Transition Networks C/F-SM-MM-04(LH) User manual

COMPLIANCE INFORMATION
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
Copyright Restrictions
© 1997-2001 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Printed in the U.S.A. 33045.E
TRANSITION Networks C/F-SM-MM-04 series media converters, designed to be
installed in the TRANSITION Networks E-MCC-1600 Media Converter Chassis,
connect 850nm(SX) and 1300nm(LX) fiber in the full-duplex or half-duplex gigabit
(1000Mb/s ) Ethernet™ environment.
NOTE: In conformance with the
IEEE 802.3z standard, the 1300nm
singlemode fiber-optic connector
also can be used with 1300nm
multimode fiber-optic cable.
850nm/1300nm Gigabit Fiber
Slide-In-Module Media Converters
C/F-SM-MM-04, C/F-SM-MM-04(LH), C/F-SM-MM-04(LW)
USER’S GUIDE
Power Modules
Media
Conversion
Center
Power
In Use
Power
In Use
1
2
Management
Module
Power
Link
TX
RX
C/F-SM-MM-04
Provides an RX (receive) and TX
(transmit) SC connector to 850 nm
multimode fiber-optic cable and an RX
(receive) and TX (transmit) SC
connector to 1300 nm singlemode or
1300 nm multimode fiber-optic cable
C/F-SM-MM-04(LH) (long haul)
Provides an RX (receive) and TX
(transmit) SC connector to 850 nm
multimode fiber-optic cable and an RX
(receive) and TX (transmit) SC
connector to 1310 nm singlemode
fiber-optic cable
C/F-SM-MM-04(LW) (long wave)
Provides an RX (receive) and TX
(transmit) SC connector to 850 nm
multimode fiber-optic cable and an RX
(receive) and TX (transmit) SC
connector to 1550 nm singlemode
fiber-optic cable
C/F-SM-MM-04 in the Network . . . . .2
Installation . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . .4
Fault Isolation and Correction . . . . .5
Cable Specifications . . . . . . . . . . . . .6
Technical Specifications . . . . . . . . . .7
Compliance Information . . . . . . . . . .8

C/F-SM-MM-04 IN THE NETWORK
NOTE: This product is NOT a repeater. Therefore, maximum distances depend on
specific characteristics of the installation. The full distances of BOTH singlemode
and multimode fiber MAY NOT be supported in the same installation.
TECHNICAL SPECIFICATIONS
Standards IEEE 802.3u
Case Dimensions 4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm)
Shipping Weight 3 pounds (1.4 kilograms)
Environment Temperature: 0-40°C (32° to 104° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty Lifetime
DECLARATION OF CONFORMITY
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model: C/F-SM-MM-04 Series Media Converters
Part Number(s): C/F-SM-MM-04,C/F-SM-MM-04(LH), C/F-SM-MM-04(LW)
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the C/F-SM-MM-04 to which this declaration refers is
in conformity with the following standards.
EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_January 1, 1997_____
Stephen Anderson, Vice-President of Engineering Date
1300nm Fiber
850nm Fiber
1300nm Fiber
850nm Fiber
850nm Fiber

CABLE SPECIFICATIONS
The physical characteristics of the media cable must meet or exceed IEEE 802.3 specifications.
Gigabit Fiber Specifications
Bit error rate: ≤10-12
1300 NANOMETER (LX)
Fiber Optic Cable Recommended: 9 µm singlemode fiber
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Optional: 50 / 125 µm multimode fiber
C/F-SM-MM-04
Wavelength 1300 nm
Fiber-optic Transmitter Power: min: -13.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
(singlemode)
Minimum* Cable Distance: 2 meters
Typical Maximum* Cable Distance: 10 kilometers
(multimode)
Minimum* Cable Distance: 2 meters
Typical Maximum* Cable Distance: 550 meters**
C/F-SM-MM-04(LH) (long haul) (singlemode)
Wavelength 1310 nm
Fiber-optic Transmitter Power: min: -5.0 dBm max: -0.0 dBm
Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
Optical Budget 15.0 dB
Spectral Width 5.9 nm FWHM
Minimum Attenuation 3 dB
Typical Maximum* Cable Distance: 27 kilometers
C/F-SM-MM-04(LW) (long wave) (singlemode)
Wavelength 1550 nm
Fiber-optic Transmitter Power: min: -3.0 dBm max: -2.0 dBm
Fiber-optic Receiver Sensitivity: min: -23.0 dBm max: -3.0 dBm
Optical Budget 20.0 dB
Spectral Width 2.3 nm FWHM
Minimum Attenuation 5 dB
Typical Maximum* Cable Distance: 27 kilometers
850 NANOMETER (SX)
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Optional: 50 / 125 µm multimode fiber
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Minimum Cable Distance : 2 meters
Typical Maximum* Cable Distance: 220 meters for 160/500MHz•Km
270 meters for 200/500MHz•Km
*Actual distance dependent upon physical characteristics of network installation.
**Patchcord per IEEE 802.3 1998 edition specification may be required for
1300nm multimode cable.
INSTALLATION
Install Slide-In-Module in E-MCC-1600 Chassis
• Remove Media Converter Slide-in-Module protective plate from selected
installation slot by removing two (2) screw that secures plate to front of
E-MCC-1600.
• Carefully slide Media Converter Slide-in-Module into installation slot,
aligning Media Converter Slide-in-Module with installation guides.
NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated
against backplane.
• Secure Slide-in-Module by installing panel fastener screw attached to
Slide-in-Module.
Install Cable
NOTE: Be sure to connect correct speed fiber cable at each connector.
• Locate or build 802.3 compliant fiber cable with male two-stranded TX
to RX connectors appropriate to the media converter installed at both
ends.
• Connect male TX and RX cable connectors at one end of cable to TX
and RX female connectors, respectively, on media converter.
• Connect male TX and RX cable connectors at other end of cable to RX
and TX connectors of 802.3 compliant fiber device.

OPERATION
After installation, the media converter should function without operator
intervention.
Status LEDs
Use the status LEDs to monitor media converter operation in the network.
P(o)w(e)r Illuminated green LED indicates connection to external AC
power.
Link Steady green LED indicates that fiber link is connected
properly.
FAULT ISOLATION and CORRECTION
If the media converter fails, isolate and correct the failure by determining the
answers to the following questions and then taking the indicated action:
1. Is the power LED on the media converter illuminated?
NO • Is the power adapter the proper type of voltage and cycle frequency
for your AC outlet? NOTE: Refer to the “Power Supply
Requirements” on the back page.
• Is the power adapter properly installed in the media converter and
in the outlet?
• Contact Technical Support at [phone]/ (800) LAN-WANS.
YES • Proceed to step 2.
2. Is the multimode fiber Link LED illuminated?
NO • Check fiber cables for proper connection.
• Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on the other device.
• Power-cycle the media converter.
• Refer to Tech Tips available at: http://www.transition.com
• Contact Technical Support at [phone]/ (800) LAN-WANS.
YES • Proceed to step 3.
3. Is the singlemode fiber Link LED illuminated?
NO • Check fiber cables for proper connection.
• Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on the other device.
• Power-cycle the media converter.
• Refer to Tech Tips available at: http://www.transition.com
YES • Contact Technical Support at [phone]/ (800) LAN-WANS.