TRENDnet TE100-P21 User manual

TE100-P21/TEW-P21G Windows 7 Installation Instruction
1. Go to
Hardware Installation
http://www.trendnet.com/downloads/ to download the Windows 7 Utility. Save the file to
your desktop.
2. Right click on the file and select Extract All. Followthewizard to uncompress the file.
3. Connect a RJ-45 Network cable froma switch/router to the LANportof the PrintServer
4. Connectthe detachable antenna (forTEW-P21G only)
5. Connectthe ACpoweradapterto the PrintServer and then to a power outlet
6. Connect the Printer to the USB or parallel port on the Print Server
7. Power on the Printer
Configure the Print Server
1. Double click on PSUtilitySetup_v3.13.exe
2. Followthe stepsto configure the Print server
b. Click OK
a.Select the Print Server and
click Change IP Address.
Manually assign the IP
Address of the Print
Server and then click OK.
Note:TheIPAddress must
match the network
segment of your network.

e. Unplug the Ethernet cable
and the power adapter from
the print server. Wait 15
seconds, then plug the power
adapter back in (TEW-P21G
only).
d. Click on Configuration,
then Wireless. Select the
proper SSID and then click
Save.(Enableand enter the
encryption key if your
wireless network is
encrypted. Please contact
your Network Administrator
for the encryption
key)(TEW-P21G only).
c. Click Show Web Setup.

1. Double click on PSWizardSetup_v2.20.exe
Add the Printer to your computer
2. Follow the steps to add the printer to your computer
b. Click Select from
manufacturer list.
Select the
appropriate driver for
your printer and then
click Next.
a. Select the print server, select
thedesiredportandthenclick
Add Printer.
Note:
1. If your printer is connect to
USB1, select
PS-XXXXXX-U1. If your
printer is connected to
USB2, select
PS-XXXXXX-U2. If your
printer is connected to
LPT, select
PS-XXXXXX-P3.
2. PS-XXXXXX represents
the Server Name of your
print server. Your print
server will have a different
Server Name.

c. Click Next.
d.ClickPrint Test Page.
e. Click OK.

g. Repeat the above steps to add the
printer to other computers on the
network
f. Click Finish.

Troubleshooting
The PS Wizard / PS Utility is unable to see my printer server. What should I do?
1. Double check your hardware connections; make sure that the print server and printer are poweredON
and are properly connected.
2. Click Discover.
3. Disable any software firewall programs (e.g. ZoneAlarm). Also, disable the built in Windows firewall
program.
My printerdoes not print the entire document. What should I do?
Windows 7
1. Click on the Windows icon on the bottom left-hand corner of the screen.
2. Click Devices and Printers.
3. Right click on the printer and select Printer Properties.
4. Click the Advanced tab.
5. Uncheck Enable advanced printing features.
6. Click Apply.
7. Click OK.
I successfully added a printer to my computer and I can print a test page, but I cannot print anything from
Microsoft Word or other applications.
Make sure the printer is set as your default printer. Click the Windows icon ->Devices and Printers and verify
that your printer icon has a check on it.
I configured my print server to automatically receive an IP Address from a DHCP server, and now I cannot go
into the Print Server’s web utility.
Open PS Wizard (See Add the Printer to your PC) to locate your print server’s IPAddress.
After I successfully configured the TEW-P21G to match my wireless network settings, I can not print through
the Print Server.
1. Verify that the wireless settings match your wireless network settings.
2. Verify that the antenna is attached to the Print Server and the WLAN LED on the Print Server is lit.
I forgot the administration password. How do I reset my print server?
Factory reset the print server using the following procedure. This procedure will reset all settings to default.
By default, there is no password.
1. Take a pin or paper clip and press the reset button. The reset button is located on the back of the unit.
2. Wait 15 seconds, then let go.