Travis Industries Tempest Portable Torch User manual

Tempest Torch
Owner’s Manual
• Gas Fired Torch
• Natural Gas (sku 94900743)
• Propane (sku 94900753)
WARNING: For Outdoor Use Only
Tested and Listed by
OMNI-Test Laboratories, Inc.
Portland, Oregon
Report # 028-F-83-5
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Read this manual thoroughly before installing or servicing this
equipment. For assistance or additional information consult a qualified installer,
service agency, or the gas supplier.
Installer: After installation give this manual to the homeowner and
explain operation of this appliance.
$10.00 ©Copyright 2008, T.I. Part # 100-01203_000

2Introduction
© Travis Industries, Inc. 4050608 100-01203_000
Overview
This manual details the installation, operation, and routine maintenance for the Tempest
torch.
Listing Details
This torch was tested to: Applicable portions of ANSI Z21.42a-2004 “Illuminating
Appliances”, CAN 1-2.15, CSA 4.96 U.S. (3rd Ed) “Outdoor Gas Fireplace”, and AGA 8-
96, “Requirement for Gas-Fired Decorative Illuminating Appliances for Outdoor
Installation.” A copy of the safety label is shown below.
Important Registration and Service Information
No other Tempest torch has the same serial number as yours. The serial number is on the
safety label attached by a chain near the control panel. This serial number will be needed in
case you require service of any type. To receive full warranty coverage, you will need to show
evidence of the date of purchase. Mail your warranty card or visit traviswarranty.com to register
your Tempest torch. If any service issues may arise, contact your dealer for details.

Table of Contents 3
© Travis Industries, Inc. 4050608 100-01203_000
Introduction
Overview.............................................................2
Listing Details......................................................2
Important Registration and Service Information..2
Safety Precautions
Safety Precautions..............................................4
Features & Specifications
Features..............................................................5
Installation Options .............................................5
Specifications......................................................5
Dimensions.........................................................5
Installation
Installation Warnings...........................................6
Packing List......................................................... 6
Additional Items Required for Installation............ 6
Recommended Order of Installation ...................6
Placement Requirements.................................... 7
Gas Line Requirements ...................................... 8
Gas Line Connection ..........................................8
Post Mount and Control Cover Installation.......... 9
Torch Assembly..................................................10
Optional Rain Cap...............................................11
Wall Mount Kit.....................................................12
Post or Pier Mounted Torch................................ 13
Operation
Before You Begin................................................14
Operating Instructions......................................... 14
Maintenance
Maintaining Your Torch.......................................16
Winterizing The Torch.........................................16
Replacement Parts .............................................17
Troubleshooting Table ........................................ 18
Warranty
Warranty .............................................................19
Index
Index...................................................................20

4Safety Precautions
© Travis Industries, Inc. 4050608 100-01203_000
! This appliance must be installed in accordance with all local codes, if any; if not, follow
ANSI Z223.1.
! This appliance must only be used outdoors in a well-ventilated area. It may not be used
in a building, garage, or other enclosed space.
• This appliance is not for use with solid fuel.
• The torch must be kept clean and free of leaves and debris to insure safe operation.
• Any hose or gas-supply line that is damaged or shows evidence of excessive abrasion or wear must be
replaced prior to use of the torch.
• If using a gas supply line to the torch, make sure it is properly located away from any walkway or in an
area where it may be subject to accidental damage
• Educate all children and adults of the dangers of the torch. Young children should be supervised when
they are in the same area as the torch. Do not let children play with the torch.
• Do not place clothing or other flammable items on or near the torch.
• Any screen or guard removed for servicing must be replaced prior to operating the torch.
• This unit must be installed and repaired by a qualified installer to prevent the possibility of an explosion.
Your dealer will know the requirements in your area and can inform you of those people considered
qualified. The torch should be inspected before use and at least annually by a qualified service person.
More frequent cleaning may be required due to excessive debris from leaves, dirt, insects, etc.
• Do not operate if any portion of the controls were submerged in water or if any corrosion occurs.
• The instructions in this manual must be strictly adhered to. Do not use makeshift methods or compromise
in the installation. Improper installation will void the warranty and safety listing.
• This appliance is either approved for natural gas (NG) or for propane (LP). Burning the incorrect fuel will
void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about the
type of fuel used to your dealer. A label is placed on the control panel to show which fuel the torch is
designed for (in addition, NG units have 25 burner holes, LP units have 49 burner holes).
• Contact your local building officials to obtain a permit and information on any installation restrictions or
inspection requirements in your area.
• If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the torch. Call your
dealer and arrange for proper servicing.
• Do not operate the torch if it is not operating properly in any fashion or if you are uncertain. Call your
dealer for a full explanation of your torch and what to expect.
• Do not store or use gasoline or other flammable liquids in the vicinity of this torch.
• Never remove, replace, modify or substitute any part of the torch unless instructions are given in this
manual for routine maintenance and cleaning. A trained technician must do all other work. Do not modify
or replace orifices.
• Allow the torch to cool before carrying out any maintenance or cleaning.
• Operate the torch according to the instructions included in this manual.
• If the burner does not start correctly turn the gas off at the gas control valve and call your dealer for
service.
• Do not use this appliance to cook food.
• Instruct everyone in the house how to shut gas off to the torch and at the gas main shutoff valve. The gas
main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to shut off.
• Do not operate the torch during a lightning storm or a possible lightning storm.
• Do not operate the torch during high wind conditions.
• Do not install in or on recreational vehicles and/or boats.
• Do not throw this manual away. This manual has important operating and maintenance instructions that
you will need at a later time. Always follow the instructions in this manual.
• Travis Industries, Inc. grants no warranty, implied or stated, for the installation or maintenance of
your torch, and assumes no responsibility of any consequential damage(s).

