TRENDnet TE100-S16plus User manual

TE100-S16plus
16-Port 10/100Mbps
NWay Fast Ethernet Switch
User’s Guide

FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to
radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will
be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be required
to take adequate measures.
P/N:6012-3216201

i
TABLE OF CONTENTS
ABOUT THIS GUIDE............................................................III
PURPOSE..................................................................................................III
TERMS/USAGE ......................................................................................III
OVERVIEW OF THIS USER’S GUIDE.............................................III
INTRODUCTION.........................................................................1
FAST ETHERNET TECHNOLOGY......................................................1
SWITCHING TECHNOLOGY ................................................................2
FEATURES .................................................................................................3
UNPACKING AND INSTALLATION....................5
UNPACKING..............................................................................................5
INSTALLATION........................................................................................5
100BASE-FX MODULE INSTALLATION.......................................6
RACK MOUNTING..................................................................................7
IDENTIFYING EXTERNAL COMPONENTS
........................................................................................................................15
FRONT PANEL........................................................................................15
REAR PANEL..........................................................................................16
LED INDICATORS................................................................................17

ii
CONNECTING THE SWITCH...................................18
PC TO SWITCH......................................................................................22
HUB TO SWITCH...................................................................................23
A. 10BASE-T Hub..........................................................................23
B. 100BASE-TX Hub....................................................................23
HUB WITHOUT UPLINK (MDI-II) PORT ..................................................23
A. Using straight through cable...................................................23
B. Using crossover cable................................................................24
SWITCH TO SWITCH (OTHERDEVICES)...................................................24
A. Using straight through cable...................................................24
B. Using crossover cable................................................................24
PORT SPEED & DUPLEX MODE.....................................................25
TECHNICAL SPECIFICATIONS............................19
RJ-45 PIN SPECIFICATION.........................................21

iii
ABOUT THIS GUIDE
Congratulations on your purchase of the 16-port 10/100M NWay Fast
Ethernet Switch. This device integrates 100Mbps Fast Ethernet and
10Mbps Ethernet network capabilities in a highly flexible package.
Purpose
This guide discusses how to install your 16-port 10/100Mbps NWay
Fast Ethernet Switch.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to your
16-port 10/100M NWay Fast Ethernet Switch, and ”switch” (first
letter lower case) refers to other Ethernet switches.
Overview of this User’s Guide
Introduction. Describes the Switch and its features.
Unpacking and Installation. Helps you get started with the basic
installation of the Switch.
Identifying External Components. Describes the front panel, rear
panel and LED indicators of the Switch.
Connecting the Switch. Tells how you can connect the Switch to your
Ethernet network.
Technical Specifications. Lists the technical (general, physical and
environmental, and performance) specifications of the Switch.
RJ-45 Pin Specification. Describes the RJ-45 receptacle/connector
and the straight through and crossover cable connector.

1
INTRODUCTION
This chapter describes the features of the Switch and some
background information about Ethernet/Fast Ethernet switching
technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of
desktop computing applications are fueling the need for high
performance networks. A number of high-speed LAN technologies
have been proposed to provide greater bandwidth and improve
client/server response times. Among them, 100BASE-TX (Fast
Ethernet) provides a non-disruptive, smooth evolution from the
current 10BASE-T technology. The non-disruptive and smooth
evolution nature, and the dominating potential market base, virtually
guarantee cost effective and high performance Fast Ethernet solutions
in the years to come.
100Mbps Fast Ethernet is a new standard specified by the IEEE 802.3
LAN committee. It is an extension of the 10Mbps Ethernet standard
with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the Switch is
compatible with all 10Mbps Ethernet environments, it provides a
straightforward upgrade and takes advantage of the existing
investment in hardware, software, and personnel training.

2
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology
is the development of switching technology. A switch bridges and
transmits Ethernet packets at the MAC address level of the Ethernet
protocol, among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch
increases capacity and decreases network loading by dividing a local
area network into different segments. Each segment has its own
bandwidth and it does not compete with others for network
transmission capacity.
Aswitch acts as a high-speed selective bridge between the individual
segments. The switch forwards traffic from origin segment to
destination segment, without interfering with any other segments. By
doing this, the total network capacity is multiplied, while still
maintaining the same network cabling and adapter cards.
For Fast Ethernet networks, a switch is an effective way of eliminating
problems of uplinking Fast Ethernet hubs beyond the “two-repeater
limit”. A switch can be used to split parts of the network into different
collision domains, making it possible to expand your Fast Ethernet
network beyond the 205-meter network diameter limit. The switch
supports both traditional 10Mbps Ethernet and 100Mbps Fast
Ethernet, which is also ideal for bridging between the existing
10Mbps networks and the new 100Mbps networks.
LAN Switching technology is a marked improvement over the
previous generation of network bridges, which were criticized by their
higher latencies. Routers have also been used to segment local area
networks. But, the router expensive, difficult to setup, and

