Transmitter Solutions PAL SPIDER WIEGAND 26 User manual

1. Package Contents
PAL SPIDER DEVICE
4G Antenna (1) 433 Mhz Antenna (1)
PAL Spider
Wireless Wiegand
Controller
Quick Start Guide
Download the user manual here:
Power - PAL requires a 12-24V DC transformer. PAL reaches 30mA at
maximum power consumption.
3. Power Connection
A
NOTE: the + and – power inputs can be wired
to either power input on the PAL board, they
are interchangeable
12 - 24V DC
Transformer
2. Mounting Controller
Mounting - When mounting the PAL be sure the RFID antenna is
pointing as close to vertical as possible. For the best signal strength.
The 4G antenna needs to be pointing to the right
Note: When mounting the PAL unit inside a gate operator,
use external antenna (PALANT3G
4. Network Connection/Account Setup
Network Connection - The PAL SIM card must be
activated before installation of the PAL Spider. In order
for PAL Unit to work properly, There must be a reliable
AT&T Network signal at the location of the PAL
installation.
Signal Level - Once powered on, the PAL will go through an automatic network boot up. After
60-seconds if working properly the PAL device will have a solid LED light on the Network and one
of the signal LED's.
A company account on portal.pal-es.com is required to register the PAL device. If you do not
currently have a company account call us at 866-975-0101. Use your login credentials to login
to the PAL home page.
Meaning
Action
Fast flashing of the SIM light
Slow flashing of the SIM light
2 blinks and break
4 Short flash of the SIM
Sim LED is stable
Signal light No. 1 is on
Signal light No. 2 is on
Signal light No. 3 is on
System is booting
Searching for a cellular network
connecting to the Internet process
Connecting to the PAL interface
System ready
Low signal
Good signal
Very good signal
LEDs key
https://transmittersolutions.com/wp-content/uploads/2023/10/Spider-User-Manual-Ver-1.3-FINAL-8-28-2023.pdf
SIM CARD LOCATION
4G
2.4 Ghz
433 Mhz
2.4 Ghz
4G
SIM
433 Mhz
2.4 Ghz
4G
SIM
433 Mhz
SIM
2.4 Ghz
4G
SIM
433 Mhz

A
A
B
5. PAL Registration 6. Wiegand Connection
WEB PORTAL USER MANUAL
THE PAL CONTROLLER MUST BE
ADDED THROUGH THE PAL
ONLINE WEB PORTAL BEFORE
USING THE PHONE APP
Request web portal login information.
A
B
C
D
E
Login to your account at portal.pal-es.com
select devices on the left hand side and click
add on the top right hand corner.
Enter the serial number and code found on
the back of the PAL unit. Click Save.
You can now select the device for
configuration and management.
For more detailed management and
configuration instructions please refer
to the PAL full web portal user manual.
transmittersolutions.com/wp-content/uploads/2019/04/PAL-web-usermanualENG-v1.pdf
GND
D0
D1
LED
When wiring in a wiegand device to the PAL controller, use DO, D1, and
wiegand GND from the wiegand device to the PAL controller.
When wiring card reader LED to correspond with relay, wire to N.O.-1.
A
Door or Gate Position switch - Mount this
on the door frame or on the gate in the
desired location with the wire running to the
input on the PAL controller, like shown above.
When using two door or gate position sensors
for double doors wire them in series with one
leg of each switch running back to the
controller for connection.
Maglock
Optional
Magnetic
Sensor
Installation allows you
to receive a gate status
notification
INPUT 1 GND N.C.1 COM 1 N.O. 1 12VDC
7. Maglock Connection
Input voltage
12VDC / 3A
Maximum load
2A/30VDC; 0.5A/125VAC
8. Electric Strike Connection
A
A
Door or Gate Position switch - Mount this
on the door frame or on the gate in the
desired location with the wire running to the
input on the PAL controller, like shown above.
When using two door or gate position sensors
for double doors wire them in series with one
leg of each switch running back to the
controller for connection.
Optional
Magnetic
Sensor
Installation allows you
to receive a gate status
notification
Input voltage
12VDC / 3A
Electric Strike
Maximum load
2A/30VDC; 0.5A/125VAC
2.4 Ghz
4G
SIM
433 Mhz
2.4 Ghz
4G
SIM
433 Mhz
2.4 Ghz
4G
SIM
433 Mhz

General – Allows you to configure
the relay output hold time.
Timer Events – Allows for setting a
7-day automatic unlock/open,
lock/close schedule.
Time Groups – Allows for creating
groups to restrict Wiegand and
phone application access to the
PAL controller.
A
B
C
A
B
COnce you have clicked “add” you will enter
the main user screen. Fill out the necessary
information and click save. Note: If you enter
a phone number the user can download the
“Palgate” phone application and will be able
to trigger the gate or door from their phone.
Leaving the phone number section blank will
not allow the user to have app control of the
PAL unit.
Once in users click “add” in the top right hand
corner. (You can also import complete
databases, please call technical support or
see full instruction manual for detailed
instructions on this)
From the Home screen go to devices. Select
the device you wish to add users to. Once in
the device main menu select users. (for sites
with multiple PAL units installed please call
technical support 866-975-0101 or refer to
complete manual)
9. Adding Users 10. PAL Settings
11. User Credentials - Bluetooth vs cellular
In this image you will see that the
"Nearby Only" box is checked. This
enables a Bluetooth Credential, so that
the user has to be in close proximity to
the gate in order to open it.
Leaving this box unchecked allows a user
to open the gate from anywhere via a
cellular signal.
12. PAL 4-Button Transmitter Programming
Each PAL Spider Controller includes a PAL 4-button
Transmitter. This transmitter can be programmed by:
1. Choose the Spider unit from the "Devices" section
2. Click on "Settings"
3. Click on the "Remote Control"
You will then see the menu below:
Buttons are designated
1-4 starting at the top and
going clockwise around
the remote.
You can program all 4
buttons to the relay of a
single PAL Spider; or if
you have multiple Spider
units, each button can be
programmed to a
different Spider Unit.