TRENDnet TEG-PCITXR User manual

Quick Installation Guide
TEG-PCITXR
TEG-PCITXRL
3.14

Table of Contents
Version .05.201105
English 1
1. Before You Start
2. How to Install 2
1
Troubleshooting 4

1. Before You Start
Ÿ
ŸCD-ROM Drive
ŸNetwork Cable
32-bit PCI 2.1 slot
Package Contents
Ÿ
ŸCD-ROM (Drivers)
ŸMulti-Language Quick Installation Guide
TEG-PCITXR/TEG-PCITXRL
System Requirements
1
CPU Memory
Windows Vista (32/64-bit)
Windows 7 (32/64-bit)
Windows XP (32/64-bit) /
2003 Server / 2000 / ME / 98SE
800MHz or above
1GHz or above
300MHz or above
512MB RAM or above
1GB RAM or above
256MB RAM or above
Supported Operating Systems

2
2. How to Install
1. Insert the Driver CD-ROM into your computer's
CD-ROM Drive.
4. Follow the InstallShield Wizard instructions.
Note:
1. For Windows 7, please skip to step 7. For Windows Vista/XP/2000, continue on to
step 1.
2. Do not insert the TEG-PCITXR/TEG-PCITXRL until instructed to do so.
2. Click Run autorun.exe (Windows Vista only)
3. Click Install Driver.
5. Click Yes (Windows 2000 only).
6. Click Finish.

3
7. Shutdown your computer and then open your
computer’s Case.
10. Click Yes (Windows 2000 only)
Your installation is now complete.
11. Connect one end of a network cable to one of
the network ports on your modem, router or
switch. Connect the other end of the cable to
the TEG-PCITXR/TEG-PCITXRL’s network
port.
8. Insert PCI Card firmly into an available PCI slot,
and then turn ON the computer and wait until
the Windows desktop appears.
9. Drivers will install automatically.

1. I inserted the Driver CD-ROM into my computer's CD-ROM drive and the installation menu
does not appear automatically. What should I do?
1. For Windows 7, if the installation menu does not appear automatically, click on the
Windows Icon on the bottom left hand corner of the screen, click the “Search programs
and files” box, and type D:\autorun.exe, where “D” in “D:\autorun.exe” is the letter
assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard.
2. For Windows Vista, if the installation menu does not appear automatically, click Start,
click the Start Search box, and type D:\autorun.exe where "D" in "D:\autorun.exe" is the
letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard.
3. For Windows 2000/XP, if the installation menu does not appear automatically, click Start,
click Run, and type D:\autorun where "D" in "D:\autorun.exe" is the letter assigned to
your CD-ROM Drive, and then press the ENTER key on your keyboard.
2. Windows doesn’t recognize my new hardware. What should I do?
1. Verify that your computer meets the system requirements as specified in Section 1.
2. Access your device manager to make sure the adapter is installed properly.
1. To access the device manager on Windows 7, click on the Windows icon on the
bottom left-hand corner, click Computer, click System Properties and then click
Device Manager.
2. To access the device manager on Windows Vista, right-click Computer, click
Properties and then click Device Manager.
3. To access the device manager on Windows XP, right-click My Computer, click
Properties, click the Hardware tab, and then click Device Manager.
If you see a networking device with a yellow question mark or exclamation point:
1. Uninstall the device from device manager
2. Shutdown the computer.
3. Remove the adapter from the computer
4. Reinstall the adapter. See Section 2. How to Install.
3. If the device manager fails to recognize the presence of a new networking adapter, verify
that the network adapter is firmly seated in the PCI slot.
4. Plug the adapter into another PCI slot on your computer.
3. Windows recognizes my new hardware, but I’m unable to connect to my network. What
should I do?
Verify that the RJ-45 Ethernet Cable is securely connected from your switch or router to
your network adapter.
2. Verify that the LEDs on your network card are lit.
3. Verify that the TCP/IP settings are set to Obtain an IP address automatically (see the
steps below).
1.
Troubleshooting
4

Troubleshooting
5
Windows Vista
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Obtain
an IP address automatically.
Windows 7
1. Go into the Control Panel, click Network and
Internet, click Network and Sharing Center,
click Change Adapter Settings and then
right-click the Local Area Connection icon and
then click Properties.
1. Go into the Control Panel, click Network and
Internet, click Network and Sharing Center,
click Manage Network Connections and then
right-click the Local Area Connection icon
and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Obtain
an IP address automatically.

Troubleshooting
19
Troubleshooting
6
Windows XP/2000
1. Go into the Control Panel, double-click the
Network Connections icon and then right-click
the Local Area Connection icon and then click
Properties.
2. Click Internet Protocol (TCP/IP) and then
click Properties. Then click on Obtain an IP
address automatically.
4. How do I install the drivers on Windows 98 or ME?
Please refer to the Help folder on the Driver CD-ROM.
5. Why am I only getting a network connection speed of 100Mbps instead of 1000Mbps?
1. Check the Ethernet Cable. Make sure you are using CAT-5e or CAT-6 Ethernet Cables.
Some CAT-5 cables are not rated to run in Gigabit.
2. Make sure you are connected to a 1000Mbps switch.
If you still encounter problems or have any questions regarding the TEG-PCITXR/TEG-PCITXRL,
please refer to the User's Guide included on the Driver CD-ROM or contact Trendnet's Technical
Support Department.