Travis Industries DVS GSR User manual


DVS GSR Dancing-Fyre Burner
Installation Instructions (SKU96900103)


Page 1 of 4 17601694.docx — 9/25/18 © Travis Industries, Inc.

Makesuretohavethemediakitandfirebacks(ifused)availableatthetimeof
installation.Componentsfromthemediakitareusedduringburnerinstallation.
Compatibility
DVSGSRNBInsert DVSGSNB(AU)Inbuilt
Packing List

Left&RightEmberTrays(wscrews)





AirDeflector

BurnerAssembly
Order of Installation

IfusingLP(Propane),converttheappliancepriortoinstallingtheburner(seeowner’smanual).
DriftwoodLogSet(94500571)orFyre‐StonesSet(94700762)

WhenusingDriftwoodorFyre‐Stonesmedia,notethattheonlycompatiblefirebacksare
stainlesssteelorenamel.
a)Removetheglassframe.
b)Disabletheaccentlight(seeinstructionsonpage4).
c)Installtheburner(seeinstructionsonpage3).
d)Attachtheairdeflector(seeinstructionsonpage4).
e)Installthefirebacks(ifused).
f)Installthemedia(seeinstructionsincludedwiththemediakit).
TraditionalLogSet(94500991)*
a)Removetheglassframe.
b)Installtheburner(seeinstructionsonpage3).
c)Attachtheairdeflector(seeinstructionsonpage5).
d)Installthefirebacks(ifused).
e)Installthemedia(seeinstructionsincludedwiththemediakit).
*NOTE:IfusingtheTraditionalLogSetwithstainlesssteel,enamel,orblackglassfirebacks,youwill
needtoconductthefollowingorderofinstallation:
a) Removetheglassframe.
b) Attachtheairdeflector(seepage5).
c) Bendtheaccentlightdown.
d) Installtherearfireback.
e) Bendtheaccentlightup.
f) Installtheburner.
g) Installthesidefirebacks.
h) Installthemedia.



DVS GSR Dancing-Fyre Burner
Installation Instructions (SKU96900103)


Page 2 of 4 17601694.docx — 9/25/18 © Travis Industries, Inc.
Burner Installation
Attachtheembertraystotheburnerasshownbelow.Thescrewsareshippedpre‐attachedtothe
embertrays.

Installtheburnerassemblyasshownbelow.
NOTE:Makesuretheburnerisfullyseatedovertheorifices.Thepilothoodshouldbeslightlyabove
theburnersurfaceandalignwiththeburnerports(seephotobelow).



DVS GSR Dancing-Fyre Burner
Installation Instructions (SKU96900103)


Page 3 of 4 17601694.docx — 9/25/18 © Travis Industries, Inc.

DRIFTWOODORFYRE‐STONESONLY:
Disablethelightbyremovingthebulbandlayingthehousingflatinthefireboxcavity.Replacethescrew
fromthelightbracketintothefireboxfloor.


DRIFTWOODORFYRE‐STONESAIRDEFLECTORINSTALLATION:
Attachtheairdeflectortotherearofthefireboxcavity,usingthescrewsalreadyinplace.
 
 



DVS GSR Dancing-Fyre Burner
Installation Instructions (SKU96900103)


Page 4 of 4 17601694.docx — 9/25/18 © Travis Industries, Inc.

TRADITIONALLOGSETAIRDEFELCTORINSTALLATION:
a) Usetinsnipstocutoutthenotchintheairdeflectortoallowittofitaroundthelightbracket.
b) Attachtheairdeflectortotherearofthefireboxcavity,usingthescrewsalreadyinplace.Insert
theairdeflectorwiththescrewholesfacingup,sothenotchfitsaroundthelightbracket,and
thentiltitbacksothescrewholesarealignedwiththeholesprovidedinthefirebox.



