Transition Networks SGETF1013-110 User manual

*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation.
Note: The chassis version of the media converter is CGETF10xx-11x. For more
information, see the CGETF10xx-1xx user’s
guide on-line at: www.transition.com.
User’s Guide
SGETF10xx-1xx
Stand-Alone Media Converter
•Gigabit Ethernet
• Copper to Fiber
• 1000Base-T to 1000Base-SX/LX
Transition Networks SGETF10xx-1xx Gigabit
Ethernet media converter connects 1000Base-T
shielded or unshielded twisted-pair copper cable to
1000Base-SX or 1000Base-LX, fiber-optic cable.
The SGETF10xx-1xx is a stand-alone media
converter
Installation . . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . . . . .9
Technical Specifications . . . . . . . . . .11
Troubleshooting . . . . . . . . . . . . . . .12
Contact Us . . . . . . . . . . . . . . . . . . .13
Compliance Information . . . . . . . . .15
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
SGETF1013-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-SX, 850 nm multimode
220 m (721 ft)* (62.5/125 µm cable)
550 m (1,804 ft)* (50/125 µm cable)
SGETF1014-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 nm single mode
10 km (6.2 miles)*
SGETF1015-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 nm single mode
25 km (15.5 miles)*
SGETF1017-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1550 nm single mode
65 km (40.4 miles)*
SGETF1024-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-SX, 1310 nm extended
multimode, 2 km (1.2 miles)*
Note: 62.5/125 µm (fiber only)
SGETF1035-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1550 nm single mode
125 km (77.5 miles)*

2
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Part Number Port One - Copper Port Two - Single Fiber-Optic
SGETF1029-110 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 TX/1550 RX
single mode, 20 km (12.4 miles)*
SGETF1029-111 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1550 TX/1310 RX
single mode, 20 km (12.4 miles)*
SGETF1029-112 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 TX/1550 RX
single mode, 40 km (24.8 miles)*
SGETF1029-113 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1550 TX/1310 RX
single mode, 40 km (24.8 miles)*
SGETF1029-116 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1510 TX/1590 RX
single mode, 80 km (49.7 miles)*
SGETF1029-117 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1590 TX/1510 RX
single mode, 80 km (49.7 miles)*
The SGETF1029-11x and the SGETF1029-11x are to be installed in
the same network, where one is the local converter and the other
is the remote converter.
* Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation (TX = transmit, RX = receive).
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note: Third-party Multi-Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can also be used in the SGETF1040-110.
Sold separately, the following SFP transceiver modules for port two are compatible
with the SGETF1040-110 converter and are available from Transition Networks.
SGETF1040-110 Descriptions
TN-SFP-SX LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*
TN-SFP-SXD LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*
TN-SFP-LX1 LC, 1000Base-LX, 1310 nm single mode, 10 km (6.2 miles)*
TN-SFP-LX3 LC, 1000Base-LX, 1310 nm single mode, 30 km (18.8 miles)*
TN-SFP-LX5 LC, 1000Base-LX, 1550 nm single mode, 50 km (31.2 miles)*
TN-SFP-LX8 LC, 1000Base-LX, 1550 nm single mode, 80 km (50.0 miles)*
TN-SFP-LX12 LC, 1000Base-LX, 1550 nm single mode, 120 km (74.6miles)*
Part Number Port One - Copper Port Two - Single Fiber-Optic
SGETF1040-110 RJ-45 1000Base-T
100 m (328 ft)*
Open slot for SFP modules
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
Installation
Set the 6-position switch
The 6-position switch is located on
the side of the media
converter.
• Use a small flat blade
screwdriver to set the
recessed switches.
• All switches are shown in the
default position, UP.
Note: Switch positions S2 and S3 work together to configure the media converter
for Pause conditions.
S1 Remote-Fault Detection
up Disabled
down Enable
S2 & S3 work in combination
Pause
10 sw position 2 up and 3 down: Symmetric
01 sw position 2 down and 3 up: Asymmetric
11 sw positions 2 and 3 up: Pause is OFF (default position) 00 sw positions 2
and 3 down: Symmetric and Asymmetric
S4 Transparent Link Pass-Through
up Enable Link Pass-Through
down Disable Link Pass-Through
S5 Fiber Auto-Negotiation
up Disable Fiber Auto-Negotiation for the fiber link
(default setting)
down Enable Fiber Auto-Negotiation for the fiber link
S6 Loop Back
up Disable RX/TX signal loop back (default setting)
down Enable RX/TX signal loop back
2. Pause (symmetric)
3. Pause (asymmetric)
4.Transparent Link Pass-Through
5. Auto-Negotiation
1
. Remote Fiber Fault Detect
6. Loop Back

