Trend Micro Cloud Edge 70 G2 User manual

TREND MICROTM
Cloud Edge 70 G2 Routing Mode/Bridge Mode
Trend Micro Cloud Edge is a next generation security solution for MSPs (Managed
Service Provider) that combines on-premises and cloud-based security features. Deploy
your Cloud Edge 70 G2 on-premises and the MSP can remotely manage your network
through the cloud.
Deployment Modes
3
Opening and Inspecting the Carton
1
Verify that the Cloud Edge gateway carton contains the following items:
Deployment Checklist
4
1. Toggle the switch on the back panel as needed.
2. Connect the Cloud Edge gateway to a power source.
3. Power on the Cloud Edge gateway.
Setting up the Hardware
5
Power
Bridge Routing
Reset
1. Connect the WAN1 port to a wide area network (i.e. Internet).
2. Connect the LAN1 port to an internal endpoint (Bridge Mode) or an internal
network (Routing Mode).
3. Power on the Cloud Edge gateway.
Connecting to the Network
6
Requirement Details
Connect to MGMT and WAN ports.
Bridge Mode:
 Connect LAN1 to internal endpoint.
Routing Mode:
 Connect LAN1 to internal network.
Bridge Mode:
 Internal address for virtual interface (sw0): DHCP or Static
(IP address, netmask, gateway)
Routing Mode:
 External address for WAN1: DHCP, Static, or PPPoE (user
name/password)
 Internal address for LAN1 (Static)
Bridge Mode:
 Your network DNS server IP addresses.
Routing Mode:
 Your network DNS server IP addresses if not assigned by
ISP
Laptop with the following:
 Adobe™Flash™10 or later
 Supported web browser
• Firefox™70 or later
• Google™Chrome 78 or later
• Internet Explorer™11
Ethernet cables (3)
IP addresses (1-2)
DNS settings
Laptop with Ethernet
port
Mode Description
Gateway acts as a transparent layer 2 device, providing scan and threat
protection without interrupting traffic flow. Also functions as a hardware
switch. WAN1 connects to the Internet and seven LAN ports connect
directly to endpoints.
Gateway is visible on the network and acts as a layer 3 routing device with
traffic scanning and control capabilities.
Bridge
Routing Bridge Mode
Routing Mode
Power Cord
Opening and Inspecting the Carton
1
Documents
AC adapter
Serial cable
Verify that the Cloud Edge gateway carton contains the following items:
Ethernet cable
Examining the Cloud Edge Gateway
2
Cloud Edge Gateway Front Panel
Cloud Edge Gateway Back Panel
Cloud Edge Gateway
Router
Internet
WAN
LAN1 LAN2 LAN3 LAN7
...
Cloud EdgeCloud Edge
......
Bridge Mode
LAN
...
Switch
Cloud Edge
Cloud Edge
Routing Mode
WLAN
WAN
Internet
Internet
AC Adapter
Endpoint
100 - 240V AC
InternetModem/Router
Management
Laptop
AC Adapter
100 - 240V AC
Internet
Management
Laptop
Internal
Switch
Note: Cable connectors and colors may vary depending on product version.

© 2021 Trend Micro Incorporated. All Right Reserved. Trend Micro and the t-ball logo are
trademarks or registered trademarks of Trend Micro Incorporated. All other company and/or product
names may be trademarks or registered trademarks of their owners. Information contained in this
document is subject to change without notice.
Item Code: APEQ59161/201125
Cloud Console LED Status
Gateway cannot communicate with the Internet.
No light
Gateway is not registered or cannot communicate with
Cloud Edge Cloud Console. Contact your managed service
provider for assistance.
Blinking green
Gateway is registered and communicating with Cloud Edge
Cloud Console.
Solid green light
The Green LED (Light-Emitting Diode) on the front panel shows the deployment status.
Verifying Connectivity
9
Green LED
Yellow LED
TREND MICROTM
Cloud Edge 70 G2 Routing Mode/Bridge Mode
Routing Mode
1. In the Uplink configuration section, specify information for the WAN interface.
 DHCP
 PPPoE: Specify user name and password.
 Static: Specify IPv4 address, netmask, and gateway.
