Travis Industries LOPI Liberty User manual

L i b e r t y
Wood Stove
Owner's Manual
• Freestanding Stove
• Mobile-Home Approved
• Alcove Approved
• Hearth-Stove Approved
Save these instructions
for future reference
SAF TY NOTIC :
If this appliance is not properly installed, a house fire may
result. For your safety, follow the installation directions.
Contact local building or fire officials about restrictions and
installation inspection requirements in your area.
 Copyright 2007, T.I.
10.00 100-01164
4050922 Listed
Tested to: U.L. 1482

2 Introduction
© Travis Industries 100-01164 4041115
Introduction
We welcome you as a new owner of a Lopi Liberty wood-burning stove. In purchasing a Lopi Liberty you
have joined the growing ranks of concerned individuals whose selection of an energy system reflects both
a concern for the environment and aesthetics. The Lopi Liberty is one of the finest appliances the world
over. This manual will explain the installation, operation, and maintenance of this appliance. Please
familiarize yourself with the Owner's Manual before operating your appliance and save the manual for
future reference. Included are helpful hints and suggestions which will make the installation and
operation of your new appliance an easier and more enjoyable experience. We offer our continual
support and guidance to help you achieve the maximum benefit and enjoyment from your appliance.
Important Information
No other Lopi Liberty appliance has the same serial
number as yours. The serial number is stamped onto
the label on the back of the appliance.
This serial number will be needed in case you require
service of any type.
Model: Lopi Liberty
Serial Number:
Purchase Date:
Purchased From:
Mail your Warranty Card Today, and Save Your Bill
of Sale.
To receive full warranty coverage, you will need to
show evidence of the date you purchased your
appliance. Do not mail your Bill of Sale to us.
We suggest that you attach your Bill of Sale to this
page so that you will have all the information you need
in one place should the need for service or information
occur.

Table of Contents 3
© Travis Industries 100-01164 4041115
General Information
Introduction & Important Information...................... 2
Safety Precautions ............................................ 4
eatures & Specifications.................................... 6
Stove Installation
Planning The Installation..................................... 7
loor Protection Requirements ............................. 8
Stove Placement Requirements ........................... 8
Clearances ...................................................... 8
Chimney Requirements ...................................... 10
Chimney Termination Requirements...................... 11
Outside Air Requirements ................................... 11
Alcove Installation Requirements .......................... 12
Mobile Home Requirements ................................ 13
INSTALLATION DIAGRAMS
Standard Ceiling with a actory Built Chimney......... 14
Cathedral Ceiling with a actory Built Chimney........ 14
Exterior actory Built Chimney ............................. 15
Hearth Stove Positive Connection......................... 15
Hearth Stove Direct Connection ........................... 16
Interior Masonry Chimney ................................... 16
Operating Your Applian e
Safety Notice.................................................... 17
Before Your irst ire......................................... 17
Opening the Door .............................................. 17
Bypass Operation.............................................. 18
Starting a ire................................................... 19
Adjusting the Burn Rate ...................................... 20
Ash Removal.................................................... 20
Optional Blower Operation .................................. 21
Re-Loading the Stove......................................... 21
Overnight Burn ................................................. 21
Normal Operating Sounds ................................... 21
Hints for Burning ............................................... 22
Selecting Wood................................................. 22
Troubleshooting ................................................ 23
Maintaining Your Applian e
Daily Maintenance ............................................. 24
Remove Ash .................................................... 24
Clean The Glass ............................................... 24
Monthly Maintenance ......................................... 25
Door and Glass Inspection .................................. 26
Check or Creosote Buildup ................................ 25
Yearly Maintenance ........................................... 26
Touch Up Paint ................................................. 26
Blower Cleaning................................................ 26
irebrick and Baffle Inspection ............................. 26
Door Parts ....................................................... 27
Replacing the Glass........................................... 27
Replacing the Door Gasket.................................. 27
Replacing the Door Handle.................................. 27
irebox Parts.................................................... 28
loor & Side irebrick Removal & Replacement....... 28
Baffle Removal and Replacement ......................... 29
Air Tube Removal and Replacement ..................... 29
Warranty
Warranty ......................................................... To
Listing Information
Listing Information ............................................. 31
Optional Equipment
Door Shell Installation ........................................ 32
Stove Legs....................................................... 34
Pedestal .......................................................... 35
Rear Blower Installation ...................................... 36
Outside Air Boot Installation................................. 37
Index
Index .............................................................. 38

