature: 0-40°C (32° to 104° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty Five years
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing Media Converter Slide-in-Module(s) in the
Media Conversion Center. Failure to observe this caution could result in
damage to, and subsequent failure of, the Media Converter Slide-in-
Module(s).
NOTE: Media Converter Slide-in-Modules can be installed in any installation slot,
in any order.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
o part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the
radio interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
ARCNET is a registered trademark of Datapoint Corporation.
All registered trademarks and trademarks are the property of their respective owners. 33054.A
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE
NETWORK. Failure to observe this caution could result in damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
The TRANSITION Networks ARCNET®RJ-11 Copper/Fiber Media Converter (series
C/AR-CF-01), designed to be installed in the TRANSITION Networks Media Conversion
Center, E-MCC-1600, extends the signal distance of an ARCNET®segment or node
link up to 2 kilometers over fiber*, up to 100 meters over twisted-pair copper in a star topology,
and up to 120 meters over twisted-pair copper in a bus topology. A switch on the media
converter allows the media converter to terminate the link or node signal.
STATUS LEDS
Power Steady green LED indicates
connection to external AC
power.
UTP/STP Blinking green LED
indicates network traffic on unshielded or shielded twisted-pair link.
Fiber Blinking green LED indicates network traffic on fiber link.
*Consider carefully the network constraints imposed by the maximum latency
response time of installed equipment. Some equipment cannot handle the extended
response time that 2 kilometers of fiber introduces.
Minneapolis, MN 55344 USA
ARCNET®RJ-11 Copper/Fiber
Slide-In-Module Media Converters
C/AR-CF-01, C/AR-CF-01(SC), C/AR-CF-01(SM)
USER’S GUIDE
10BASE-T
RX
TX
Fiber
Power
UTP/STP
C/AR-CF-01
Provides an RJ-11 connector to twisted-
pair copper cable and a set of RX
(receive) and TX (transmit) ST connectors
to multimode fiber-optic cable.
C/AR-CF-01(SC)
Provides an RJ-11 connector to twisted-
pair copper cable and an RX (receive)
and TX (transmit) SC connector to
multimode fiber-optic cable.
C/AR-CF-01(SM)
Provides an RJ-11 connector to twisted-
pair copper cable and an RX (receive)
ST and TX (transmit) SC connector to
singlemode fiber-optic cable.
Power Modules
Media
Conversion
Center
E-MCC-1600
Power
In Use
Power
In Use
1
2
Manage ent
Module
Power
Link
TX
RX
Fiber
Multimode - to 2 kilometers
Singlemode - to 8 kilometers
UTP/STP
STAR - to 100 meters
(no minimum)
BUS - to 120 meters
(1.8 meter minimum

Installation NOTES
Install Slide-In-Module Media Converter
To install the Media Converter Slide-in-Module in the E-MCC-1600 chassis:
• Remove Media Converter Slide-in-Module protective plate from
selected installation slot by removing two screws that secure plate to
front of E-MCC-1600. Retain one installation screw.
• Carefully slide Media Converter Slide-in-Module into installation
slot, aligning Media Converter Slide-in-Module with installation
guides.
NOTE: Ensure that the Media Converter Slide-in-Module is firmly
seated against the backplane.
• Secure Slide-in-Module by installing retained installation screw.
Install Twisted-pair Copper
STAR TOPOLOGY
• MAXIMUM twisted-pair segment to active hub is 100 meters (300
feet); minimum does not apply.
BUS TOPOLOGY
• Devices attached to twisted-pair bus must be located AT LEAST six
(6) feet apart.
• MAXIMUM twisted-pair bus length is 120 meters (400 feet).
• Device(s) attached to EACH END of bus must be terminated. NOTE:
If the media converter is installed at one end of the bus, use the
configuration switch to terminate the media converter.
CONFIGURATION SWITCH
NOTE: Set configuration switch (located on the side of media converter)
according to site installation requirements:
Switch 1 NOT USED
Switch 2 UP = OFF Media converter TRANSFERS signal
DOWN = ON Media converter TERMINATES signal.
Install Fiber
Connect one end of first fiber cable to C/AR-CF-01 media converter TX
connector. Connect other end of that fiber cable to second C/AR-CF-01 media
converter RX connector. Connect one end of second fiber cable to C/AR-CF-01
media converter RX connector. Connect other end of that fiber cable to C/AR-
CF-01 media converter TX connector.
Power Slide-In-Module Media Converter
Locate correct power supply adapter for site installation. Connect media
converter power connector at end of power supply adapter cord to C/AR-CF-01
media converter power receptacle. Connect 2-prong or 3-prong external power
connector on other end of power supply adapter cord to external AC power.
CABLE SPECIFICATIONS
The physical characteristics of the cable must meet or exceed the following:
FIBER CABLE
MULTIMODE
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Wavelength: 850nM
Bit error rate: ≤10-9
Maximum Cable Distance: 2 kilometers
SINGLEMODE
Fiber Optic Cable Recommended: 9 µm singlemode fiber
Fiber Optic Transmitter Power: min: -27.0 dBm max: -17.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -13.0 dBm
Wavelength: 1300nM
Bit error rate: ≤10-9
Maximum Cable Distance: 8 kilometers
TWISTED PAIR CABLE
Category 3 wire or better is required; category 5 wire is recommended. Either
shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used. DO
NOT USE FLAT OR SILVER SATIN WIRE.
Category 3:
Gauge 24 to 22 AWG
Attenuation 28 dB/1000’ @ 10 MHz
Differential Characteristic Impedance 100 Ω±10% @ 10 MHz
Category 5:
Gauge 24 to 22 AWG
Attenuation 20 dB/1000’ @ 10 MHz
Differential Characteristic Impedance 100 Ω±10% @ 10 MHz
BUS TOPOLOGY
Minimum Node-Node Cable Distance: 1.8 meters (6 feet)
Maximum Cable Distance: 120 meters (400 feet)
Maximum Number of Nodes: 8
STAR TOPOLOGY
Minimum Cable Distance: 0 meters (0 feet)
Maximum Cable Distance: 100 meters (330 feet)
3
2
C/AR-CF-01
2
3
4
5
RJ-11
connector
Straight Through Cable
2
3
4
5
RJ-11
connector
NOTE: The active pair in a twisted-pair
copper ARCNET®-compliant network
are pins 3 & 4. Use only dedicated wire
pairs (such as blue/white & white/blue,
orange/white & white/orange) for the
active pins.