Transition Networks M/GE-PSW-PSE-01 User manual

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 1of 16
M/GE-PSW-PSE-01
Mini Fast / Gigabit Ethernet PoE+ Media Converter
(1) 10/100/1000Base-T PoE+ RJ-45 Port + (1) 100/1000Base-X SFP Slot
User Guide
33830 Rev. B

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 2of 16
Cautions and Warnings
Cautions indicate that there is the possibility of poor equipment performance or potential damage to the equipment. Warnings indicate
that there is the possibility of injury to person.
Cautions and Warnings appear here and may appear throughout this manual where appropriate. Failure to read and understand the
information identified by this symbol could result in poor equipment performance, damage to the equipment, or injury to persons.
Cautions : While installing or servicing the power module, wear a grounding device and observe all electrostatic discharge
precautions. Failure to observe this caution could result in damage to, or failure of the power module.
Warning: Do not connect the power module to an external power source before installing it into the chassis. Failure to observe this
warning could result in an electrical shock, even death.
WARNING: Equipment grounding is vital to ensure safe operation. The installer must ensure that the power module is properly grounded
during and after installation. Failure to observe this warning could result in an electric shock, even death.
WARNING: A readily accessible, suitable National Electrical Code (NEC) or local electrical code approved disconnect device and branch-
circuit protector must be part of the building's installed wiring to accommodate permanently connected equipment. Failure to observe this
warning could result in an electric shock, even death.
WARNING: Turn any external power source OFF and ensure that the power module is disconnected from the external power source before
performing any maintenance. Failure to observe this warning could result in an electrical shock, even death.
WARNING: Ensure that the disconnect device for the external power source is OPEN (turned OFF) before disconnecting or connecting the
power leads to the power module. Failure to observe this warning could result in an electric shock, even death. See Electrical Safety
Warnings for Electrical Safety Warnings translated into multiple languages.
M/GE-PSW-PSE-01 Mini Fast / Gigabit Ethernet PoE+ Media Converter User Guide, 33830 Rev. B
Record of Revisions
Rev.
Date
Description
A
5/6/21
Initial release at FW 24228A_RC1, PCB 11639 Rev 1A, 11638 Rev1A and power supply 25173.
B
5/19/21
Update power supply connector information and remove powered chassis references.
Trademarks : All trademarks and registered trademarks are the property of their respective owners.
Copyright Notice/Restrictions : Copyright © 2021 Transition Networks. All rights reserved. No part of this work may be
reproduced or used in any form or by any means (graphic, electronic or mechanical) without written permission from
Transition Networks. Printed in the U.S.A.
Contact Information
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: [phone] | toll free: 1.800.526.9267 | fax: [phone]
[email protected]om |techsup[email protected] |[e-mail]