4 Safety Precautions
© Travis Industries 100-01164 4041115
The viewing door must be
closed and latched during
operation.
Never bloc free airflow through
the air vents on this appliance.
Gas
Gasoline or other flammable
liquids must never be used to
start the fire or "Freshen Up" the
fire. Do not store or use
gasoline or other flammable
liquids in the vicinity of this
appliance.
This appliance is designed and
approved for the burning of cord
wood only. Do not attempt to
burn any other type of fuel other
than cord wood in this
appliance, it will void all
warranties and safety listings.
ASHES
Ashes must be disposed in a
metal container with a tight lid
and placed on a non-
combustible surface well away
from the home or structure.
Do not touch the appliance while
it is hot and educate all children
of the danger of a high-
temperature appliance. Young
children should be supervised
when they are in the same room
as the appliance.
36"
Keep furniture, drapes, curtains,
wood, paper, and other
combustibles a minimum of 36"
away from the front of the
appliance.
This appliance must be properly
installed to prevent the
possibility of a house fire. The
instructions must be strictly
adhered to. Do not use
ma eshift methods or
compromise in the installation.
Ok
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this appliance as well.
Inspect the chimney connector
and chimney at least twice
monthly and clean if necessary.
Creosote may build up and
cause a house fire.
Do not connect this appliance to
any chimney serving another
appliance.
Type
HT Clay
Liner
This appliance must be
connected to a listed high
temperature (UL 103 HT)
residential type chimney or an
approved masonry chimney with
a standard clay tile, or stainless
steel liner.

Safety Precautions 5
© Travis Industries 100-01164 4041115
Mobile
Home
When installed in a mobile
home, this appliance must be
bolted to the floor, have outside
air, and not be installed in the
bedroom (Per H.U.D.
requirements). Chec with local
building officials.
Do not place clothing or other
flammable items on or near this
appliance.
Never try to repair or replace
any part of this appliance unless
instructions are given in this
manual. All other wor must be
done by a trained technician.
Do not ma e any changes or
modifications to an existing
masonry fireplace or chimney to
install this appliance.
Do not ma e any changes to the
appliance to increase
combustion air.
A
A
A
A
Allow the appliance to cool
before carrying out any
maintenance or cleaning. Overfiring the appliance may
cause a house fire. If a unit or
chimney connector glows, you
are overfiring.
Maintain the door and glass seal
and eep them in good
condition.
Avoid placing wood against the
glass when loading. Do not
slam the door or stri e the glass.
Do not use a grate or other
device to elevate the fire off of
the firebox floor. Burn the fire
directly on the bric s.
This
Manual
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Travis Industries, Inc. grants
no warranty, implied or
stated, for the installation or
maintenance of your
appliance, and assumes no
responsibility of any
consequential damage s).

6 Features & Specifications
© Travis Industries 100-01164 4041115
Installation Options
• Freestanding
• Freestanding in an Alcove
• Freestanding in a Mobile Home
• Freestanding Hearth Stove
Features
• EPA Phase II Approved
• 3.1 Cubic Foot Firebox Volume
• Single Operating Control
• Accepts Logs Up to 24" Long
• Steel Plate Construction (5/16" & 3/16")
• Heavy Duty Refractory Firebric
• Optional High-Tech Blower
Heating Specifications
Approximate Maximum Heating Capacity (in square feet)* 1,500 to 2,500
Maximum BTU's per Hour (Cord Wood Calculation) 74,300
Overall Efficiency (Oregon Method) 70 %
Maximum Burn Time Up to 12 Hours
* Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature.
It is also affected by the quality and moisture level of the fuel.
Dimensions
30”
21”
Note:
Measure side, corner, and back
clearances from the stove top.
Measure front clearances from
the stove face.
Height:
Sculptured or Cast Legs....32-1/4"
Pedestal.............................36-1/4"
The 6”diameter flue collar protrudes
1-1/4" above the stove top
6-1/4”
Weight: 470 Lbs.
Figure 1
Emissions
2.6 Grams Per Hour (EPA Phase II Approved) – Tests conducted by E.E.S.P.C.

