TreeTop Products PINNACLE User manual

REV. #1 12/6/22
PINNACLE 4 FT
TABLE INSTRUCTIONS

QTY. 2
P/N ATB-P0201
QTY. 2
P/N ATB-P0186
QTY. 2
P/N ATB-P0185
QTY. 3
P/N ATB-P0197
QTY. 2
P/N ATB-P0198
QTY. 2
P/N ATB-A0068
QTY. 1
P/N ATB-P0188
QTY. 1
P/N ATB-P0199
QTY. 2
P/N ATB-P0195
A
B
C
D
E
F
G
H
I
REQUIRED TOOLS
(NOT INCLUDED)
1 - 9/16" WRENCH
1 - 9/16" SOCKET
1 - RUBBER MALLET
1 - #2 SQUARE DRIVE BIT
1 - 6mm ALLEN WRENCH
PINNACLE 4 FT
TABLE INSTRUCTIONS
PARTS
REQUIRED
2/10

J
N
QTY. 4
1/4"-20 X 4" BUTTON
HEAD MACHINE SCREW
QTY. 2
3/8" X 2-1/2" HEX BOLT
QTY. 4
3/8" FLAT WASHER
QTY. 2
3/8" LOCKING NUT
QTY. 52
1/4" FLAT WASHER
QTY. 46
1/4"-20 X 1-1/4", BUTTON
HEAD MACHINE SCREW
K
L
M
Q
P
R
QTY. 2
1/4"-20 X 3" BUTTON
HEAD MACHINE SCREW
QTY. 8
CAMS
CAMS MUST BE
ORIENTED IN THIS
DIECTION WHEN
INSTALLED
S
QTY. 4
DECK SCREW
PINNACLE 4 FT
TABLE INSTRUCTIONS
HARDWARE
3/10

A
B
C
P
M
R
M
N
STEP ONE: ON A CLEAN AND LEVEL SURFACE
LAY LOWER PORTION OF END FRAME (C)
FLAT. INSERT UPPER PORTION OF END FRAME
(B) INTO LOWER PORTION. GENTLY TAP WITH
RUBBER MALLET IF NECESSARY TO FULLY ENGAGE.
PLACE GUSSET (A) ONTO END FRAME PARTS AS
SHOWN. THREAD IN (2) 4" MACHINE SCREWS (P)
OVER WASHERS (M). FULLY TIGHTEN (P).
NEXT, ATTACH (4) CAMS TO THE LOWER LEG SECTION
USING 1-1/4" MACHINE SCREW (N) AND FLAT WASHER
(M) AS SHOWN. BE SURE TO ATTACH THEM IN THE
CORRECT ORIENTATION. HAND TIGHTEN USING ALLEN
WRENCH. DO NOT USE POWER TOOLS! DO THE SAME
FOR THE OTHER END FRAME.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ASSEMBLE
END FRAMES
4/10

F
A
B
C
DETAIL AV
SCALE 1 : 4
STEP TWO: WITH THE HELP OF A SECOND PERSON,
HOLD BOTH END FRAMES IN THE UPRIGHT POSITION
ABOUT 36" APART. LOWER SEAT SUPPORT (F) DOWN
INTO SLOTS IN THE END FRAMES. CAMS MAY NEED
TO BE ROTATED IN THE POSITION PICTURED BELOW TO
SLIDE THE SUPPORTS INTO PLACE. LOOSEN CAM SCREW
SLIGHTLY IF THEY DO NOT ROTATE FREELY. GENTLY TAP
THE SUPPORTS IN PLACE WITH A RUBBER MALLET IF
NECESSARY.
WHEN SUPPORT IS IN PLACE, ROTATE THE CAMS
CLOCKWISE TO LOCK SUPPORTS IN PLACE. TIGHTEN
CAM SCREWS USING AN ALLEN WRENCH. HAND TIGHTEN
ONLY. DO NOT USE POWER TOOLS. REPEAT FOR THE
OTHER SEAT SUPPORT.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ASSEMBLE
SEATING
SUPPORT
5/10

J KK L
STEP THREE: ATTACH THE ENDS OF THE TWO GUSSETS (A)
TO EACH OTHER USING 3/8" BOLTS (J), FLAT WASHERS (K),
AND LOCKING NUTS (L). RUN NUT ONTO BOLT BUT DO
NOT TIGHTEN FULLY YET.
PINNBACLE 4 FT
TABLE INSTRUCTIONS
ATTACHING
GUSSETS TO
EACH OTHER
6/10

H
S
S
STEP FOUR: WITH HELP FROM ANOTHER PERSON, ROLL
THE TABLE UP ONTO ONE OF IT'S ENDS. WITH ONE
PERSON HOLDING THE TABLE STEADY, ATTACH THE
LOWER LEG BRACE INTO THE NOTCHES AT THE LOWER
EDGE OF THE END FRAMES. MAKE SURE THE
COUNTERSUNK HOLES FACE OUT. ATTACH USING (4)
#10 X 2-1/2" FLATHEAD SCREWS (S). HAND TIGHTEN.
DO NOT USE POWER TOOLS.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ATTACHING LOWER
LEG BRACE
7/10

M
N
D
I
G
STEP FIVE: ASSEMBLE THE TOP AS ONE UNIT BEFORE
ATTACHING IT TO THE TABLE. LAY SLATS (D) ON CLEAN,
LEVEL SURFACE. ATTACH END CLEATS (I) AND CENTER
SUPPORT (G)AS SHOWN USING (6) 1-1/4" BUTTON HEAD
SCREWS (N) AND (6) FLAT WASHERS (M) PER SLAT. SNUG
THE SCREWS DOWN LIGHTLY BUT DON'T TIGHTEN YET.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ASSEMBLE TOP
SUBASSEMBLY
8/10

M
N
Q
STEP SIX: PLACE TABLE TOP ASSEMBLY ONTO TABLE.
CAREFULLY TAP INTO PACE WITH A RUBBER MALLET
IF NECESSARY TO ALIGN HOLES. START EACH 1/4"-20
MACHINE SCREW (N) OR (P) A FEW THREADS BEFORE
GOING BACK TO TIGHTEN ALL OF THEM. USE 1/4"
FLAT WASHER (M) WITH EACH SCREW AS SHOWN.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ATTACH TOP
TO TABLE
9/10

N
M
E
STEP SEVEN: ATTACH THE (2) SEAT SLATS (D) USING (12)
1-1/4" SCREWS (N) AND (12) FLAT WASHERS (M). GO
BACK AND CONFIRM ALL SCREWS ARE FULLY TIGHTENED.
NO NOT USE POWER TOOLS.
CONGRATULATIONS. YOU HAVE ASSEMBLED YOUR
PINNACLE 4 FT TABLE.
PINNACLE 4 FT
TABLE INSTRUCTIONS
ATTACH SEATING
SLATS
10/10

31.250
59.500
48.000
17.750
9.800
29.900
REV. #1 10/4/22
ALL DIMENSIONS ARE SHOWN IN INCHES
CONSTRUCTION MATERIALS:
Marine Grade Polymer
HARDWARE:
Stainless Steel
PINNACLE 4 FT
TABLE INSTRUCTIONS