2. Specify DNS server IP addresses (if not assigned by DHCP or PPPoE).
3. Under System settings section:
a. Specify a FQDN in the Host name field.
b. Configure time settings.
 Automatically: Select Enable NTP server and enter the NTP server IP address.
 Manually: Select Manually set time and enter time in the Local time field.
4. Click Start Configuration Test to verify and then click Save & Register.
5. Click on the Cloud Edge On-Premises Console link.
6. Go to Network Interfaces.
7. Click the LAN1 interface, select L3 type, and configure IP address settings.
 DHCP
 Static: Specify IPv4 address, netmask, and optionally, a gateway.
8. Click Apply.
After logging on for the first time, the Quick Setup screen opens automatically.
Perform one set of initial configuration steps below - either for Bridge Mode or for
Routing Mode, depending on the deployment mode you chose.
Bridge Mode
1. In the Uplink configuration section, specify information for sw0.
 DHCP
 Static: Specify IPv4 address, netmask, and gateway.
2. Specify DNS server IP addresses (if not assigned by DHCP).
3. Under System settings section:
a. Specify a FQDN in the Host name field.
b. Configure time settings.
 Automatically: Select Enable NTP server and enter the NTP server IP address.
 Manually: Select Manually set time and enter time in the Local time field.
4. Click Start Configuration Test to verify and then click Save & Register.
Performing the Initial Configuration
8
Note: You can modify the Intranet Security mode after initial deployment using
Cloud Edge Cloud Console. You cannot modify which interfaces are
included in the switch.
Logging on the Web Console
1. Open a supported web browser.
2. Go to the URL: https://setup.cloudedge or https://192.168.252.1:8443.
3. Specify the logon credentials.
 User name: admin
 Password: adminCloudEdge
4. Press Enter or click Log On.
7
Management laptop
Deployment mode: Bridge Mode
Quick Setup
Uplink configuration
This setup enables you to quickly configure your Cloud Edge applia
Deployment mode: Routing Mode
Uplink configuration
Quick Setup
This setup enables you to quickly configure your Cloud Edge applia
© 2020 Trend Micro Incorporated. All Right Reserved.
Register Cloud Edge with Cloud Edge Cloud Console
After your MSP creates an account for you, you will receive an email with a link to
access Customer Licensing Portal (CLP).
1. Open the email sent from Trend Micro.
2. Log in to CLP using the account information provided in the email.
3. In the Products/Services screen of CLP, click Open Console to open the Cloud
Edge Cloud Console.
4. If your product has not been registered, register the product using the gateway
serial number located on the gateway appliance.
10
1. Power on the Cloud Edge gateway and wait for the system to start.
2. Press and hold the reset button located on the back panel for about 10
seconds until the yellow reset LED on the front panel starts to blink.
3. Release the reset button. The gateway starts the factory reset. The gateway
will restart two times during this process.
Restore the Cloud Edge gateway to factory settings to reconfigure your network
settings or to decommission hardware. The yellow LED on the front panel shows
the factory settings restore status.
Restoring Factory Settings
11
Cautions
1. Lithium Battery Caution
 There is risk of explosion if the battery is replaced by an incorrect type.
 Dispose of used batteries according to the instructions.
 Installation should be performed only by a skilled person who knows all
installation and applicable device specifications.
 Do not carry power supplies by the handle when moving to another place.
 Please conform to your local laws and regulations regarding safe disposal of
lithium batteries.
 Disposal of a battery into a fire or a hot oven, or mechanically crushing or
cutting of a battery can result in an explosion.
 Leaving a battery in an extremely high temperature environment can result in an
explosion or the leakage of flammable liquid or gas.
 A battery subjected to extremely low air pressure may result in an explosion or
leakage of flammable liquid or gas.
2. Grounding Caution
This equipment must be grounded and the power cord for the product should be
connected to a socket outlet with a grounded connection.
12
Cloud Edge Website:
https://www.trendmicro.com/en_us/small-business/cloudedge-network-security.html
Cloud Edge Documents Website:
http://docs.trendmicro.com/en-us/smb/cloud-edge.aspx
List of worldwide offices and phone numbers:
http://www.trendmicro.com/us/about-us/contact/index.html
Contact Information
13