4
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Installation -- Continued
Install Mode
During installation, set converter DIP switch 4 DOWN; leave all other switches in
the UP position (default). This disables Transparent Link Pass-Through and Auto-
Negotiation, allowing individual copper and fiber links to be established (both copper
port LEDs will turn ON with each device-to-device connection) independent of a complete
end-to-end connection.
Operation Mode
After installation is complete (all copper and fiber ports connected and linked), set all
switches to the UP position (default)).
Fiber Auto-Negotiation
Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the
supported features of the remote device; this occurs only when a fiber cable is
connected to a device with a negotiating port. The process is as follows:
1. The fiber interface detects the supported features of the remote partner.
2. These abilities are passed to the twisted-pair interface and advertised.
3. Once the twisted-pair interface has a link at the highest common capability, it
passes the result to the fiber interface.
4. The fiber interfaces then start advertising these capabilities. At this point, the
link between the fiber and the negotiating port is complete.
If the SGETF10xu-1xu is connected via fiber to another SGETF10xu-1xu, both media
converters must have the Fiber Auto-Negotiation setting disabled (switch 5 UP).
Note: Transparent Link Pass-Through (switch position 4 enabled) cannot be turned
OFF (disabled) when Fiber Auto-Negotiation is ON (enabled).
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Installation -- continued
Install the fiber cable
1. Locate a 1000Base-SX/LX compliant fiber cable with male, two-stranded TX
to RX connectors installed at both ends.
2. Connect the fiber cables to the SGETF10xx-1xx media converter as
described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter, hub, etc.)
as described:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
RX
TX TX
RX
Device Device

6
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Installation -- Continued
Install the copper cable
1. Locate a 1000Base-T compliant copper cables with male, RJ-45 connectors
installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the SGETF10xx-1xx media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port
on the other device (switch, workstation, etc.).
RJ-45 port
on the other device
(switch, work station, etc
.)
RJ-45 port
on the media
converter
Power the media converter
AC
The external power supply provided with this device is UL listed by the
manufacturer of the power supply.
1. Install the power adapter cord to the back of the media converter.
2. Connect the power adapter plug to AC power.
3. Verify that the media converter is powered by observing the illuminated LED
power indicator light.
DC
Consult the user’s guide for the Transition Networks SPS1872-xx DC external
power supply for powering the media converter.
Power Connector
Converter Rear Panel
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
Operation
Status LEDs
Use the status LEDs to monitor the SGETF10xx-1xx media converter operation in
the network.
PWR (Power) ON = Connected to external AC power.
LKF (Fiber link) ON = Fiber Connection
RXC (Copper receive) Flashing = Receiving data on the copper link.
ON = Copper Link connection
Duplex ON = Full
Remote-Fault Detect
Remote fiber fault detect (RFD) monitors the status of the fiber link. RFD must
only be enabled on the remote converter. If RFD is enabled in the device at each
end of the link, a link pass-through event will put the converters into an
unrecoverable state (unable to establish a link).
Pause
The pause feature can improve network performance by allowing one end of the
link to signal the other to discontinue frame transmission for a set period of time
to relieve buffer congestion.
The pause feature can be set to one of four settings:
• Disable (i.e., no pause)
• Symmetrical pause
• Asymmetric TX (transmit) pause
• Asymmetric RX (receive) pause
Enable the pause feature if it is present on ALL network devices attached to the
media converter(s); otherwise, disable the pause feature.
AutoCross (always on)
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-X)
cables to be used when connecting to 10Base-T, 100Base-TX, or 1000Base-T
devices, such as hubs, transceivers, or network interface cards (NICs). AutoCross
determines the characteristics of the cable connection and automatically configures
the unit to link up to its companion device regardless of the cable configuration.
LKF PWR
RXTX
1000Base-X 1000Base-T
Duplex LEDRXC LED

