Traxxas 6590 User manual

Covers Parts #6590, 8485, 8486, 8487, 8488, 8489
LED Light Bar Kit Installation Instructions
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [email protected]
KC2619-R01 Rev 180718
Vehicle Body and Body Interior
Removal (Fig. 1):
1. Remove the 3x8mm flat-head screws
(12) from the vehicle body and
remove the body from the chassis.
2. Remove the 3x15mm button-head
screws (4) from both sides of the
center “X” roof support brace and
remove the brace.
3. Remove the 3x15mm button-head
screw, 3x20mm button-head screw,
and 3x30mm button-head screw
from the left side (driver side) of the
tube chassis to allow removal of the
body interior.
4. Remove the 3x8 flat-head screws from
the body interior (4) and remove the
interior from the chassis.
Body modification (Fig. 2 and 3):
If either the front grill LED light bar (#8486) or the rear LED
light bar (#8487) are being installed, the vehicle body will need
modification. Use Lexan® body scissors to cut out the section(s)
as indicated. Templates are provided at the bottom of page 3.
#6590 Kit Contents:
• High-Voltage Power Amplifier
• 3x12mm button-head screws (2)
#8485 Kit Contents:
• High-Voltage Power Amplifier
• Front grill LED light bars (2)
• Rear LED light bar
• Windshield LED light bar
• LED light bar mounts (2)
• 2-in-1 wire harness
• 3x10mm button-head screws (4)
• 3x12mm button-head screws (4)
• 3x15mm button-head screws (4)
• 3x20mm button-head screws (2)
• Zip ties (10)
#8486 Kit Contents:
• Front grill LED light bar
• LED light bar mounts (2)
• 3x10mm button-head screws (2)
• 3x15mm button-head screws (2)
• 3x20mm button-head screws (2)
• Zip ties (3)
#8487 Kit Contents:
• Rear LED light bar
• 3x12mm button-head screws (2)
• Zip ties (4)
#8488 Kit Contents:
• Windshield LED light bar
• 3x15mm button-head screws (2)
• Zip ties (2)
#8489 Kit Contents:
• 2-in-1 wire harness
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x8 FCS
3x30 BCS
3x15 BCS
3x20 BCS
3x15 BCS
3x15 BCS
3x15 BCS
3x15 BCS
Cut away material
✄
Cut away material
✄
Fig. 2 FRONT REAR
102mm x 28mm
102mm x 18mm
Fig. 1
Fig. 3

to ESC
Accessory
Port
3x15 BCS
3x12 BCS
3x12 BCS
3x12 BCS
3x15 BCS
3x20 BCS
3x10 BCS
3x10 BCS
3x15 BCS
3x20 BCS
3x15 BCS
D
B
A
E
CAUTION! To prevent damage to the electronic speed control (ESC) and/or the high-voltage power amplifier, ensure the batter(ies) are
disconnected before plugging the amplifier into the ESC.
High-Voltage Power Amplifier Installation:
1. Install the high-voltage power amplifier (A) on the left side of the vehicle chassis (two screw bosses on top of the battery
compartment). Ensure that the connectors on the amplifier face the front of the vehicle. Secure with the 3x12mm button-head
screws (2). Refer to the assembly diagram (Fig. 4) and wiring diagram (Fig. 7).
2. Remove the 3x25mm button-head screws (2) from the electronic speed control (ESC) to remove the cooling fan cover (Fig 5).
3. Remove the accessory port cover (Fig. 5); then, reinstall the cooling fan cover on the ESC using the 3x25mm button-head screws.
Be careful not to pinch the ESC wires during reinstallation.
4. Plug the 8-pin connector from the high-voltage power amplifier into the accessory port on the ESC (Fig. 6). The amplifier and
lights will turn on when the ESC is powered on.
LED Light Bar Installation:
1. Install the LED light kits; refer to the assembly diagram (Fig. 4) and wiring diagram (Fig. 8).
2. The front grill LED light bar mounts (B) install using the included hardware.
3. The front grill LED light bar(s) (C), windshield LED light bar (D), and rear LED light bar (E) install
as assemblies using the included hardware.
Note: A second front grill LED light bar can be installed and connected using the 2-in-1 wire
harness (part #8489). Two front grill LED light bars and the 2-in-1 harness are included with the
complete kit #8485.
4. Plug the LED light bar connectors into the high-voltage power amplifier ports (white
connector to A, yellow connector to B, red connector to C, blue connector to D) (Fig. 7).
5. Use the supplied zip ties to secure all wiring to the tube chassis.
Assembly Diagram
B
C
High-Voltage Power Amplier
Connection Ports
Front Grill LED Light Bar (white)
Windshield LED Light Bar (yellow)
Rear LED Light Bar (tail lights) (red)
Rear LED Light Bar (class lights) (blue)
ABCD
Fig. 4
Fig. 7
Fig. 6
B

Accessory Port Cover
3x25 BCS
3x25 BCS
Front Grill LED Lightbar Wiring
Windshield LED Lightbar Wiring
Rear LED Lightbar Wiring
High-Voltage Power Amplier Wiring
2-in-1
Wire Harness
Wiring
Diagram
Fig. 5 Fig. 8
High-Voltage Power Amplifier Operation
Default Setting: Low Beam Mode
High-Voltage Power Amplifier Mode Selection
Use the Mode Select button on the high-voltage power amplifier to toggle through the different lighting modes (from Low Beam Mode to High Beam
Mode to Daytime Mode).
FRONT GRILL
LIGHT BAR TEMPLATE REAR
LIGHT BAR TEMPLATE
ABCD
Connector Channel Default Connection Default Setting
A 1 Front Grill Low Beam Headlights On
2 Front Grill High Beam Headlights O
B 3 Low Beam Windshield Lights On
4 High Beam Windshield Lights O
C 5 Tail Lights On*
6 Brake Lights On when braking
D 7 Class Lights On
8 Not used N/A
Connector Channel Default Connection Low Beam Mode High Beam Mode Daytime Mode
A 1 Front Grill Low Beam Headlights On O O
2 Front Grill High Beam Headlights O On O
B 3 Low Beam Windshield Lights On O O
4 High Beam Windshield Lights O On O
C 5 Tail Lights On On O
6 Brake Lights On when braking On when braking On when braking
D 7 Class Lights On On On
8 Not used N/A N/A N/A
Change the high-voltage power amplifier settings and gain access to
additional functions using the Traxxas Link App (available in the Apple
App StoreSM or on Google Play™). The TQi transmitter with the Traxxas
Link Wireless Module (part #6511, sold separately) are required.
Mode Select
Button
*To race the truck without tail lights, disconnect the in-line connector on the rear LED
light bar wire harness.
App Store is a service mark of Apple Inc. Google Play is a trademark of Google Inc.

Front Wiring Diagram
Front Grill LED Light Bars installed Rear LED Light Bar installed