Stove Installation for qualified installers only) 7
© Travis Industries 100-01164 4041115
SAFETY NOTICE:
Please read this entire manual before you install and use your new room heater. Failure
to follow instructions may result in property damage, bodily injury, or even death.
Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Planning The Installation
We suggest that you have an authorized Travis Industries dealer install your stove. If you install the
stove yourself, your authorized dealer should review your installation plans.
Chec with local building officials for any permits required for installation of this stove and notify your
insurance company before proceeding with installation.
Preparation for Installation
• Chec for damage to the exterior of the stove (dents should be reported, scratches can be fixed by
applying touch up paint).
• Chec the interior of the firebox (replace crac ed firebric and ma e sure baffle is in place).
The stove can be lightened by removing the firebric s and baffle (pg 28) - replace before operation.
Additional Accessories Needed for Installation
• Door Shell (Blac 99300165 Brass 99300166 - see pg 32)
• Legs or Pedestal
Stove Installation Considerations
The table below details the six most common types of installations and the considerations for each type.
Alternative methods of installation are available if they comply with local building codes.
Installation Type Considerations
Standard Ceiling with a Factory Built Chimney
(Page 14) • Requires ceiling and roof penetration
• Provides best draft
Cathedral Ceiling with a Factory Built Chimney
(Page 14) • Cathedral style chimney support required
• Provides best draft
Exterior Factory Built Chimney
(Page 15) • Uses two elbows to route chimney outside
• Exterior chimney is hidden from the room
• Elbows reduce draft
• Optional exterior chase reduces cold air bloc age
Hearth Stove Positive Connection
(Page 15) • Utilizes existing masonry or zero clearance (metal) chimney
• Provides good draft due to full reline
• Easier to clean than direct or horizontal hearth stove
Hearth Stove Direct Connection
(Page 16) • Utilizes existing masonry or zero clearance (metal) chimney
• Requires construction of a "bloc -off plate"
• Draft reduced due to elbows & chimney cross section
Interior Masonry Chimney
(Page 16) • Utilizes existing masonry chimney (not approved for zero
clearance (metal) fireplaces)

8 Stove Installation (for qualified installers only)
© Travis Industries 100-01164 4041115
Floor Protection Requirements
• Stove must be placed on the Travis Industries legs or Pedestal.
• loor protection must extend 6" to the sides and rear of the stove and 16" to the front of the stove
(42" wide by 43" deep - see igure 2 and igure 3).
• loor protection must be non-combustible and at least .018" thick (26 guage).
Stove Placement Requirements
Clearances may be reduced by methods specified in N PA 211, listed wall shields, pipe shields, or
other means approved by local building or fire officials.
• Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36"
of the front of the stove
• If the stove is placed in a location where the ceiling height is less than 7', it must follow the
requirements in the section "Alcove Installation Requirements"
• Must maintain the clearances to combustibles listed below (drywall, furniture, etc.):
Clearances
• The following clearances must be met (see igure 2 and igure 3)
Minimum Clearance Singlewall
Connector
Reduced
Clearance*
A Sidewall to stove 16" 16"
B Backwall to stove 15” 10"
C Cornerwall to stove 9-1/2" 7-1/2"
D Connector to sidewall 28" 27-1/2"
E Connector to backwall 18-1/4" 12-3/4"
Connector to cornerwall 21" 18-1/2"
*Reduced clearance installations require one of the chimneys and connectors listed below:
AMERI-TEC model DCC with model HS chimney
DURAVENT model DVL with DURATEC or DURA-PLUS chimney
I.C.C. Excel (2100-2 Can.) (103-HT USA) chimney with HP connector
METAL AB model DW connector with TG chimney
SECURITY model DP connector with SECURITY model ASHT or S2100 chimney
Standard Masonry Chimney with any one of the above listed connectors
NOTE: Reduced clearance connectors may not connect to the flue collar – an appliance adapter may be required.
NO E: Standard residential installations with reduced clearance connector may use the clearance
determined by the manufacturer of the connector for the connector to wall clearance or the clearance
listed in this manual. Offsets must be used to maintain the stove to wall clearance.

