Transition Networks CSETF1011-205 User manual

User’s Guide
CSETF10xx-205
Slide-in-Module Media Converter
• Ethernet and Fast Ethernet
• 10/100Base-TX to 10/100Base-SX
Transition Networks CSETF10xx-205 series
Ethernet and Fast Ethernet media converters
connect 10/100Base-TX twisted-pair copper cable
to 10/100Base-SX fiber-optic cable. The
CSETF10xx-205 is also designed to be installed in
a Transition Networks PointSystem™ chassis.
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network installation.
The stand alone version of this media converter is SSETF10xx-205. For more
information, see the SSETF10xx-205 user’s guide on-line at: www.transition.com.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .4
Cable Specifications . . . . . . . . . . .7
Technical Specifications . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . .9
Contact Us . . . . . . . . . . . . . . . . .11
Compliance Information . . . . . . .12
Part Number Port One - Copper
10/100Base-TX
Port Two - Fiber-Optic
10/100Base-SX
CSETF1011-205 RJ-45
80 m (262 ft)*
ST, 850 nm multimode
2 km (1.2 mi.)* @ 10 Mb/s
60 m (197ft.)* @ 100 Mb/s
CSETF1013-205 RJ-45
80 m (262 ft)*
SC, 850 nm multimode
2 km (1.2 mi.)* @ 10 Mb/s
60 m (197 ft.)* @ 100 Mb/s

2
CSETF10xx-205
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Install the Slide-In-Module
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the media converter. Failure to observe this
caution could result in damage to, and subsequent failure of, the media
converter.
To install the CSETF10xx-205 media converter slide-in-module:
1. Locate an empty installation slot on the PointSystem™ chassis.
2. Carefully slide the slide-in-module into the installation slot, aligning the
module with the installation guides.
3. Ensure that the module is firmly seated inside the chassis.
4. Push in and rotate the attached panel fastener screw clockwise to secure
the module to the chassis front.
CFMFF100 CFMFF100
CETCF100 CFETF100
CFMFF100
SPD PWR
FRX
CRX
FLNK
CLNK
100BASE-TX
RX
TX
100BASE-FX
LinkAlert
ED
050½
LA PWR
RXF
RXC
LNK
COL
LKS
PWR
LKM
10BASE-2
10BASE-FL
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I
0
TERM
INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
I
0
PWR
SX
10
TX
100ACT
panel fastener screw
Installation
Set the Jumper
• The jumper is located on the circuit board.
• Use small needle-nose pliers to set the jumper.
Hardware The media converter settings such as
AutoCross and Link Pass-Through cannot be
changed.
Software The media converter settings are determined
by the most-recently saved, on-board
microprocessor settings. Software Mode
Hardware Mode
SH
SH
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
Installation -- Continued
Installing the Cable
Fiber
1. Locate or build 10/100Base-SX compliant fiber cable with male, two-
stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the CSETF10xx-205 media converter as
described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
Connect the fiber cable
to the media converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
Copper
1. Locate or build 10/100Base-TX compliant copper cables with male, RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the CSETF10xx-205 media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter

4
CSETF10xx-205
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
Power the Media Converter
The CSETF10xx-205 slide-in-module is powered through the Transition Networks
PointSystem™ chassis.
Operation
Status LEDs
Use the status LEDs to monitor the CSETF10xx-205 media
converter operation in the network.
PWR Power On = Connection to the external
AC or DC power.
SX-ACT Fiber Activity Flashing = Data reception on the
fiber link.
SX-100 Fiber Speed On = Fiber link at 100 Mb/s.
SX-10 Fiber Speed On = Fiber link at 10 Mb/s.
TX-ACT Copper Activity Flashing = Data reception on the
copper link.
TX-100 Copper Speed On = Copper link at 100 Mb/s.
TX-10 Copper Speed On = Copper link at 10 Mb/s.
PWR
SX
10
TX
CSETF205
TX
100ACT
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Operation -- Continued
Product Features
Link Pass-Through
The Link Pass-Through feature allows the media converter to monitor both the
fiber and copper RX (receive) ports for loss of signal. In the event of a loss of
an RX signal (1), the media converter will automatically disable the TX
(transmit) signal (2), thus, “passing through” the link loss (3). The far-end
device is automatically notified of the link loss (4), which prevents the loss of
valuable data unknowingly transmitted over an invalid link.
4
1
Media
Converter A
Media
Converter B
Near-End
Device
Far-End
Device
original fault
on the copper link media converter B disables the copper lin
k
media converter A
disables the fiber TX link
3
2
media converter B
loses the fiber RX link
Auto-Negotiation
The Auto-Negotiation feature allows the media converter to automatically
configure itself to achieve the best possible mode of operation over a link.
The media converter broadcasts its speed (10 Mb/s or 100Mb/s) and duplex
capabilities (full or half) to the other devices and negotiates the best mode of
operation. Auto-Negotiation allows quick and easy installation because the
optimal link is established automatically. No user intervention is required to
determine the best mode of operation.
A scenario where the media converter is linked to a non-negotiating device is
a case where the user may want to disable Auto-Negotiation. (Note: Auto-
Negotiation can only be disabled in software mode.) In this instance, the
mode of operation will drop to the least common denominator between the
two devices (e.g.: 10 Mb/s, half-duplex). Disabling this feature gives the user
the ability to force the connection to the desired speed and duplex mode of
operation.
NOTE: The CSETF10xx-205 series media converter does not support rate
conversion between 10Mb/s and 100Mb/s network devices.