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 3of 16
Contents
Cautions and Warnings.................................................................................................................................................2
Record of Revisions.......................................................................................................................................................2
Introduction ..................................................................................................................................................................3
Ordering Information....................................................................................................................................................4
Features ........................................................................................................................................................................4
Feature Descriptions.....................................................................................................................................................4
Active Link Pass Through (ALPT) ...............................................................................................................................4
Auto Power Reset .....................................................................................................................................................5
Auto-Negotiation ......................................................................................................................................................5
Auto-MDI/MDIX........................................................................................................................................................5
Specifications and Standards........................................................................................................................................6
Installation ....................................................................................................................................................................7
Installation Overview................................................................................................................................................7
Mounting Options.....................................................................................................................................................7
Operation......................................................................................................................................................................8
Status LEDs................................................................................................................................................................8
LED Descriptions .......................................................................................................................................................9
Compliance Information.............................................................................................................................................10
Declaration of Conformity ......................................................................................................................................10
Product Views .............................................................................................................................................................10
Power Supply ..............................................................................................................................................................12
25173 Commercial Power Supply...........................................................................................................................12
25173 Features ...................................................................................................................................................12
25173 Specifications ...........................................................................................................................................12
25173 Mechanical Drawing ................................................................................................................................15
Troubleshooting..........................................................................................................................................................16
Contact Us...................................................................................................................................................................16
Introduction
The Transition Networks M/GE-PSW-PSE-01 Gigabit Ethernet Stand-alone Mini Media Converter provides cost
effective media conversion between 10/100/1000Base-T ports and 100/1000Base-SX/LX ports. With its fixed
configuration, deployments are just plug-and-play, and its small size makes it ideal for locations where space is
limited. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, but it also
provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber.
In addition to providing copper to fiber conversion, this converter is also classified as Power Sourcing Equipment
(PSE), meaning it combines data received over the fiber optic link with 56VDC input power to provide power and
data to a Powered Device (PD) over the twisted Pair cable, while complying with the IEEE 802.3af and IEEE 802.3at
PoE+ standards. This allows the user to take advantage of the benefits of fiber cabling, along with the benefits of
Power-over-Ethernet (PoE) technology.