Features and Specifications 5
© Travis Industries, Inc. 4050608 100-01203_000
Features:
- Maximum 20,000 BTU Input
- Removable Rain Cap
- Tempered Glass (easy to remove and clean)
- Stainless Steel Construction
- Automatic Gas Shutoff Valve for Safety
- Rotary Piezo Igniter for Easy Lighting
- Wet Weather Lighting Port for Positive Ignition
Installation Options:
- For Outdoor Installation Only
- For Fixed Line Installations Only
- Wall Mount
- Post Mount
- Pier Mount
Specifications:
NG LP
Input Rating (Btuh) High - Low 20,000 – 14,000 20,000 – 17,500
Orifice Size (DMS) #50 #55
Burner Ports 25 Holes 49 Holes
Manifold Pressure 7" wc 11" wc
Max. Inlet Pressure 7" wc 11" wc
Dimensions:
NOTE: All Clearances are measured from the glass (and glass frame).
8-7/8”
2-1/2”
19-1/2”
9-1/2”
8-7/8”
9-1/2”

6Installation (for qualified installers only)
© Travis Industries, Inc. 4050608 100-01203_000
Installation Warnings:
! This appliance is designed for outdoor use only, in well-ventilated areas.
! Failure to follow all of the requirements may result in property damage, bodily
injury, or even death.
! This torch must be installed by a qualified installer.
! This appliance is designed to operate on natural gas, or propane (LP).
! Notify your insurance company before hooking up this appliance. All relevant
information on the Tempest Torch is located on page 2, Important Information.
You can fax them page 2.
! The requirements listed below are divided into sections. All requirements must be
met simultaneously. The order of installation is not rigid – the qualified installer
should follow the procedure best suited for the installation.
Packing List
•Main Assembly
•Burner Top
•(4) Support Bars (w screws)
•Top Plate
•Rain Cap
•5/32” Hex Wrench
•Control Cover (pre-installed)
•(4) ¼-20 x ½” Hex Head Screws
Additional Items Required
This Torch Requires One of the Following Base Assemblies:
•Wall Mount Kit
•Post Mounting Kit
•Pier Mounting Kit
Recommended Order of Installation
1. Determine the location of the torch, making sure all clearances and requirements are met (see page 7).
2. Run the gas line and install through the post, pier, or wall mount (see the instructions included with these
kits).
3. Attach the torch assembly to the gas line and attach the torch assembly to the mount (see page 9).
4. Assemble the torch (see page 10 - attach the rain cap if desired – see page 11).
5. Bleed the gas line then start the torch (see page 14). Verify the torch works correctly and there are no gas
leaks.
6. Give this manual to the homeowner and explain operation of the torch.