Stove Installation (for qualified installers only) 9
© Travis Industries 100-01164 4041115
Top View -
Straight Installation
Measure rear and side
clearances from the nearest
edge of the stove top.
Measure front clearances
from the face of the stove
(uni ody).
NOTE: vent diameter may
vary depending on rand
and model.
AAAAAAAAAAAAA
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
A
AAAAAAAAAAA
A
AAAAAAAAAAAAA
Floor Protection
21”
16” Min.
6” Min.
6” Min.
Clearance A
Clearance D
Clearance E
Clearance B
Back Wall
Side Wall
6-1/4”
30”
Figure 2
Top View -
Corner Installation
AAAAAAAAAAAAAAA
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
A
AAAAAAAAAAAAA
A
AAAAAAAAAAAAAAA
Floor Protection
21”
16” Min.
6” Min.
6” Min.
6-1/4”
30”
Measure rear and side
clearances from the nearest
edge of the stove top.
Measure front clearances
from the face of the stove
(uni ody).
NOTE: vent diameter may
vary depending on rand
and model.
Corner Wall
Corner Wall
Clearance C
Clearance F
Figure

10 Stove Installation for qualified installers only)
© Travis Industries 100-01164 4041115
Chimney Requirements
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
• Chimney connector must be a minimum 24 MSG blac or 26 MSG blued steel (6" diameter). Chimney
must be used from the first floor or wall penetration to the chimney cap.
• Use 6" diameter type UL 103 HT chimney from one manufacturer (do not mix brands) or code
approved masonry chimney with a flue liner.
• Chimney connector and chimney must be fastened to the stove and each adjoining section.
• Follow the chimney manufacturer's clearances and requirements.
• Use the chimney manufacturer's fire stops, attic guards, roof supports, and flashings when passing
through a ceiling or thimble when passing through a combustible wall.
• No more than 180o of elbows (two 90o elbows, or two 45o & one 90o elbow, etc.).
• NOTE: Additional elbows may be allowed if draft is sufficient. Whenever elbows are used the draft is
adversely affected. Additional chimney height may be required to boost draft.
A
A
A
AA
AA
AA
AA
AA
AA
A
A
A
A
A
A
Chimney Cap
(See the section "Chimney Termination
Requirements" for more details)
A
AA
AA
AA
AA
AA
AA
AA
Factory Built Chimney Sections
Minimum Air Space to Combustibles
(See Chimney Manufacturer's
Instructions - usually 2")
Floor Penetration Equipment
(Attic Radiation Shield with Chimney Support)
Reduced Clearance Chimney
Connector Sections
Roof Penetration Equipment (Roof
Radiation Shield, Flashing, Storm Collar)
}
}
A
A
A
A
Stove Clearance
(as outlined in this manual)
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
A
A
A
A
}
Standard residential installations with reduced
clearance connector may use the clearance determined by
the manufacturer of the connector for the connector to wall
clearance or the clearance listed in this manual.
Mobile home installations must use the the reduced
clearance connector clearances listed in this manual under
“Additional Requirements for Mobile Home Installations”.
Minimum System 15'
Maximum System 33'
A
A
AAAAA
Floor
Protection
Figure 4
Drafting
Performance
This appliance relies upon natural draft to operate. External forces, such as wind,
barometric pressure, topography, or factors of the home (negative pressure from exhaust
fans, chimneys, air infiltration, etc.), may adversely affect draft. Travis Industries can not be
responsible for external forces leading to less than optimal performance.
Standard residential installations may use single-wall connector (Mobile-Homes may not)
• Standard residential installations with reduced clearance connector may use the clearance
determined by the manufacturer of the connector for the connector to wall clearance or the clearance
listed in this manual. Offsets must be used to maintain the stove to wall clearance. Mobile homes
must use the clearances listed in this manual under "Additional Requirements for Mobile Home
Installations".