8
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Operation - Continued
Link Pass-Through
The Link Pass-Through feature allows the media converter to monitor both the
fiber and copper RX (receive) ports for loss of signal. Refer to the illustration
below. For example, in the event of a loss of an RX signal (1), the media converter
will automatically disable the fiber TX (transmit) signal (2), thus, “passing through”
the link loss (3). The far-end device is automatically notified of the link loss (4),
which prevents the loss of valuable data unknowingly transmitted over an invalid
link.
Transparent Link Pass-Through
Transparent Link Pass-Through operates similar to Link Pass-Through with one
exception: the fiber link between the converters remains active. A signal is passed
through to the remote converter, causing it to shutdown the copper link, notifying
the end device of the link failure.
Auto-Negotiation
Auto-Negotiation enables automatic configuration to achieve the best possible
mode of operation over a link between devices. A device with this feature enabled
will broadcast its speed (10Mbs, 100Mbs, etc.) and duplex (half/full) capabilities to
another device with this feature, then negotiate the best mode of operation
between them—no user intervention required.
Fiber Auto-Negotiation
Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the
support abilities of the remote device. It is supported only when the fiber is
connected to a device with a negotiating port.
Loop Back
This diagnostic feature enables the media converter to loop back the signal from
the RX port to the TX port for testing and troubleshooting purposes. Test signals
from a bit-error test unit can then be inserted into either the copper or fiber link
to test a particular segment.
This type of diagnostic test can only be performed from the local to the remote
device with loop back enabled on the remote device.
SNMP
Note: SNMP is not supported in the SGETF10xx-1xx converters.
4
1
Media
Converter A Media Converter B
Near-End
Device Far-End Device
original fault
on the co
pp
er link
media converter B
disables the co
pp
er lin
k
media converter A
disables the fiberTX link
3
2
media converter B
loses the fiber RX link
[email protected] -- Click the “Transition Now” link for a live Web chat. 9
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber cable
Bit Error Rate: <10-9
Single mode fiber (recommended): 9 µm
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
SGETF1013-110 850 nm multimode
Fiber Optic Transmitter Power: min: -10.0 dBm max: -4.0 dBm
Fiber Optic Receiver Sensitivity: min: -17.0 dBm max: 0.0 dBm
Link Budget: 7.0 dB
SGETF1014-110 1310 nm single mode
Fiber-optic Transmitter Power: min: -9.5 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
Link Budget: 10.5 dB
SGETF1015-110 1310 nm single mode
Fiber-optic Transmitter Power: min: -5.0 dBm max: -0.0 dBm
Fiber-optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm
Link Budget: 19.0 dB
SGETF1017-110 1550 nm single mode
Fiber-optic Transmitter Power: min: -3.0 dBm max: 2.0 dBm
Fiber-optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm
Link Budget: 21.0 dB
SGETF1024-110 1300 nm extended multimode
Fiber-optic Transmitter Power: min: -10.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -17.0 dBm max: -3.0 dBm
Link Budget: 7.0 dB
SGETF1035-110 1550 nm single mode
Fiber-optic Transmitter Power: min: 0.0 dBm max: 5.0 dBm
Fiber-optic Receiver Sensitivity: min: -27.0 dBm max: -3.0 dBm
Link Budget: 27.0 dB
SGETF1029-110 1310nm TX / 1550nm RX single mode
SGETF1029-111 1550nm TX / 1310nm RX single mode
Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm
Link Budget: 13.0 dB