Installation (for qualified installers only) 7
© Travis Industries, Inc. 4050608 100-01203_000
Placement Requirements
! For Outdoor Use Only. Install in well-ventilated areas.
Do Not Locate the Torch:
•In high traffic areas.
•Under or near trees, plants and buildings where debris may constantly fall into the torch.
Excessive debris will require high maintenance and/or cause malfunctioning of the torch.
•In places where people, children, and pets may contact the torch. Guards or fences
around the torch in these locations are recommended.
•In places where the controls beneath the torch may be submerged under water.
Submerging of any part of its controls will require complete replacement of the controls.
Clearances:
•The distance from ground level to the base of the burner shall be a minimum of 7 ft. (2.1M)
where installed within 2 feet (0.6M) of public walkways (e.g.: sidewalk, shared walkway
between two homes, or pathway in commercial applications). Lesser clearances shall be
permitted to be used only where acceptable to the authority having jurisdiction.
•Keep combustibles away from the shaded heat zone of the torch (see illustration below).

8Installation (for qualified installers only)
© Travis Industries, Inc. 4050608 100-01203_000
Gas Line Requirements
! The gas line must be installed in accordance with all local codes or, in the absence of local
codes, with the National Fuel Gas Code, ANSI Z223.1. Consult your local gas supplier or
propane gas dealer for code regulations and recommended procedures.
! The torch and gas control valve must be disconnected from the gas supply piping during any
pressure testing of that system at test pressures in excess of 1/2 psig. For pressures less
than 1/2 psig, isolate the gas supply piping by closing the manual shut-off valve.
! Leak test all gas line joints and the gas control valve prior to and after starting the torch.
LP and NG Configuration
This torch is shipped either for natural gas or for propane. The torch is not convertible from one fuel
to another. Check the sticker on the control panel to make sure the correct fuel is used. The torch has
unique orifices and burners for each fuel. See the table below for details.
NG LP
Input Rating (Btuh) 20,000 20,000
Orifice Size (DMS) #50 #55
Burner Ports 25 Holes 49 Holes
Manifold Pressure 7" wc 11" wc
Max. Inlet Pressure 7" wc 11" wc
Gas Line Connection
A manual shutoff valve is required on the gas supply to the torch. It should be placed upstream of the flex
line. A shut-off valve is included with the optional wall-mount kit.
NOTE: This version of the tempest torch may not be connected to a portable LP cylinder.

Installation (for qualified installers only) 9
© Travis Industries, Inc. 4050608 100-01203_000
Post Mount and Control Cover Installation
A post mount and control cover are pre-attached to the torch for use with the optional post (3” round lamp post)
or pier mount. If using the wall mount, use the control cover included with the wall mount kit.
(a) Detach the control cover
from the torch assembly.
Keep the two thumb screws
used to attach the cover.
(b) Slide the control cover over
the post.
HINT: Use low-tack tape to
protect the post from
scratches.
NOTE: When installing the
post, make sure the post is
positioned with the
mounting holes 45° offset
from the front. The post
mount has obround holes
that allow 20° of rotation
(10° in each direction).
(c) Attach the gas line.
WARNING: Take care
when handling the torch
assembly to not damage
the gas line.
(d) Attach the torch to the post
using the included ¼-20
screws.
(e) Attach the control cover to
the torch with the two thumb
screws.
! The safety label slides
into place between the
control cover and the
torch body.

10 Installation (for qualified installers only)
© Travis Industries, Inc. 4050608 100-01203_000
Torch Assembly
(a) Place the burner top over the
main assembly. Make sure the
burner top is fully seated.
! Make sure the wet weather
lighter openings line up.
(b) The support bars are shipped
with two screws pre-installed.
Remove the screws from the
support bars and attach the four
bars to the main assembly.
Make sure the bars are properly
aligned (square to the edge of
the main assembly).
(c) Attach the top plate.
NOTE: If using the optional rain
cap, you may wish to install it
now before the glass is installed
(see page 13).
(d) Slide one piece of glass into
place until it contacts the support
bar.
! Make sure the teflon tape is at
the top of the glass with the
wrap-around edge facing
inwards.
HINT: Make sure the glass is
clean before installing and
handle with soft gloves or other
non-marking material (e.g. paper
towel).
(e) Use a 5/32” hex wrench to
tighten the glass support bolt.
!Tighten the bolt only enough to
hold the glass in place – over-
tightening may break the
glass.
Repeat steps “d” and “e” for the
other three pieces of glass.

