TRENDnet EL-HS800 User manual

EL-HS800
Quick Installation Guide

1. How to Install
English
1
2. Remove the thumbscrew and
protective plating from the goose
neck wall mount.
1. Rotate the EL-HS800's cover
counter-clockwise to begin cable
installation.
3. Run all necessary cables (CAT 5
cable, Power Adapter cable, and
the EL-HS800's power terminals)
through the goose neck wall
mount. When using a wireless
camera, please run the Antenna
cable also.
Version 01.18.2006

English
2
5. After inserting the appropriate
cables, extend each cable to 6
inches for camera installation.
4. Run each cable through the
opening located at the top of the
EL-HS800. DO NOT run all cables
through the opening
simultaneously. Serious blockage
can occur.
6. Caution: Before cutting any power
cord, make sure that the power
cord is NOT PLUGGED into an
electrical source. Now take a
power cord with a two-prong plug
and cut the wire.

English
3
7. Use a precision knife or a sharp
object to split the wire in two
halves.
8. Peel the plastic sheath to expose
the copper wiring. It is
recommended that you use a wire
stripper to remove the plastic
sheath effectively.
9. You should have two halves of
exposed copper wire as shown
below.

4
English
12. Repeat steps 10-11 for the next
pair of terminals.
13. Pull in the power terminals into
the goose neck wall mount.
10. Pair one half of the power cable
with the red terminal of the
enclosure's power supply.
11. Place the yellow wire connector
over the assembly in step 10, and
twist the wire connector clockwise
to secure the contact between the
wired pair.

5
English
16. Take the circular base and
connect three 2-inch Mounting
screws and three nuts to create
this assembly.
14. Slide the protective plating into
the goose neck wall mount and
tighten the thumb screw.
15. Screw the goose neck wall mount
on top of the EL-HS800 with an
Alan wrench and three hexagon
socket screws.
View from below
View from above

6
English
19. Take the TV-IP400/TV-IP400W
and turn to the bottom of the
camera. Remove the rubber
molding to prepare the camera for
the mounting.
20. Attach the mounting plate for the
camera with a small screw.
18. Take the assembly in step 18, and
use three countersunk head
screws to mount the assembly on
top of the 2-inch mounting
screws.
17. Mount the assembly in step 16
using three screws.

7
English
21. Take the assembly in step 21 and
mount the assembly on top of the
mounting screws with regular
screws.
22. Place the EL-HS800's cover over
the camera and rotate the cover
clock-wise.

Limited Warranty
TRENDnet warrants its products against defects in material and
workmanship, under normal use and service, for the following lengths of
time from the date of purchase.
EL-HS800 - 1 Years Warranty
If a product does not operate as warranted above during the applicable
warranty period, TRENDnet shall, at its option and expense, repair the
defective product or part, deliver to customer an equivalent product or
part to replace the defective item, or refund to customer the purchase
price paid for the defective product. All products that are replaced will
become the property of TRENDnet. Replacement products may be new
or reconditioned.
TRENDnet shall not be responsible for any software, firmware,
information, or memory data of customer contained in, stored on, or
integrated with any products returned to TRENDnet pursuant to any
warranty.
There are no user serviceable parts inside the product. Do not remove
or attempt to service the product by any unauthorized service center.
This warranty is voided if (i) the product has been modified or repaired
by any unauthorized service center, (ii) the product was subject to
accident, abuse, or improper use (iii) the product was subject to
conditions more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within
the applicable warranty period for a Return Material Authorization (RMA)
number, accompanied by a copy of the dated proof of the purchase.
Products returned to TRENDnet must be pre-authorized by TRENDnet
with RMA number marked on the outside of the package, and sent
prepaid, insured and packaged appropriately for safe shipment.
8

WARRANTIES EXCLUSIVE: IF THE TRENDnet PRODUCT DOES NOT
OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE
REMEDY SHALL BE, AT TRENDnet'S OPTION, REPAIR OR
REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES
ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TRENDnet NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN
CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR
USE OF TRENDnet'S PRODUCTS.
TRENDnet SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS
TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED
DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT,
FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW
TRENDnet ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY
LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT
OF OR IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION
OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY
TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE
PAID, AT TRENDnet’S OPTION. THIS DISCLAIMER OF LIABILITY FOR
DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of
the state of California.
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 Year
Warranty
9