6
CSETF10xx-205
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Operation -- Continued
Product Features -- Continued
AutoCross™
The AutoCross feature allows either straight-through (MDI) or crossover (MDI-
X) copper cables to be used when connecting to 10/100Base-TX devices.
AutoCross determines the characteristics of the connection and automatically
configures the unit to link up, regardless if the copper cable is MDI or MDI-X
configuration.
NOTE: Factory default is “enable AutoCross.” Transition networks
recommends leaving the device in the “enable” mode.
SNMP
Use SNMP at an attached terminal or at a remote location to monitor the
media converter by monitoring:
• Media converter power
• Copper link status
• Fiber link status
• Copper receive status
• Fiber receive status
• Media converter speed
Also, use SNMP to enter network commands that:
• Enable/disable AutoCross, Link Pass-Through, Auto-Negotiation
• Media converter speed
• Power down the media converter
See the on-line documentation that comes with Transition Networks
FocalPoint™ software for commands and usage at www.transition.com
Crossover Cable
1
2
3
6
Straight-Through Cable
Twisted Pair #1
Twisted Pair #1
Twisted Pair #2
Twisted Pair #2
1
2
3
6
1
2
3
6
1
2
3
6
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
Cable Specifications
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Bit Error Rate: <10-9
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
Wavelength: 850 nm multimode
Attenuation: <3.75 dB/km @ 850 nm
CSETF1011-205 (100 Mb/s)
Fiber Transmitter Power: min: -19.0 dBm max: -9.0 dBm
Fiber Receiver Sensitivity: min: -24.0 dBm max: -8.0 dBm
Link Budget: 5.0 dB
CSETF1011-205 (10 Mb/s)
Fiber Transmitter Power: min: -19.0 dBm max: -9.0 dBm
Fiber Receiver Sensitivity: min: -32.5 dBm max: -8.0 dBm
Link Budget: 13.5 dB
CSETF1013-205 (100 Mb/s)
Fiber Transmitter Power: min: -19.0 dBm max: -9.0 dBm
Fiber Receiver Sensitivity: min: -24.0 dBm max: -8.0 dBm
Link Budget: 5.0 dB
CSETF1013-205 (10 Mb/s)
Fiber Transmitter Power: min: -19.0 dBm max: -9.0 dBm
Fiber Receiver Sensitivity: min: -32.5 dBm max: -8.0 dBm
Link Budget: 13.5 dB
The fiber optic transmitters on this device meet Class I Laser safety requirements
per IEC-825/CDRH standards and comply with 21 CFR1040.10 and
21CFR1040.11.
Copper Cable
Category 5:
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB /100m @ 100 MHz
Maximum Cable Distance: 80 meters
• Straight-through (MDI) or crossover (MDI-X) twisted-pair cable may be used.
• Shielded (STP) or unshielded (UTP) twisted-pair cable may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.