Installation (for qualified installers only) 11
© Travis Industries, Inc. 4050608 100-01203_000
Optional Rain Cap
The optional rain cap may be installed to suit the installation location. If the torch is located in an area where
rain or plant debris is prevalent, you may wish to permanently mount the rain cap to the torch with the
included nuts.
Place the rain cap on top of the torch so the four studs insert through the top plate. With one or two pieces of
glass removed, secure the rain cap using the included nuts (shipped pre-attached to the rain cap).

12 Installation (for qualified installers only)
© Travis Industries, Inc. 4050608 100-01203_000
Wall Mount Kit
An optional wall mount kit is available for mounting the tempest torch to a wall (or other horizontal structure).
See the the wall mount kit for full set of assembly and installation instructions.
NOTE: The control cover and post mount are not used when using the wall mount kit.

Installation (for qualified installers only) 13
© Travis Industries, Inc. 4050608 100-01203_000
Post or Pier Mounted Torch
The tempest torch may be mounted to a 3” diameter post using the included post mount. This post may be
surface mounted on a deck or similar platform with the optional post base kit. If the post is placed in a remote
location, it may be sunk into the ground using concrete or other suitable means. See the post or post base kit
for assembly and installation instructions.

14 Operation
© Travis Industries, Inc. 4050608 100-01203_000
Before You Begin
! Read this entire manual before you use your new torch, especially the section "Safety
Precautions" on page 4. Failure to follow the instructions may result in property
damage, bodily injury, or even death.
! Remove any cover from the torch prior to operation (the optional stainless-steel rain cap
may be left in place.
! Inspect the torch to make sure it is free of debris or objects that may have fallen into the
torch prior to operation.
! Inspect the torch, burner, and supply lines for any damage prior to operation.
! It may be difficult to see the burner operating in direct sunlight.
Operating Instructions
WARNING: Do not continue to push in the valve control in if the torch does not light. By
pushing the valve control in, you are allowing gas to flow to the torch,
creating an explosion hazard. If the torch does not light, push the valve
control in and rotate the valve to the OFF position.
Lighting the Torch – DRY WEATHER
1. Push valve control in and turn counter-clockwise to
START/HIGH position, then release.
2. Turn the DRY WEATHER IGNITER clockwise to create
spark (continue turning while performing step #3).
WARNING: Make sure the igniter is sparking before
continuing to step 3. The spark is best viewed
by adjusting your viewing angle so eye level is
level with the burner top (see the illustration to
the right). The spark typically jumps from the
spark electrode to the burner ring.
3. Push and hold valve control in. Torch must light within 5 seconds. After torch lights
continue to hold valve control in for 15 seconds. Note – if torch does not light use a
wand lighter in the wet weather lighter opening and perform step #3 to light.

Operation 15
© Travis Industries, Inc. 4050608 100-01203_000
Lighting the Torch – WET WEATHER
1. Push valve control in and turn
counter-clockwise to START/HIGH
position, then release.
2. Insert a wand lighter through the
WET WEATHER LIGHTER
OPENING.
3. With the wand lighter lit, push and
hold valve control in. Torch must
light within 5 seconds. Remove the
wand lighter. After torch lights
continue to hold valve control in for
15 seconds. Note – if torch does
not light with a wand lighter directly
next to the burner with the valve
control pressed in in the
START/HIGH position, gas is not
reaching the torch.
Turning the Torch Off
1. Push valve control in and turn clockwise to the OFF position. Note – if excessive
wind or rain extinguishes the flame the safety control automatically turns gas off.