Stove Installation for qualified installers only) 11
© Travis Industries 100-01164 4041115
Chimney Termination Requirements
• Must have an approved cap (to prevent water from entering)
• Must not be located where it will become plugged by snow or other material
• Must terminate at least 3' above the roof and at least 2' above any portion of the roof within 10' (see
Figure 5)
Slanted Roofs
F
lat Roofs
AA
A
A
A
Chimney must
extend 3'
above the roof
AAAAAAAAAAAAAAA
Chimney must extend 2'
above any portion of the roof
within 10' of the chimney
AA
AA
A
AA
AA
Chimney must
extend 3'
above the roof
Chimney must extend 2'
above any portion of the roof
within 10' of the chimney
Figure 5
Outsi e Air Requirements
• Required for mobile homes & in certain localities (chec with building officials)
• Must not be drawn from an enclosed space (garage, unventilated crawl space)
• Requires the optional outside air boot (for legs) or pedestal.
A
A
A
A
A
A
A
A
AAAAA
AAAAA
Optional Air Duct (must not be
longer than 15' and at least 16
square inches in cross section)
A hole must be cut
through the floor
protection and floor
and the rodent
screen nailed in
place here (see the
optional equipment
instructions for
exact sizes)
Outside
Air Boot
Outside air entrance must be placed so
it does not become blocked by snow.
When using outside air, find a location where the chimney and
outside air hole do not interfere with structural members of the home.
A
A
A
A
AAAAA
AAAAA
A
Pedestal (with insulation)
directs air to the stove.
A
A
A
A
Air may be drawn from a ventilated
crawl space or use an air duct.
Figure 6

12 Stove Installation (for qualified installers only)
© Travis Industries 100-01164 4041115
Alcove Installation Requirements
Whenever the stove is placed in a location where the ceiling height is less than 7' tall, it is considered an
alcove installation Because of the reduced height, the special installation requirements listed below must
be met
• Chimney connector and chimney must be one of the following types:
AMERI-TEC model DCC with model HS chimney
DURAVENT model DVL with DURATEC or DURA-PLUS chimney
I C C Excel (2100-2 Can ) (103-HT USA) chimney with HP connector
METALFAB model DW connector with TG chimney
SECURITY model DP connector with SECURITY model ASHT or S2100 chimney
Standard Masonry Chimney with any one of the above listed connectors
NOTE: Reduced clearance connectors may not connect to the flue collar – an appliance adapter may be required
• Alcoves are classified as combustible or non-combustible Non-combustible alcoves must have walls
and a ceiling that are 3 1/2" thick of a non-combustible material (brick, stone, or concrete - see Figure
7) This non-combustible material must be spaced and ventilated at least 1" off of all combustible
materials (walls, ceiling, etc ) to allow air to move around the non-combustible walls and ceiling All
other alcoves are considered combustible The clearances below must be met:
Minimum Clearance
(See the Figure 7 below)
Combustible
Alcove
Non Combustible
Alcove
A Sidewall to stove 16" 6"
B Backwall to stove 10" 2"
D Connector to sidewall 27-1/2" 17-1/2"
E Connector to backwall 12-3/4" 4-3/4"
G Maximum depth of alcove 48" 48"
H Minimum width of alcove 62" 42"
J Minimum height of alcove 84" 6" above stove top
Non-combustible alcove
construction (on walls
and ceiling) - see the
explanation above.
A
A
A
A
3 1/2" thick non-
combustible
material
Combustible
materials
1" Min.
Ventilated
air space
Non-combustible
reinforcer
a
b
de
h
j
g
Figure 7

