Travis Industries DVL Ember-Fyre User manual


DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 1 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Compatibility
•DVLGSRNBInsert
•DVLGS(AU)Inbuilt
Packing List
•DVLEmber‐FyreBurnerAssembly
•6‐PieceLogSet
•
BagofEmbers
•BagofRockWool
Burner Installation
1. Access the firebox.
2. Leave the air shield in place for NG (natural gas). Remove and discard the air shield for LP (propane).

3. Install the burner. Install the side ember trays.
NOTE: Make sure the burner is fully seated over the orifices (the burner should be aligned all the way to
the right).

NG LP


DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 2 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Log Set Installation
! The logs are fragile, especially after being exposed to heat.
•Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service.
•Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
•If using propane (LP), convert the appliance before installing the logs.
•The burner must be correctly positioned before installing the logs. Make sure the burner is fully
seated and the pilot is properly aligned.
Right Log Bracket
Bendthelogbracketupto90°asshownbelow.
 
Rear Log Placement
Therearloghastwoobroundholesonthebottom.Placethelogsothepinsontheburnerinsertintothe
holesonthelog(seephotosbelow).Onceinplace,carefullypullthelogallthewayforward.Thisallowsthe
logtoglowabovetherearburnerholes.NOTE:Ifyouencountersootingontherearlog,movethelogback
untilsootingiseliminated.


DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 3 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Left Log Placement
Theleftloghasaholeonthebottom.Placethelogsothepinontheburnerinsertsintotheholeonthelog
(seephotosbelow).Positionthelogsotherightsidestraddlestheburnerholes.Thelogmustnotcoverany
burnerholes.
Right Log Placement
Therightloghasaholeonthebottom.Placethelogsobothburnerpinsinsertintotheholesonthelog(see
photosbelow).Makesurethelogispushedbacksoitsitsflat.


DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 4 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Left Twig Placement
Thelefttwighastwoholesinthebottomthatfitoverthepinsonthebackandleftlog(seephotosbelow).
Placethetwigasshownbelow.
Right Twig Placement
Therighttwighasoneholeinthebottomthatfitsoverthepinonthebacklog(seephotobelow).Thebottom
ofthelogrestsontherightlog.Placethelogasshownbelow.



DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 5 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Front Ember Chunk Placement
Placetheemberchunkasshowninthephotosbelow.Makesuretheemberchunksdoesnotcoverany
burnerholes.
Ember Placement
Abagofembersisincludedwithyourburnerkittoenhancethefirebox.Placealayerofembersalongthe
edgesoftheburner,ontopofscrew‐heads,andalongtheperimetertoenhancetheaestheticsofthefirebox.
Donotplaceembersoveranyburnerholes.Seethephotobelow.Placealayerofembersalonganyvisible
edgesoftheburner.


DVL Ember-Fyre Burner
Installation Instructions (SKU96900107,96900109)

Page 6 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.
Rockwool Installation
Theincludedrockwoolisplacedontopoftheburnertoenhancetheglowfromtheburner.Therockwool
worksbestwhenitisappliedinaverythin,porouslayer.Thebestmethodforapplyingtherockwoolisto
brushitontotheburner.Compressaclumpofrockwoolbetweenyourthumbandforefinger.Useastiff
brushtoapplyathinlayerofrockwoolfibersontotheburner.Donotusetheentirebagofrockwool.Use
onlyasmallamountandsavetheremainder.Over‐useofrockwoolwilldiminishtheglowandmaycause
sootingorotheradverseconditions.
 