8
CSETF10xx-205
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model CSETF10xx-205 or equivalent.
Standards: IEEE 802.3™
Data Rate: 10 Mb/s, 100 Mb/s
Dimensions: 3.4" x 0.87" x 5" (86 mm x 22 mm x 182 mm)
Weight: 3 oz (91 g) (approximately)
Power Consumption: 3.6 watts
MTBF 521,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
1,450,000 hours (Bellcore7 V5.0)
Environment: Tmra*: 0° to 60°C (32° to 140°F)
Storage Temperature: -20° to 85°C (-4° to 185°F)
Humidity: 5 to 95%, non condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
*Manufacturer’s rated ambient temperature: Tmra range for this slide-in-module
depends on the physical characteristics and the installation configuration of the
Transition Networks PointSystem™ chassis in which this slide-in-module will be
installed.
The information in this user’s guide is subject to change. For the most up-to-date
information on the CSETF10xx-205 media converter, view the user’s guide on-
line at: www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare into
the beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
CAUTION: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be
connected to intra-building (inside plant) link segments that are not subject to
lightening transients or power faults. Copper based media ports, e.g., Twisted
Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are
NOT to be connected to inter-building (outside plant) link segments that are
subject to lightening transients or power faults.
9
[email protected] -- Click the “Transition Now” link for a live Web chat.
Troubleshooting
1. Is the PWR LED on the media converter illuminated?
NO
• Is the media converter inserted properly into the chassis?
• Is the power cord properly installed in the chassis and in the
grounded AC outlet?
• Does the grounded AC outlet provide power?
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 2.
2. Is the SX-ACT LED illuminated?
NO
• Check the 10/100Base-SX (fiber) cables for proper connection.
• Verify that the TX and RX cables on the media converter are
connected to the RX and TX ports, respectively, on the other device.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 3.
3. Is the SX-ACT LED flashing?
NO
• If there is no activity on the fiber port, continue below
• If there is activity on the fiber port, disconnect and reconnect the
fiber cable to restart the initialization process.
• Restart the workstation to restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 4.
4. Is the SX-100 LED illuminated?
YES (Flashing)
• The media converter is selecting between 10 Mb/s and 100 Mb/s
speed for the fiber link. If persistent, disconnect and reconnect either
cable to restart the initialization process.
• Go to step 5.
YES
• The media converter has selected 100 Mb/s operation for the fiber
link. If this is not the correct speed, disconnect and reconnect the
fiber cable to restart the initialization process.
• Go to step 5.
NO
• Go to step 5.
5. Is the SX-10 LED illuminated?
YES (Flashing)
• The media converter is selecting between 10 Mb/s and 100 Mb/s
speed for the fiber link. If persistent, disconnect and reconnect either
cable to restart the initialization process.

10
CSETF10xx-205
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
YES (On)
• The media converter has selected 10 Mb/s operation for the fiber
link. If this is not the correct speed, disconnect and reconnect the
fiber cable to restart the initialization process.
• Go to step 6.
NO
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
6. Is the TX-ACT LED illuminated?
NO
• Check the 10/100Base-TX (copper) cables for proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 7.
7. Is the TX-ACT LED flashing?
NO
• If there is no activity on the copper port, go to step 8.
• If there is activity on the copper port, disconnect and reconnect the
copper cable to restart the initialization process.
• Restart the workstation to restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Go to step 8.
8. Is the TX-100 LED illuminated?
YES (Flashing)
• The media converter is selecting between 10 Mb/s and 100 Mb/s
speed for the copper link or one or both of the links is down. If
persistent, disconnect and reconnect either cable to restart the
initialization process.
• Go to step 9.
YES (On)
• The media converter has selected 100 Mb/s operation for the copper
link. If this is not the correct speed, disconnect and reconnect the
copper cable to restart the initialization process.
• Go to step 9.
NO
• Go to step 9.
9. Is the TX-10 LED illuminated?
YES (Flashing)
• The media converter is selecting between 10 Mb/s and 100 Mb/s
speed for the copper link or one or both of the links is down. If
persistent, disconnect and reconnect either cable to restart the
initialization process.
YES
• The media converter has selected 10 Mb/s operation for the fiber
link. If this is not the correct speed, disconnect and reconnect the
copper cable to restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
[email protected] -- Click the “Transition Now” link for a live Web chat. 11
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 U.S.A.
Model: CSETF10xx-205 Series Media Converters
Part Number(s): CSETF1011-205, CSETF1013-205
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the CSETF10xx-205 to which this declaration refers is in
conformity with the following standards.
EN55022:1994 + A1:1995 + A2:1997; EN 55024:1998
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
July, 2007____
Stephen Anderson, Vice-President of Engineering Date
Contact Us
Technical Support
Technical support is available 24 hours a day.
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition Now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-Based Seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, U.S.A.
telephone: [phone]
toll free: 800-526-9267
fax: [phone]

Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2004 - 2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any
means - graphic, electronic, or mechanical - without written permission from Transition
Networks.
Printed in the U.S.A. 33290.D
Compliance Information
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A & B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A & B limits for radio noise for digital
apparatus set out on the radio interference regulations of the Canadian Department of
Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la Class A & B prescrites dans
le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du
Canada.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Dew Anschluss dieses Grates an en öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung Dew
Richtlinie 91/263/EWG zur Angleichung Dew Rechtsvorschriften Dew Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich Dew gegenseitigen Anerkennung ihrer
Konformität.
In accordance with European Union Directive 2002/96/ECU of the European
Parliament and of the Council of 27 January 2003, Transition Networks will
accept post usage returns of this product for proper disposal. The contact
information for this activity can be found in the 'Contact Us' portion of this
document.