Stove Installation (for qualified installers only) 13
© Travis Industries 100-01164 4041115
Mobile Home Requirements
• Outside air must be installed - see "Outside Air Requirements" on page 11
• Chimney connector and chimney must be one of the following types:
AMERI-TEC model DCC with model HS chimney
DURAVENT model DVL with DURATEC or DURA-PLUS chimney
I C C Excel (2100-2 Can ) (103-HT USA) chimney with HP connector
METALFAB model DW connector with TG chimney
SECURITY model DP connector with SECURITY model ASHT or S2100 chimney
Standard Masonry Chimney with any one of the above listed connectors
NOTE: Reduced clearance connectors may not connect to the flue collar – an appliance adapter may be required
• Stove placement must maintain the following clearances to combustibles (drywall, furniture, etc )
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
ab
f
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
c
Measure all clearances from the
nearest edge of the stove top.
d
ec
Rear heat
shield
Figure 8
Minimum Clearance
(See the illustration above)
Reduced Clearance
Connector
A Sidewall to stove 16"
B Backwall to stove 10"
C Cornerwall to stove 7-1/2"
D Connector to sidewall 27-1/2"
E Connector to backwall 12-3/4"
F Connector to cornerwall 18-1/2"
• If using offsets, use the connector clearance listed in Figure 9,
not the connector manufacturer's clearance
• The appliance must be secured to the floor (consult your
building official) Secure the outside air boot to the floor and
stove to insure the stove does not dislocate
• Mobile home installations require a spark arrester at the
chimney termination
• The appliance must be grounded to the chassis of the mobile
home (consult your building official)
• WARNING:DO NOT INSTALL IN SLEEPING ROOM.
• CAUTION:THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL, AND CEILING/ROOF MUST BE
MAINTAINED.
Minimum Stove
Clearance
(as outlined above)
AAAAA
12” Min.
Minimum Connector
Clearance
(as outlined above)
AA
AA
Figure 9

14 Stove Installation for qualified installers only)
© Travis Industries 100-01164 4041115
Standard Ceiling
with a Factory
Built Chimney
A
A
A
A
Chimney Cap
(See the section "Chimney
Termination Requirements"
for more details)
A
A
AA
AA
A
A
AA
AA
AA
AA
AA
AA
AAAAA
Chimney Sections
Minimum Air Space to
Combustibles (See
Chimney Manufacturer's
Instructions - usually 2")
Chimney Connector Sections
Follow the chimney
manufacturer's instructions
and clearances for roof
penetrations. A storm collar
and flashing are required
(some require a radiation
shield).
}
}
Minimum 15'
Maximum 33'
Stove Clearances
(See the section "Stove
Placement Requirements"
for more details)
Floor Protection
(See the section "Floor
Protection Requirements"
for more details)
Follow the chimney
manufacturer's instructions
and clearances for floor
penetrations. A ceiling
support is required, an attic
insulation shield is required
where insulation is present.
Insulation
Figure 10
Cathedral Ceiling
with a Factory
Built Chimney
A
A
A
A
Chimney Cap
(See the section "Chimney
Termination Requirements"
for more details)
A
A
AA
AA
A
A
AAAAA
AAAAA
Chimney Sections
Minimum Air Space to
Combustibles (See Chimney
Manufacturer's Instructions -
usually 2")
Follow the chimney
manufacturer's instructions
and clearances for roof
penetrations. A storm
collar, flashing, and
cathedral-style chimney
support are required
(some require a radiation
shield).
}
Minimum 15'
Maximum 33'
Stove Clearances
(See the section "Stove
Placement Requirements"
for more details)
Floor Protection
(See the section "Floor
Protection Requirements"
for more details)
Chimney
Connector
Sections
Figure 11