16 Maintenance
© Travis Industries, Inc. 4050608 100-01203_000
Maintaining Your Torch
! Failure to inspect and maintain may lead to malfunctioning of the appliance
and potentially dangerous situations.
•Inspect Torch prior to each use.
•Keep torch clean, remove any debris that collects in or on Torch. Inspect for
spiders and insects, they may clog burner ports or air inlets and need be
removed before using.
•Have the appliance inspected by a qualified service technician annually.
•The stainless steel burner top will discolor – this is normal.
Your Tempest torch is designed to be cleaned and maintained easily. The most
common maintenance that your torch will require is glass cleaning. This is done by
loosening the glass retaining screws. Each piece of glass will have its own retainer.
Hold the glass by the exposed edge and slide horizontally out of its tracks, the glass
should slide easily if its retainer screw is loose.
Clean with glass cleaner or warm soapy water. The glass on your Tempest is tempered
and designed for safety. If it breaks it will shatter into small square pieces similar to a
car windshield. It is special glass and if you break one or need to replace a piece use
only 3/16” thick tempered glass supplied by your Tempest Torch dealer.
To inspect for or clean debris out of the inside of your torch remove one piece of glass.
This will provide access to the inside of your torch. Once your glass piece is out remove
the pyramid shaped piece with the rings on the top by lifting it straight up, once you are
clear of the burner elements turn it sideways and remove through the glass opening.
This will provide you a clear view of all the torch components, visually check for and
remove all foreign objects, vegetation, bugs, debris. When reassembling make sure you
orient the Pyramid plate correctly, the burner elements that stick up through this plate
are delicate. Once oriented, slide the plate straight down onto the burner assembly
making sure the edges are seated all the way down.
Winterizing The Torch.
These procedures only apply to areas where the torch will not be used during winter or for a long period of time.
1. Shut off gas supply to the torch.
2. Place the included rain cap over on top of the torch. If additional protection is desired, a cover may
be placed over the torch, making sure it does not damage the glass.

Maintenance 17
© Travis Industries, Inc. 4050608 100-01203_000
Replacement Parts
1 250-01256 RAIN CAP ASS'Y, TEMPEST
2 250-01257 VERTICLE ROD w/SCRWS, TEMPEST
3 250-01251 GLASS - TEMPEST
4 250-01250 FLAME SPREADER ASSY - NG
4 250-01261 FLAME SPREADER ASSY - LP
5 250-01269 SCW, SHCS, 10-24 x 2" STAINLES (4)
6 250-01252 KNOB, TEMPEST VALVE
7 250-01255 PIEZO KNOB, BLACK
8 250-01254 PIEZO IGNITER, w/ MNTG SCRWS
9 250-01268 MAGNET w/OUT SHEATH (w nut)
10 250-01253 VALVE, TEMPEST w/NUT
11 250-00666 FLEX PIPE, 3/8"od x8" BLK,
12 250-00409 ORIFICE, BURNER - No. 55
12 250-00753 ORIFICE, BURNER - No. 50
13 93006523 PILOT ELECTRODE, S.I.T. PILOT#
14 93006518 THERMO-COUPLE - S.I.T. #
Replacement parts can be obtained from your Tempest torch retailer (see www.tempesttorch.com).

18 Maintenance
© Travis Industries, Inc. 4050608 100-01203_000
Troubleshooting Table
Problem: Possible Cause: Don't Call for Service
Until You:
Torch Does Not Light Check shut-off valve.
Gas is Off
Verify shutoff valve is turned ON.
Turn Gas On
Igniter Does Not Spark Igniter is wet
Use the wet-weather starting
instructions.
Flames are too short
(under 6") The gas supply pressure to the appliance is too
low. Depleted LP cylinder.
Gas supply lines or gas regulators do
not have enough capacity. This
maybe due to other appliances in the
house using up the available capacity,
e.g. pool heaters, furnaces, hot water
tanks, etc.
Flames are not Spiral Torch was just turned on
Windy Condition
It takes 5 to 10 minutes for the torch to
start up and the flame to form a spiral.
Wind will influence the flame shape
Glass is Sooting Burner or burner orifice may be dirty or blocked
Windy Condition
Contact your dealer for details on
removing any debris (spider webs,
etc.) from the burner and orifice area.
Wind will influence the flame quality
and, if persistent, may lead to sooting
on the glass.
Torch makes Clicking
Sounds Glass is moving inside the glass frame and the
stainless steel parts are expanding and
contracting with heat
THIS IS NORMAL
.