Supporting PoE allows this converter to send data and power to devices like VoIP Phones, Security Cameras, and
Wireless Access Points, especially if they must be located in remote areas of your network that can only be
reached with fiber optic cabling.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 4of 16
Ordering Information
SKU
Description
M/GE-PSW-PSE-01
(1) 10/100/1000Base-T PoE+ RJ-45 port [100 m/ 328 ft.] to (1) 100/1000Base-X SFP slot
(empty). Includes Power Supply 25173. Note: Cannot be used with M-MCR-01 or E-MCR-
05 Racks due to power limitations.
Optional Accessories (sold separately)
SFP/SFP+ Modules
See our SFP Products page (sold separately)
WMBM
Wall Mount Bracket for MiniConverters (sold separately)
DRBM
DIN Rail Mount Bracket for MiniConverters (sold separately)
RMBM
Rack Mount Bracket for MiniConverters, use with RMS19-SA4-02 (sold separately)
Power Supply included: to order the corresponding country specific power supply, add the extension below to the
end of the SKU. For example: M/GE-PSW-PSE-01-NA = North America, -LA = Latin America, -EU = Europe,
-UK = United Kingdom, -SA = South Africa, -JP = Japan, -OZ = Australia, and -BR = Brazil.
Features
•Wall mount, DIN Rail, or table top installation
•External AC/DC power supply included with country specific power cord
•2-port 10/100/1000 copper to fiber media conversion with IEEE 802.3at PoE+ on the copper port
•Supports full 30 Watts of power to the twisted pair port
•SFP slots can support any 100Base-FX or 1000Base-X fiber SFP module
•Supports Auto-Negotiation and Auto-MDI/MDIX
•Supports Active Link Pass Through (ALPT)
•Supports Auto Power Reset
•Jumbo frame support
•8K MAC address table
•LEDs indicators for power status, Link/Activity per port, PoE status/classification, APR state
•Plug-and-Play fixed configuration, no DIP switches
•Over-current protection, Under-current protection, and Fault protection input
Feature Descriptions
Active Link Pass Through (ALPT)
The ALPT (Active Link Pass Through) function is a feature that disables Link Pass Through after the device has first
powered up. ALPT allows the user to see the link status with only one media connected (either the Fiber or the
Copper link). Once both media ports have established link or are active at the same time, the converter will
automatically enable its Link Pass Though feature. The LPT feature now enabled will monitor the link status of
each port. If either port’s link status changes to down, the converter will disable the other port to indicate to the
end device that the link partner is no longer communicating. The ALPT feature is permanently enabled. A power
cycle to the device will disable the LPT feature again until both links are established.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 5of 16
Auto Power Reset
The Automatic Power Reset (APR) feature is enabled after the device has been powered for one minute and the
ALPT feature is enabled. When both of these conditions are met, whenever the fiber link goes down due to the
fiber partner link status or the ALPT forwarded copper link partner status. The converter will detect that the fiber
link is down, disable the POE power for 5 seconds, and then allow the PSE to re-start power negotiation with a PD
(powered device).
After an APR event the converter will lock out the power reset feature for five minutes to allow time for the PD
device to fully boot and re-establish link. When the five minute timeout is complete and the Fiber link has been
re-established, the APR functions will begin monitoring for the next fiber link down event.
Circled in red above is the location of LED 4 that can be seen inside the metal. LED 4 will turn solid green when the
APR function is enabled and is monitoring the fiber link.
Auto-Negotiation
The Auto-Negotiation feature is permanently enabled.
Auto-MDI/MDIX
The Auto-MDI/MDIX feature is permanently enabled.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 6of 16
Specifications and Standards
Spec
Description
Standards
IEEE 802.3-2012, IEEE 802.3af/at PSE-PoE, IEEE 802.3ab, IEEE 802.3z, IEEE
802.3x, IEEE 802.3az
Switch Features
Max Packet Size 10,000 bytes
Max MAC Addresses 8k
1Mbit shared buffer memory
Dimensions
Width: 1.8” [46 mm] x Height: 0.85" [22 mm] x Depth: 3.3” [85 mm]
Power Consumption
34W with full IEEE 802.3at 30 Watt load
Power Supply Connector
Standard 2.5 mm barrel
Power-over-Ethernet
Max PoE Budget: 30 Watts
Environment
Operating Temp: 0°C to +40°C (with included power supply)
Storage Temp: -40°C to +85°C
Operating Humidity: 5% to 95% (non-condensing)
Altitude: 0 –10,000 ft.
Weight
2 lbs. (0.9 kg) (complete package)
4.17 oz. (118 g) (converter alone)
MTBF
M/GE-PSW-PSE-01 only: 2,941,024 hours (Telcordia SR-332)
Included Power Supply only (25173): 159,357 hours (MIL-DHBK-217F)
Certifications
EN55032-2012 Class A, IEC 61850-3:2002,
EN55024-2010, CE Mark, Power Supply is UL listed
Warranty
Lifetime
Data speed
TP: 10/100/1000Mbps
SFP: 100FX/1000X. SGMII not supported on this product
DIP Switches and Jumpers
None; all features are permanently enabled
Certifications
EN55032-2012 Class A, IEC 61850-3:2002,
EN55024-2010, CE Mark, Power Supply is UL listed
The M/GE-PSW-PSE-01 is an 802.3at device; it will only provide power on one pair. Highlighted in yellow below is
the M/GE-PSW-PSE-01 pinout.
PSE Pinout Alternatives:
Conductor
Alternative A (MDI-X)
Alternative A (MDI)
Alternative B (All)
1
Negative VPSE
Positive VPSE
2
Negative VPSE
Positive VPSE
3
Positive VPSE
Negative VPSE
4
Positive VPSE
5
Positive VPSE
6
Positive VPSE
Negative VPSE
7
Negative VPSE
8
Negative VPSE
Note: All PD devices must accept power on either pair (Alternative A or Alternative B).