Stove Installation for qualified installers only) 15
© Travis Industries 100-01164 4041115
Exterior Factory
Built Chimney
NOTE:
Exterior chimneys are
subject to greater
moisture and creosote
accumulation due to the
lower temperatures. An
insulated chase will
reduce these
accumulations (the
proper clearances to the
chimney must be
maintained).
A
A
AA
AA
AA
AA
AA
AA
AA
C
himney Cap
(
See the section "Chimney
T
ermination Requirements"
f
or more details)
AA
AAAAA
Chimney Sections
M
inimum Air Space to
C
ombustibles (See
C
himney Manufacturer's
I
nstructions - usually 2")
Chimney Connector
Sections
A
A
AA
AA
A
Follow the chimney
manufacturer's
instructions and
clearances for roof
penetrations. A storm
collar and flashing are
required (some
require a radiation
shield).
}
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Stove Clearances
(See the section "Stove
Placement Requirements"
for more details)
}
Follow the chimney
manufacturer's
instructions and
clearances for wall
penetrations. A
wall radiation shield
(thimble) is
required.
Optional
insulated
chase
Wall Bands
and
Supports Insulated Tee
(with cleanout )
Minimum 15'
Maximum 33'
Min. 18"
clearance to
ceiling
Floor Protection
(See "Floor
Protection
Requirements"
for details)
Figure 12
Hearth Stove
Positive
Connection
NOTE:
Most factory-built
chimney manufacturers
ma e stainless steel
chimney liners, either
flexible or rigid. This
provides a wide variety
of installation options.
Ma e sure to follow the
manufacturer's
instructions for
installation and support.
A
A
AAA
AAA
AAA
AAA
AAA
AAA
AAA
A
A
A
A
A
A
A
Remove damper
or wire it open
Airtight Insulated
Clean-Out
Min. 18"
Combustible
Mantle
NOTE: The entire fireplace and
chimney must be clean, undamaged,
and meet all local building codes
(UBC, etc.). Damage must be
repaired prior to installation. The
chimney must be 15' to 33' tall.
Floor Protection
(See the section
"Floor Protection
Requirements"
for more details) See the section
"Stove Placement
Requirements" for
minimum clearances
required.
AA
The liner must be
stainless steel connector
or flexible vent. Follow
the liner manufacturer's
instructions for installation
and support.
Cap and flashing
prevents water from
entering
Figure 13

16 Stove Installation for qualified installers only)
© Travis Industries 100-01164 4041115
Hearth Stove Direct
Connection
NOTE:
Direct connections require
installation of an airtight,
non-combustible bloc -off
plate or damper adapter.
A
A
A
A
AAA
AAA
AAA
AAA
AAA
AAA
AAA
A
A
A
A
A
Block-off plate or
damper adapter
Remove damper
or wire it open
Airtight
Insulated
Clean-Out
Stainless steel
chimney connector
must Extend 1' past
the block-off plate or
to the flue liner
NOTE: The chimney must have a clay
tile liner. If it does not, the installation
must use a positive connection (full
reline). The entire fireplace and
chimney must be clean, undamaged,
and meet all local building codes (UBC,
etc.). Damage must be repaired prior
to installation. The chimney must be
15' to 33' tall.
Clay
Liner
Floor Protection
(See the section "Floor
Protection Requirements"
for more details)
Combustible Mantle
Min. 18"
See the section
"Stove Placement
Requirements" for
minimum clearances
required.
Max. 8”
Figure 14
Interior or Exterior
Masonry Chimney
NOTE:
This type of installation
requires a UBC approved
masonry connector or a
factory built (U.L. Listed)
wall thimble.
Make sure the
clean-out seals in
place.
Clay Liner
See the section "Stove
Placement Requirements" for
minimum clearances required.
Min. 18"
clearance
to ceiling
This type of
installation requires
a UBC approved
masonry connector
or a factory built
(U.L. Listed) wall
thimble.
Chimney connector sections
NOTE: The chimney must have a
clay tile liner. If it does not, the
installation must use a positive
connection (full reline). The
entire fireplace and chimney must
be clean, undamaged, and meet
all local building codes (UBC,
etc.). Damage must be repaired
prior to installation. The chimney
must be 15' to 33' tall.
See the section
"Floor Protection
Requirements"
A
A
A
A
Figure 15

