Travis Industries 564 HO DancingFyre User manual

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 1 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Packing List
The log set includes:
Rear Log
Left Log
Right Log
Left Twig
Right Twig
Center Twig
Installation Tips
If using propane (LP), convert the appliance before installing the burner.
Installation Warnings
The logs are fragile, especially after being exposed to heat.
Make sure the gas control valve is OFF and the heater is cool before servicing.
Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
The burner must be correctly positioned before installing the logs. Make sure the burner is
fully seated and the pilot is properly aligned.
Intake Restrictor
Log Spacers
Fireback Floor
Burner Support Bracket
Burner
Rear Fireback Side Firebacks
LS-43 Log Kit
Rockwool
Embers
Grate Assembly
Andiron Clips

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 2 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Andiron Clips
NOTE: Two andiron clips are included for those installations using andirons. See directions below to install.
Figure 1: Andiron Clips Installation
5/32 Hex
Wrench
11/32" Nutdriver
a
b
c

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 3 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Burner Installation
1. Remove both accent light assemblies from the brackets at the rear of the firebox (save the screws).
Place the accent light assemblies in the center of the firebox floor, as shown below.
NOTE: Do not touch the bulbs.
Figure 2: Accent light bracket screws location
Figure 3: Accent lights placed on firebox floor
2. Install the intake restrictor as shown below, using the existing screws on the rear wall of the firebox.
Set the intake restrictor to the correct setting for the vent configuration. See the installation manual for
details.
Figure 4: Intake restrictor installed, showing location of screws

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 4 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
3. Install the burner support bracket at the left side of the firebox, as shown below.
Figure 5: Burner support bracket screws location Figure 6: Burner support bracket installed
4. Install the fireback floor into the firebox, as shown below.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 5 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
5. Install the rear, left, and right firebacks as shown below.
Replace the fireback clips shown in step “a” after installing the firebacks.
Remove the clip located on the
firebox ceiling near the front (both
sides). The side fireback clip has
a keyhole slot. It can be removed
by loosening the screw and
sliding the clip out.
a
1/4” Nutdriver

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 6 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
6. Re-attach the accent lights to the brackets at the rear of the firebox.
Figure 7: Accent lights screws location Figure 8: Accent lights attached
7. Install the burner inside the firebox. Make sure the burner is fully seated and level with the fireback floor.
8. Install the grate into the firebox as shown below.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 7 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
9. Install the logs into the firebox, following the instructions below.
Log Installation
Log Spacers Placement
1. Place the right log spacer on the burner as shown below.
2. Place the rear log spacers on the burner as shown below.
Rear Log Placement
3. Place the rear log on the rear log spacer with the cut-outs over the two pins, as shown below.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 8 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Left Log Placement
4. Place the left log as shown below, with the two holes in the bottom fitting over the pin on the burner and
metal bracket attached to the pilot assembly.
Right Log Placement
5. Place the right log on the front right log spacer as shown below. The right log has two holes in the bottom
that fit over the two pins on the burner.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 9 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Left Twig Placement
6. Place the left twig as shown below, with the twig pointing toward the center of the firebox. The left twig
has a single hole on the bottom that fits over the pin on the rear log.
Right Twig Placement
7. Place the right twig as shown below, with the twig pointing toward the center of the firebox. The right twig
has a single hole on the bottom that fits over the pin on the rear log.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 10 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Center Twig Placement
8. Place the center twig directly on the burner as shown below. Make sure it does not cover any burner holes.
Rock Wool Installation
9. Place the included rock wool on top of the burner to enhance the glow from the burner.
NOTE: The rock wool works best when it is applied in a very thin, porous layer. The best method for
applying the rock wool is to brush it on to the burner. Compress a clump of rock wool between your thumb
and forefinger. Use a stiff brush to apply a thin layer of rock wool fibers onto the burner. Do not use the
entire bag of rock wool. Use only a small amount and save the remainder. Over-use of rock wool will
diminish the glow and may cause sooting or other adverse conditions.

564 HO DancingFyre Burner
Installation Instructions (sku: 96900114)
Page 11 of 11 17601661 — 9/22/11 © Travis Industries, Inc.
Ember Placement
10. Place a layer of embers along the edges of the burner, rivets, and fireback floor to enhance the aesthetics
of the firebox. Do not place embers over any burner holes. See the photos below.