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 7of 16
Installation
Warning: Do not attempt to open the enclosure or service the power supply. Opening the enclosure may cause
serious injury or death. There are no user replaceable or serviceable part in thus device.
Installation Overview
Mount the Media Converter in its final location; see ‘Mounting Options’ below.
Perform Grounding procedure.
Insert SFP.
Install and connect the fiber cable.
Install and connect the copper cable.
Power up the media converter.
Check LED status.
Mounting Options
WMBM: 3.3” Wall Mount Bracket for Mini Media Converters:
DRBM: 3.3” DIN Rail Mount Bracket for “Mini” Media Converters:
RMBM: Rack mount bracket for mini media converters, used with RMS19-SA4-02:

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 8of 16
Operation
Status LEDs
When the module has been installed and configured, verify the converter is operational by viewing the LEDs.
The Power LED indicates the module is receiving power.
The Fiber status LED indicates the fiber optic connection has been established.
The RJ-45 TP status LEDs indicate the speed of the RJ-45 port connection.
The PoE status LED indicates the module has established a successful detection of a PD and is supplying
Power over Ethernet.
LED 4 can be seen inside the metal. LED 4 will turn solid green when the APR function is enabled and is
monitoring the fiber link. LED 4 is circled in red below. See the Auto Power Reset description above.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 9of 16
LED Descriptions
LED
Description
Two-up Bi-Color
LEDs
Top LED - TP Status:
•Green = Gigabit
•Amber = 100 or 10 speeds.
•Off = no link
•There is no indication for duplex
Bottom LED - Fiber Status:
•100FX TP Link/Activity: Yellow On = Link. Yellow Blinking = Activity
•1000X TP Link/Activity: Green On = Link. Green Blinking = Activity
Power LED
Green ON = power applied to board
PoE Status LED
When powering an 802.3af PD: Yellow = On
When powering an 802.3af PD over-load or short: Yellow Blinking at 1Hz
Vin under-voltage or IC over-temp: Yellow Blinking at 4Hz
When powering an 802.3af PD: Green = On
When powering an 802.3af PD over-load or short: Green Blinking at 1Hz
APR Status LED
inside enclosure
•Solid green: APR is armed and ready to reset power to the POE Power from the
PSE port when the fiber link status goes to the down state.
•Blinking green: APR is not ready; waiting for timeout or fiber link to be re-
established.
Note: The TP-L/A Act 1000 and SFP-L/A Act 1000 flash green because this converter has MAC Learning disabled,
so whenever a packet is received on one port, that packet will always be repeated on the other port. This
functionality causes the Activty LED for BOTH ports to ALWAYS flash in unison, even for unidirectional traffic.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 10 of 16
Compliance Information
Declaration of Conformity
Product Views

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 11 of 16

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 12 of 16
Power Supply
The M/GE-PSW-PSE-01 uses Power Supply 25173.
25173 Commercial Power Supply
The 25173 AC/DC desktop power supply offer 40 watts of output power with
an IEC-320-C8 AC inlet.
The 25173 has a rated input voltage of 100-240VAC, and is designed to meet
Energy Star Ver. 2.0, DoE Level VI, and ErP STEP2. It has over-voltage and
over-current protection and UL, cUL, CB, CE, FCC, RCM, BSMI, IRAM, and CCC
safety approvals.
25173 Features
•Rated Input Voltage 100-240 VAC
•40 Watts Max
•Single Output
•Designed to meet Energy Star Ver. 2.0, DoE Level VI, and ErP STEP2
•IEC 320-C8 AC inlet
•ROHS Compliant
•Over-voltage and over-current protection
•UL, cUL, CB, CE, FCC, RCM, BSMI, IRAM, and CCC Safety Approvals
25173 Specifications
All specifications are based on 25⁰C, Nominal input Voltage, and Maximum Output Current unless otherwise
noted. We reserve the right to change specifications based on technical advances.
Dimensions: 4.45 in. x 1.93 in. x 1.38 in. (113 mm x 49 mm x 35 mm)
Input Specifications
Specification
Min.
Typ.
Max.
Unit of
Measure
Rated Input Voltage
100
240
VAC
Normal Line Input
115VAC/60Hz, 220VAC/50Hz
Input Frequency
47
63
Hz
Input Current (full load)
2.0
A
Input Fuse (Input Hot line side must be fused)
Rating (3.15A/250V)
Inrush Current @ 110VAC, cold start, max load
< or = 80
A
Inrush Current @ 220VAC, cold start, max load
< or = 160
A