Operating Your Appliance 17
© Travis Industries 100-01164 4041115
Safety Notice
If this appliance is not properly installed, a house fire may result. For your safety, follow the installation
directions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Read and follow all of the warnings on pages 4 and 5 of this manual.
Before Your First Fire
Verify the Installation
Before starting the stove, verify that the stove is properly installed and all of the requirements in this
manual have been followed.
Keep all flammable materials 36" away from the front of the stove (drapes, furniture, clothing, etc.).
Curing the Paint
This heater uses a heat-activated paint that will emit some fumes while starting
the first fire. Open doors and windows to the room to vent these fumes. This
typically lasts two to four hours. You may also notice oil burning off of the interior
of the heater. This rust-stopping agent will soon dissipate.
Door Gasket - The door gas et might adhere to the paint on the front of the
heater. Leave the door slightly ajar for the first fire and be careful when opening
the door after the first fire.
AAA
A
A
A
A
A
A
2 to 4 hours
Over-Firing the Stove
This stove was designed to operate at a high temperature. But due to differences in vent configuration,
fuel, and draft, this appliance can be operated at an excessive temperature. If the stove top or other area
starts to glow red, you are over-firing the stove. Shut the air control down to low and allow the stove to
cool before proceeding.
Over-firing may lead to damage of plated surfaces. If you are uncertain of over-firing conditions, we
suggest placing a stove thermometer (e.g. Rutland® Model 710) directly over the door on the stove top -
temperatures exceeding 800° are generally considered over-firing and will void the warranty.
Opening the Door
Rotate
the door
handle.
Swing
the door
open.
The door becomes hot during use. Use a glove to open the door if the handle is hot.
To prevent smo e from entering the room, open the bypass before opening the door (see following page
for directions). You can also open the door a small amount and let air enter the firebox.

18 Operating Your Appliance
© Travis Industries 100-01164 4041115
Bypass Operation
The bypass controls the flow of smo e inside the heater. When pulled out, smo e goes directly up the
flue, creating more draft. When pushed in, the smo e goes around the baffle, utilizing the secondary
combustion and ma ing the heater more efficient.
• When starting or re-loading, pull the bypass out.
• During normal operation, push the bypass in.
Bypass Pushed In
Used for normal operation
Bypass Pulled Out
Used for starting and re-loading
AA
AA
AA
AA
AA
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA
Use the included pull tool
to operate the bypass rod

Operating Your Appliance 19
© Travis Industries 100-01164 4041115
Starting a Fire
Since the dawn of time man has debated the best way to start a fire. Some use the boy-scout "tee-pee",
some prefer the "tic-tac-toe" stac . Either way, review the hints and warnings below to ensure proper fire
starting.
• Ma e sure the air control is pushed in and by-pass pulled out. If additional air is needed, open the
doors 1/4" during the first five minutes of start-up.
Never use gasoline, gasoline-type lantern fuel, erosene, charcoal lighter fluid, or similar liquids to start
or "freshen up" a fire in this stove. Keep all such liquids well away from the stove while it is in use.
If using a firestarter, use only products specifically designed for stoves - follow the manufacturer's
instructions carefully.
If the smo e does not pass up the chimney, ball up one sheet of newspaper, place it in the center of the
firebox and light it. This should start the chimney drafting (this eliminates "cold air bloc age").
Use plenty of indling to ensure the stove reaches a proper temperature. Once the indling is burning
rapidly, place a few larger pieces of wood onto the fire.

20 Operating Your Appliance
© Travis Industries 100-01164 4041115
A justing the Burn Rate
Use the air control slider to control the burn rate of the stove. See the illustration below for details.
Low Burn
(air control closed)
High Burn
(air control open)
A
A
A
A
AA
AA
AA
AA
AA
AA
AA
AA
Use the air control to
change the burn rate.
Approximate Air Control Settings
Overnight Burn Fully out to 9/32" open
Medium Burn 9/32" open to 5/16" open
Medium High Burn 5/16" open to 7/16" open
High Burn 7/16" open to pushed fully in
The air control becomes hot during operation - use gloves or a tool to prevent burns.
The air control may ta e several minutes to influence the burn rate. When ma ing adjustments, you
may wish to let the stove burn for 10 minutes to gauge performance.
Ash Removal
ASHES
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes
should be placed on a noncombustible floor or on the ground, away from all combustible
materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container until all cinders have thoroughly
cooled.