3
maintenance intensive, these make it relatively impractical for the
network. Switch, on the other hand, is less expensive, easier to setup,
and practically maintenance free, which make it an ideal solution to
today’s local area network congestion problems.
Features
This high performance Switch was designed for a network
environment where traffic and the number of users increase
continuously.
The Switch, with its standard rack-mount size, is perfect for middle to
large workgroups. It provides immediate access to a rapidly growing
network through a wide range of user-reliable functions.
The Switch is ideal for shared bandwidth 10Mbps or 100Mbps
workgroups with multiple high-speed servers. With the highest
bandwidth at 200Mbps (100Mbps full-duplex mode), each port can
provide workstation with congestion-free data-pipe for simultaneous
access to the server.
The Switch is expandable by cascading two or more switches
together. As all ports support 200Mbps, the Switch can be cascaded
from any port and to any number of switches.
The Switch is a perfect choice for 10Mbps network site that could be
upgraded to Fast Ethernet in the future. Ethernet workgroups can
connect to the Switch now, and change adapters and hubs anytime
later without changing the Switch or reconfiguring the network.
The Switch combines dynamic memory allocation with store-and-
forward switching method to ensure that the buffer is effectively
allocated for each port.It also controls the data flowbetween transmit
and receive nodes to guarantee against all possible packet loss.

4
This Switch is an unmanaged 10/100Mbps Fast Ethernet Switch that
offers solutions to increase Ethernet workgroup bandwidth. Other key
features are as followed:
?? Uplink/MDI-II (media dependent interface) port for uplink to
another switch or hub.
?? Store and forward switching scheme. As the result of complete
frame checking and error frame filtering, this scheme prevents
error packages from transmitting among segments.
?? NWay Auto-negotiation for any port. This allows auto-sensing
of speed (10/100Mbps) thereby providing you with automatic
and flexible solutions for your network.
?? IEEE 802.3x flow control for full-duplex mode operation.
?? Back pressure flow control for half-duplex mode operation.
?? Data Forwarding Rate (per port) at wire-speed for both
10Mbps and 100Mbps speed.
?? Data Filtering Rate (per port) at wire-speed for both 10Mbps
and 100Mbps speed; eliminates all error packets, runts, etc.
?? 16K active MAC address entry table with self-learning and
table ageing.
?? 512KBytes RAM buffer per device.
?? Broadcast storm protection.
?? Three QoS levels; checked via IP header, 802.1Q VLAN Tag,
and/or selected per port basis.
?? Supports two trunking groups for cascading two or more
Switches (same model).

5
UNPACKING AND INSTALLATION
This chapter provides unpacking and setup information for the Switch.
Unpacking
Open the shipping cartons and carefully unpacks its contents. The
carton should contain the following items:
One the 16-port 10/100M NWay Fast Ethernet Switch
One AC power cord; suitable for your area’s electrical power
connections
Four rubber feet to be used for shock cushioning
Screws and two mounting brackets
This User’s Guide
If any item is found missing or damaged, please contact your local
reseller for replacement.
Installation
The site where you install the Switch may greatly affect its
performance. When installing, consider the following pointers:
?? Install the Switch in a fairly cool and dry place. See
Technical Specification for the acceptable operating
temperature and humidity ranges.
?? Install the Switch in a site free from strong electromagnetic
source, vibration, dust, and direct sunlight.
?? Leave at least 10cm of space at the left and right hand side of
the Switch for ventilation.

6
?? Install the Switch on a sturdy, level surface that can support
its weight, or on a 19” EIA standard-size equipment rack.
For information on rack installation, please see the next
section, Rack Mounting.
?? When installing the Switch on a level surface, attach the
rubber feet on the corners at the bottom of the Switch. The
rubber feet cushion the Switch and protect the bottom of the
Switch.
100Base-FX Module Installation
The installation procedure for each module is the same. Additional
information about each module is provided in the module’s package.
1. Power off the switch.
2. Locate the module slot at the switch’s rear panel.
3. Using a screwdriver, undo the two screws and remove the dust
cover on the module slot. Note: reinstall the dusk cover when the
slot is empty.
4. Holding the module with the component-side up and connector-
side going into the slot. Gently slide the module along the guides
in the slot and firmly seat it in the internal connector.
5. Using a screwdriver, replace the two screws and tighten them
until snug.
Note:
1. If the module is not present in the module bay, we recommend
you install the dust cover over the module bay.