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 13 of 16
Output Specifications
Specification
Min.
Typ.
Max.
Unit of
Measure
Output Voltage
56
VDC
Regulation
53.2
58.8
VDC
Line Regulation
± 1
%
Dynamic Load Regulation
± 5
%
Voltage Tolerance
± 5
%
Output Power
40
W
Output Current
0
0.71
A
Ripple and Noise
720
mV
No Load Power Consumption
0.1
W
Hold-Up Time
≥8.3
mSec.
Rise Time
≤ 50
mSec.
Turn-On Time
3
Seconds
Protection
Specification
Min.
Typ.
Max.
Unit of
Measure
Over Current Protection
110
200
%
Over Voltage Protection
175
%
Environmental Specifications
Specification
Min.
Typ.
Max.
Unit of
Measure
Operating Temperature
0
40
⁰C
Storage Temperature
-20
85
⁰C
Operating Humidity
10
90
%
Storage Humidity
5
90
%
Temperature Rise (Optional)
45
⁰C
Altitude (Operation and Non-operation)
Sea Level
5000
M
Stability
2
%
MTBF (MIL-HDBK-217F, 25⁰C)
100,000
Hours

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 14 of 16
General Specifications
Specification
Min.
Typ.
Max.
Unit of
Measure
Efficiency
≥ 87.59
%
IR
≥ 50
MΩ
Leakage Current
≥ 500
uA
Voltage Isolation: DC ground may be separated from AC neutral and AC line.
Insulation Test: Between primary and secondary circuit: 500VDC, 2 Sec.
Configuration: Line, Neutral: 2-Wire, AC Input.
Hi-Pot Test: Between primary and secondary circuit: 3000VAC/4242VDC, 3mA 2 Sec.
Drop Out: Output voltage should remain in specified range, through the absence of line input during ½ cycle, at
full load and normal AC line input.
Physical Specifications
Weight: 10.58 Oz (300 Gr.)
Dimensions: 4.45 in x 1.93 In. x 1.38 In. (113mm x 49mm x 35mm)
Enclosure Material: 94V-0 Minimum
Output Cable: UL2468#20
Safety Characteristics
Safety Approvals
UL, CUL, CB, CE, FCC, RCM, BSMI, IRAM, CCC
EMI
CISPR 32, EN 55032
FCCP Part 15
Class B
Class B
ESD
IEC 61-000-4-2
Contact: ±4kV
Air: ±8kV
RS
IEC 61-000-4-3
Frequency: 80~1000MHz
Field Strength: 3V/M, 80% AM (1KHz)
EFT
IEC 61-000-4-4
1.0KV on Input Power Ports
Surge
IEC 61-000-4-5
Line to Line: ±1kV (peak)
Efficiency
Energy Star Ver. 2.0, DoE Level VI,
ErP STEP2
Notes
1. Specifications subject to change without notice.

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 15 of 16
25173 Mechanical Drawing

Transition Networks M/GE-PSW-PSE-01 User Guide
33830 Rev. B https://www.transition.com Page 16 of 16
Troubleshooting
1. Make sure the function you are trying to perform is supported on this device; see “Features” on page 4.
2. Verify the install procedure was followed properly; see “Installation” on page 7.
3. Check the front panel LEDs; see “Status LEDs” on page 8 and “LED Descriptions” on page 8.
4. Ensure that the power supply is correctly connected; see “Power Supply” on page 12. If the power LED is
blinking, it may indicate incorrect or faulty power supply, or that the power adapter is not the proper type of
voltage and cycle frequency for the AC outlet.
5. Make sure attached devices (SFP, WAP, IP camera, etc.) are installed properly and operating correctly; see the
attached device’s documentation.
6. Verify that the TX and RX cables on the converter are connected to the RX and TX ports, respectively, on the
other device.
7. Record device information (see below)
8. Contact Transition Networks Technical Support (see below).
Problem: The Auto Power Reset feature only works once after cold boot; subsequent tries to get the feature to
power-cycle a PD fail to cut the PD's power.
Description : There is about a 5 minute time out set on this feature to prevent constant power cycling of the PD,
due to the boot time of some PD devices taking a couple of minutes.
Solution : Wait for a couple of minutes for the PD device to boot.
Contact Us
Technical Support: Technical support is available 24-hours a day:
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Main Office
tel: [phone] | toll free: 1.800.526.9267 | fax: [phone]
[email protected]om | techsup[email protected] | [e-mail]
Address
Transition Networks
10900 Red Circle Drive
Minnetonka, MN 55343, U.S.A.
Web: https://www.transition.com