Thank you for choosing the E-Z Swing Metal Detector
Harness. This harness was designed for treasure hunters
by a treasure hunter.
It is a total ensemble consisting of a strong web belt, a
mesh bottom treasure and trash pouch, a uniquely designed
fatigue free harness, and a nice mesh carrying bag. It’s
designed to help you swing your heavy metal detector
without fatigue.
OVERVIEW
The E-Z Swing works by distributing the weight to your
waist. Two flexible crossed bands and shoulder pads make
it comfortable without tiring neck or shoulders.
It is designed to help ease the strain put on the arms and
shoulders as you’re swinging that heavy detector. It allows
you to completely relax your arm and make perfect swings
all day long.
Two straps secure the web belt to your normal belt thereby
counterbalancing the weight of your detector and tools on
your belt. It can easily adjust to fit any body size, detector
swinging method, and even right or left handed people.
ADJUSTMENT
In the front are two straps that can be adjusted for length
as well as allowing you to shift the ring, where they join, to
the left or to the right side of your body depending on which
arm you use to swing your detector.
By shortening the right strap
and lengthening the left strap,
the ring moves to your right
side. Reverse this if you are
left-handed.
Attached to the ring where they
join is a single strap that clips
to the “D” ring you mount on
your detector (See “D-Ring
Attachment” in box).
By adjusting the length of this strap you can set the desired
swinging height of you detector. Simply hold your detector
in the position you normally swing and shorten the strap
until the detector just rises above the ground, then close
the buckle in this position.
As you’re hunting slight adjustments can be easily made.
E-Z SWING HARNESS SPECIFICATIONS
2” wide belt • Adjustable
Shoulder Straps • Adjustable
D-Ring Attachments • Included for 2 detectors
Collection Pouch • Included
Storage bag • Included
Warranty • 1 year
Specifications are subject to change without notice.
Other Equipment by Treasure Products, Inc.
Vibra-Tector - Pulse Induction Metal Detector
Vibra-Quatic - Pinpointer Metal Detector
Vibra-Probe - Pinpointer Metal Detector
WEB BELT
The belt is unique in its own way. It may be worn with or
without the harness assembly. It attaches using Velcro,
not difficult buckles, and can carry the pouch and any of
your existing digging or pinpointing tools.
The large ring on the back will accommodate most straight
handle tools such as picks or hammers.
Note: There are two specially
designed hook and loop
straps located at the back
of the E-Z Swing belt. The
straps are designed to wrap
around and lock the E-Z
SWING belt in place on top
of your own existing belt. The
straps help to keep the belt in
the most comfortable position
when using the harness
attachment.
CARRYING POUCH
The pouch is designed with two
compartments. The large open one for
your trash and the small secured one
for your treasures. Each section has a
perforated mesh bottom to allow the dirt or
water to filter out depending if you’re land
or water hunting. It can also be used with
any other belt.
SHOULDER HARNESS
The harness is designed with elastic straps on the back
that absorb the stress of your detector swing.
There are two shoulder pads that
can be located, as you wish, for
comfort and the Harness can be
easily attached or removed from
the Web Belt.
E-Z Swing
Metal Detector Harness
TM
D-Ring Attachment
Enclosed are two D-Rings & four
Tie-Wraps for mounting the D-
Rings to your detector. The rings
can be placed in two locations on
one detector or on two different
detectors. Try different locations
until the right balance is achieved
when swinging the detector with
your E-Z Swing. Made in USA
www.TreasureProducts.com