7
2. The port 16 and the 100BASE-FX port is really the same port.
Do not connect both Port 16 and the 100BASE-FX port at the same
time.
Rack Mounting
The switch can be mounted in an EIA standard-size 19-inch rack,
which can be placed in a wiring closet with other equipment. Attach
the mounting brackets at the switch’s side panels (one on each side),
and secure them with the provided screws.
After that, use screws provided with the equipment rack to mount each
switch in the rack.

15
IDENTIFYING EXTERNAL COMPONENTS
This section identifies all the major external components of the
switch. Both the front and rear panel is shown, followed by a
description of each panel’s feature. The LED indicator panel is
described in detail in the next chapter.
Front Panel
The figure below shows the front panels of the switch.
16-port 10/100Mbps NWay Fast Ethernet Switch
LED Indicator Panel
Refer to the next chapter for detailed information about each LED
indicator.
Twisted-Pair Ports
Use any of these ports to connect network devices (workstations,
hubs, switches, etc.) to the Switch. These ports are MDI-X ports and
you can use ordinary straight-through twisted-pair cables to connect
PCs, workstations, and Servers to the Switch. If you need to connect
these ports to devices with MDI-X ports, you need to use crossover
cables, or connect using the Uplinkport (described below).
Uplink Ports
The Uplink port is a MDI-II port, which means you can connect this
port to another device’s MDI-X port using an ordinary straight-
through twisted-pair cable.

16
Port 8and the Uplink port is really the same port, except that their
pin-outs are different. Do not use both Port 8 and the Uplink port at
the same time.
Rear Panel
Module Slot
Trunk QoS
Trunking setting DIP switch
Qos setting DIP switch
AC power connector
Power switch
Module Slot:
For installing optional fiber module for 100BASE-FX connection.
Trunking setting DIP switch:
By using the trunking DIP switches, you can set the trunking function.
For detail information on how to configure trunking, please refer to
the Trunking Setting in the next section.
QoS setting DIP switch:
By using the QoS DIP switches, you can set the QoS function. For
detail information on how to setup QoS, please refer to the QoS
Setting in the next section.
AC Power Connector:
For the power cord.

17
LED Indicators
Power (Power Indicator)
This indicator lights green when the hub is receiving power.This LED
is off indicating no power.
FX (100BASE-FX Module Indicator (green))
This LED lights green indicating a good link to the installed fiber
module. It remains off when the module is not present.
10/100M FDX and 10/100M COL (10/100Mbps Full-Duplex and
10/100Mbps Collision Indicator)
This LED indicator lights green when the respective port is in full-
duplex (FDX) mode. It remains off for half-duplex operation. This
LED blinks green when collision occurs on the respective port.
Note: the full-duplex LED lights green when the connected device
supports full-duplex operation.
10M Link/ACT and 100M Link/ACT (10Mbps Link/Activity
(amber) and 100Mbps Link/Activity (green) Indicator)
This indicator lights green when the port is connected to a 100Mbps
device. It blinks green when transmitting or receiving data on the
100Mbps network.
This indicator lights amber when the port is connected to a 10Mbps
device. It blinks amber when transmitting or receiving data on the
10Mbps network.

18
Trunking setting
This Switch supports trunking function. Trunking function increases
backbone bandwidth and reduces network congestion; this is helpful
when the traffic is heavy between the cascaded Switches.
You can cascade two Switches via one trunking group (max. of 4
ports) with bandwidth up to 800Mbps;or cascade three (or more)
Switches via both trunking groups with 800Mbps bandwidth between
the Switches. Please see the table and diagrams below for more
information.
You can select to trunk two Switches using 2, 3, or 4 ports with Trunk
Group A or B. Please follow the instructions below to set the trunking
dipswitches:
Note: You can only trunk same model Switches together.
1. Power off the Switch.
2. Follow the table above to select the trunk ports and set the
dipswitches.
3. Repeat step 1 & 2 and configure another Switch.
A0
A1
Trunking Group A
00Disable
01Port 1 &9 (400Mbps)
10Port 1, 2 & 9 (600Mbps)
11Port 1, 2, 9 & 10 (800Mbps)
A2
A3
Trunking Group B
00Disable
01Port 8, 16 (400Mbps)
10Port 8, 15 & 16 (600Mbps)
Trunk
0
1
A
0
A
1
A
2
A
3
11Port 7, 8, 15 & 16 (800Mbps)