10
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Cable Specifications -- Continued
Fiber cable - Continued
SGETF1029-112 1310nm TX / 1550nm RX single mode
SGETF1029-113 1550nm TX / 1310nm RX single mode
Fiber-optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm
Fiber-optic Receiver Sensitivity: min: -23.0 dBm max: -3.0 dBm
Link Budget: 20.0 dB
SGETF1029-116 1510nm TX / 1590nm RX single mode
SGETF1029-117 1590nm TX / 1510nm RX single mode
Fiber-optic Transmitter Power: min: -2.0 dBm max: +3.0 dBm
Fiber-optic Receiver Sensitivity: min: -26.0 dBm max: -3.0 dBm
Link Budget: 24.0 dB
Copper cable (Category 5 -- minimum requirement)
• Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz
• Straight-through OR crossover cable may be used.
• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used
• All pin pairs (1&2, 3&6, 4&5, 7&8) are active in a gigabit network.
• Use only dedicated wire pairs for the active pins; e.g., blue/white & white/blue,
orange/white & white/orange, etc.
• Do not use flat or silver satin wire.
[email protected] -- Click the “Transition Now” link for a live Web chat. 11
Technical Specifications
For Transition Networks’ Model SGETF10xx-1xx or equivalent
Standards: IEEE 802.3ab™, IEEE 802.3 2000
Data Rate / Delay: 1000 Mbs/300 nsec
Dimensions: 3.25" x 0.1" x 4.8" (82mm x 25mm x 122mm)
Weight: 3 oz. (91 g) approximately
Power Supply 12VDC @ 0.8A (minimum)
Power Consumption: 5.4W, 450mA @ 12VDC
Packet Size: 10 Kbytes (maximum)
MTBF* 382,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
1,345,000 hours (Bellcore7 V5.0)
Operating Temp: Tmra** 0°C to 50°C (32°F to 122°F)
Storage Temp: -15°C to 65°C (5°F to 149°F)
Humidity: 10% to 90%, non condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
*MTBF is estimated using the predictability method. This method is based on MIL-217F at 25°C
ambient temperature, typical enclosure heat rise of 10°C, and nominal operating conditions and
parameters. Installation and configuration specific MTBF estimates are available upon request.
Contact Technical Support.
**Manufacturer’s rated ambient temperature.
For the most up-to-date information on the SGETF10xx-1xx media converter, view the user’s
guide on-line at: www.transition.com.
The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-
825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view
the beam directly with optical instruments. Failure to observe this warning could result in an eye
injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than those
specified herein may result in hazardous radiation exposure.
IMPORTANT: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422,
RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building (inside plant)
link segments that are not subject to lightening transients or power faults. Copper-based media
ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc.,
are NOT to be connected to inter-building (outside plant) link segments that are subject to
lightening transients or power faults.

12
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Troubleshooting
If the media converter fails, isolate and correct the fault by determining the answers
to the following questions and then taking the indicated action:
1. Is the PWR (power) LED illuminated?
NO
• Is the power adapter the proper type of voltage and cycle frequency for
the AC outlet?
• Is the power adapter properly installed in the media converter and in the
outlet?
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the RXC (copper link) LED illuminated?
NO
• Check the twisted-pair copper cables for proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Is the LKF (fiber link) LED illuminated?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the media converter are connected
to the RX and TX ports, respectively, on the other device.
• If the media converter is connected to another SGETF10xx-1xx using
fiber, verify the fiber Auto Negotiate is disabled (DIP-switch 5 in the UP
position).
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 4.
4. Is the RXC (copper receive) LED flashing?
NO
• If there is activity on the 1000Base-T port, disconnect and reconnect the
twisted-pair copper cable to restart the initialization process.
• Restart the workstation to restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
13
[email protected] -- Click the “Transition Now” link for a live Web chat.
Contact Us
Technical support
Technical support is available 24-hours a day
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343, U.S.A.
telephone: [phone]
toll free: 800-526-9267
fax: [phone]

14
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Declaration of Conformity
Name of Mfg: Transition Networks
10900 Red Circle Drive Minnetonka MN 55343 U.S.A.
Model: SGETF10xx-1xx Series Media Converters
Part Number(s): SGETF1013-110, SGETF1014-110, SGETF1015-110,
SGETF1017-110, SGETF1018-110, SGETF1024-110,
SGETF1035-110, SGETF1040-110, SGETF1029-110,
SGETF1029-111, SGETF1029-112, SGETF1029-113,
SGETF1029-116, SGETF1029-117
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the SGETF10xx-1xx to which this declaration refers is in
conformity with the following standards:
EN 55022:1994 + A1:1995 + A1:1997; EN 55024:1998 + Al:2001 + A2:2003
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
August, 2008___
Stephen Anderson, Vice-President of Engineering Date
[email protected] -- Click the “Transition Now” link for a live Web chat. 15
Compliance Information
CE Mark
FCC regulations
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set
out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
European regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses
Gerätes Rundfunkstörungen auftreten. In diesem Fäll is der Benutzer für Gegenmaßnahmen
verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures
spécifiques appropriées.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
In accordance with European Union Directive 2002/96/EC of the European
Parliament and of the Council of 27 January 2003, Transition Networks will accept
post usage returns of this product for proper disposal. The contact information
for this activity can be found in the 'Contact Us' portion of this document.

Printed in the U.S.A. 33334.G
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions
© 2003-2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means
- graphic, electronic or mechanical - without written permission from Transition Networks.
16
SGETF10xx-1xx