Warranty 19
© Travis Industries, Inc. 4050608 100-01203_000
To register your TRAVIS INDUSTRIES, INC. 1 Year Limited Warranty, complete the enclosed Warranty card and mail it within ten (10) days of the
appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants
this gas appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to
the original purchaser from the date of purchase as follows:
Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges
are not covered by this warranty. This charge can vary from store to store.
Year 1 COVERAGE: PARTS & LABOR
Burner Assembly:
Burner, Venturi, Flame Spreader, Orifice, Gas Control Assembly: Gas valve, cover plate and hardware, thermocouple, pilot hood, pilot gas line,
piezo igniter, tip switch and wiring, LP regulator (if applicable)
Glass:
Glass (breakage from thermal shock only)
Accessories:
Portable base (including post and tank cover), wall mount bracket, in-ground post, and pier post
One-Way Freight Allowance:
One-way freight allowance on pre-authorized repair done at factory is covered.
Exclusions: Paint and Finish
CONDITIONS & EXCLUSIONS
1. This new gas appliance must be installed by a qualified gas appliance technician. It must be installed, operated, and maintained at all times in accordance with the
instructions in the Owner’s Manual. Any alteration, willful abuse, accident, neglect, alteration, misapplication or misuse of the product shall nullify this warranty.
2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized TRAVIS dealer.
3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered under
warranty. The installer must ensure the appliance is burning as per the rating tag at the time of installation. Over-firing (operation above the listed BTU rate) of this
appliance can cause serious damage and will nullify this warranty.
4. This warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.
5. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings, roof tops, wind, hills or
mountains or other influences from mechanical systems such as fans, etc.
6. This Warranty is void if:
a. The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.
b. The unit is subject to submersion in water.
7. Exclusions to this 1 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or
adjustment of the manufacturer's settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in transit, alteration, or act of
God.
8. This 1 Year warranty excludes damage caused by normal wear and tear, such as discoloration. Also excluded is damage to the unit caused by abuse, improper
installation, modification of the unit, drilling of the orifices, or the use of fuel other than that for which the unit is configured. Units are shipped for either natural gas or
propane. Confirm fuel configuration with your installer.
9. Damage to stainless steel surfaces caused by fingerprints, scratches, melted items , or other external sources left on the stainless steel from the use of cleaners is not
covered in this warranty.
10. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or consequential
damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage may not apply.
11. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the gas appliance without the express
written permission of TRAVIS INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.
12. Any statement or representation of TRAVIS products and their performance contained in TRAVIS advertising, packaging literature, or printed material is not part of this
1 year warranty.
13. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way.
14. No dealer, distributor, or similar person has the authority to represent or warrant TRAVIS products beyond the terms contained within this warranty. TRAVIS
INDUSTRIES, INC. assumes no liability for such warranties or representations.
15. Travis Industries will not cover the cost of the removal or re-installation.
16. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.
17. THIS 1 YEAR WARRANTY IS THE ONLY WARRANTY SUPPLIED BY TRAVIS INDUSTRIES, INC., THE MANUFACTURER OF THE APPLIANCE. ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, ARE HEREBY EXPRESSLY DISCLAIMED AND PURCHASER’S RECOURSE IS EXPRESSLY LIMITED TO THE
WARRANTIES SET FORTH HEREIN.
IF WARRANTY SERVICE IS NEEDED:
1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your TRAVIS dealer WITHIN 30 DAYS, giving them proof of purchase,
the purchase date, and the model name and serial number.
2. Travis Industries has the option of either repairing or replacing the defective component.
3. If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership
where you purchased the appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may
be asked to ship your appliance, freight charges prepaid, to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge,
your TRAVIS appliance if it is found to be defective in material or workmanship within the time frame stated within this 1 year warranty. TRAVIS INDUSTRIES, INC. will
return your appliance, freight charges prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or dealership.

20 Index
© Travis Industries, Inc. 4050608 100-01203_000
Additional Items Required for Installation............................................ 6
Before You Begin................................................................................ 14
Dimensions......................................................................................... 5
Features.............................................................................................. 5
Gas Line Connection .......................................................................... 8
Gas Line Requirements ...................................................................... 8
Important Registration and Service Information.................................. 2
Installation Options ............................................................................. 5
Installation Warnings........................................................................... 6
Listing Details...................................................................................... 2
Maintaining Your Torch....................................................................... 16
Operating Instructions......................................................................... 14
Optional Rain Cap............................................................................... 10
Packing List......................................................................................... 6
Placement Requirements.................................................................... 7
Post Mount and Control Cover Installation.......................................... 11
Post or Pier Mounted Torch................................................................ 13
Replacement Parts ............................................................................. 17
Safety Precautions.............................................................................. 4
Specifications...................................................................................... 5
Torch Assembly.................................................................................. 9
Troubleshooting Table ........................................................................ 18
Wall Mount Kit..................................................................................... 12
Warranty ............................................................................................. 19
Winterizing The Torch......................................................................... 16