TRENDnet PoE Web Smart Switch Series User manual

TRENDnet User’s Guide
Cover Page

© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
a
Thank you for purchasing your new TRENDnet PoE
Web Smart Switch!
Please note: The scope of this user's guide encompasses multiple
products with varying features. Images, artwork, and other specificities
including port count, interfaces etc. may not be identical to the model
you purchased. Please consult the specific model specifications for your
unit for a full list of supported features.
Please ensure your switch’s firmware version is V2.10.010 or newer for
Layer 2+ management features. See the Firmware Upgrade section in
this document for additional information regarding the firmware upgrade
procedure.
Contents
PoE Web Smart Switch Series Product Overview ..............................i
TPE-082WS Overview ......................................................................................................i
Package Contents ..................................................................................................i
TPE-082WS Hardware Features.............................................................................i
TPE-1620WS v2 & TPE-1620WSF Overview...................................................................iii
Package Contents ................................................................................................iii
TPE-1620WS/TPE-1620WSF Hardware Features.................................................iii
TPE-2840WS v2 Overview ..............................................................................................v
Package Contents .................................................................................................v
TPE-2840WS Hardware Features..........................................................................v
TPE-5028WS Overview .................................................................................................vii
Package Contents ...............................................................................................vii
TPE-5028WS Hardware Features........................................................................vii
TPE-5240WS Overview ..................................................................................................ix
Package Contents ................................................................................................ix
TPE-5240WS Hardware Features.........................................................................ix
TPE-5048WS Overview ..................................................................................................xi
Package Contents ................................................................................................xi
TPE-5048WS Hardware Features.........................................................................xi
Switch Installation ..........................................................................1
Desktop Hardware Installation...................................................................................... 1
Rack Mount Hardware Installation................................................................................ 1
Basic IP Configuration.................................................................................................... 2
Connect additional devices to your switch.................................................................... 4
Accessing switch management interfaces........................................5
Access your switch management page.......................................................................... 5
System Info.................................................................................................................... 5
View your switch status information................................................................... 5

© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
b
System............................................................................................7
System Management..................................................................................................... 7
Set your system information ............................................................................... 7
L3 Feature...................................................................................................................... 8
IPv4 Interface....................................................................................................... 8
IPv4 ARP Aging Time ............................................................................................ 9
IPv4 Static ARP..................................................................................................... 9
IPv4 Static/Default Route .................................................................................. 10
Set your IPv6 settings ........................................................................................ 11
Add IPv6 neighbors............................................................................................ 12
Configure IPv6 Routing Table ............................................................................ 13
DNS .............................................................................................................................. 14
Set your DNS server settings.............................................................................. 14
IP Access List................................................................................................................ 15
Restrict access to switch management page..................................................... 15
Administration............................................................................................................. 16
Change administrator password and add accounts........................................... 16
Timeout........................................................................................................................ 17
Change web idle login timeout settings ............................................................ 17
System Time ................................................................................................................ 17
Set the switch date and time............................................................................. 17
SSL................................................................................................................................ 19
Enable HTTPS/SSL (Secure Socket Layer) management access ......................... 19
SSH............................................................................................................................... 20
Enable SSH (Secure Shell) management access................................................. 20
Telnet........................................................................................................................... 21
Enable Telnet management access.................................................................... 21
DHCP Auto Configuration ............................................................................................ 22
Enable DHCP Auto Configuration....................................................................... 22
System Log................................................................................................................... 23
View and setup your switch logging .................................................................. 23
SNMP........................................................................................................................... 24
Settings .............................................................................................................. 24
View................................................................................................................... 25
Group................................................................................................................. 26
User ................................................................................................................... 27
Community ........................................................................................................ 28
Trap.................................................................................................................... 29
RMON .......................................................................................................................... 30
Settings .............................................................................................................. 30
Statistics............................................................................................................. 31
History ............................................................................................................... 32
Alarms................................................................................................................ 33
Events ................................................................................................................ 34
Statistics....................................................................................................................... 36
Traffic................................................................................................................. 36
Error................................................................................................................... 37
IEEE 802.3az EEE.......................................................................................................... 38
Enable IEEE 802.3az Power Saving Mode.......................................................... 38
Network .......................................................................................39
Physical Interface......................................................................................................... 39
Configure Physical Interfaces ............................................................................ 39
Spanning Tree.............................................................................................................. 41
Protocol ............................................................................................................. 41
Port .................................................................................................................... 42
MST.................................................................................................................... 43
Instance ............................................................................................................. 44
MST Port ............................................................................................................ 45
Trunk............................................................................................................................ 46
Settings .............................................................................................................. 46
Status................................................................................................................. 47

© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
c
Port Priority ....................................................................................................... 47
Mirroring...................................................................................................................... 48
Configure port mirror settings........................................................................... 48
Loopback Detection..................................................................................................... 49
Enable loopback detection ................................................................................ 49
Static Unicast ............................................................................................................... 50
Add static unicast entries to the switch............................................................. 50
Static Multicast ............................................................................................................ 51
Add static multicast entries to the switch ......................................................... 51
IGMP Snooping ............................................................................................................ 52
Settings .............................................................................................................. 52
Router Ports....................................................................................................... 53
MLD Snooping.............................................................................................................. 54
Settings .............................................................................................................. 54
Router Port ........................................................................................................ 55
Multicast VLAN ............................................................................................................ 56
Multicast VLAN Settings..................................................................................... 56
Multicast VLAN Table......................................................................................... 56
Multicast VLAN Group Settings ......................................................................... 56
Multicast VLAN Access Settings......................................................................... 57
Multicast Filtering........................................................................................................ 58
Multicast Filtering.............................................................................................. 58
Bandwidth Control....................................................................................................... 58
Storm Control .................................................................................................... 58
Ingress Rate Limiting.......................................................................................... 59
Egress Rate Limiting........................................................................................... 59
VLAN ............................................................................................................................ 60
Tagged ............................................................................................................... 60
Port .................................................................................................................... 61
Forwarding......................................................................................................... 62
Dynamic............................................................................................................. 62
Private................................................................................................................ 63
Current............................................................................................................... 64
GVRP............................................................................................................................ 64
GVRP Global Settings......................................................................................... 64
Port Settings ...................................................................................................... 65
Time Settings ..................................................................................................... 66
Voice VLAN .................................................................................................................. 67
Settings .............................................................................................................. 68
OUI..................................................................................................................... 69
LLDP............................................................................................................................. 70
Enable and configure LLDP ................................................................................ 70
Settings .............................................................................................................. 70
Basic TLVs Settings............................................................................................. 72
Dot1 TLVs Settings............................................................................................. 72
Dot3 TLVs Settings............................................................................................. 72
MED Port Settings.............................................................................................. 73
LLDP Statistics Information................................................................................ 73
LLDP Local Port Information .............................................................................. 73
Neighbor............................................................................................................ 73
MAC VLAN ................................................................................................................... 74
MAC VLAN ......................................................................................................... 74
Protocol VLAN.............................................................................................................. 74
Protocol VLAN Profile ........................................................................................ 74
Protocol VLAN Profile Interface......................................................................... 75
QoS (Quality of Service) ................................................................76
CoS............................................................................................................................... 76
Set CoS priority settings..................................................................................... 76
Port Priority ................................................................................................................. 77
Set Port Priority ................................................................................................. 77
DSCP ............................................................................................................................ 77

© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
d
Set DSCP (Differentiated Services Code Point) Class Mapping settings ............ 77
Scheduling Algorithm................................................................................................... 78
Set the Scheduling Algorithm ............................................................................ 78
IPv6 Traffic Class.......................................................................................................... 79
Configure the IPv6 Traffic Class Settings ........................................................... 79
PoE (Power over Ethernet) ............................................................80
Power over Ethernet.................................................................................................... 80
Configure PoE settings....................................................................................... 81
Time Range .................................................................................................................. 82
Configure PoE Time Range................................................................................. 82
Security.........................................................................................83
Port Access Control...................................................................................................... 83
Configure Port Access Control ........................................................................... 83
Dial-in User .................................................................................................................. 84
Create Dial-In Users (Local Authentication Method)......................................... 84
RADIUS......................................................................................................................... 85
Add RADIUS Servers (RADIUS Authentication Method) .................................... 85
TACACS+ ...................................................................................................................... 86
Add TACACS+ Servers (TACACS+ Authentication Method)................................ 86
Destination MAC Filter ................................................................................................ 87
Destination MAC Filter....................................................................................... 87
Denial of Service .......................................................................................................... 88
Denial of Service (DoS)....................................................................................... 88
DHCP Snooping............................................................................................................ 89
Settings .............................................................................................................. 89
VLAN .................................................................................................................. 90
Interfaces........................................................................................................... 91
Binding............................................................................................................... 92
Dynamic ARP Inspection.............................................................................................. 93
Settings .............................................................................................................. 93
ARP Inspection Validation ................................................................................. 93
ARP Inspection Port Settings ............................................................................. 94
ARP Inspection VLAN ......................................................................................... 94
ARP Inspection Statistics.................................................................................... 95
ARP Inspection VLAN ......................................................................................... 95
ACL............................................................................................................................... 96
ACL Configuration Wizard.................................................................................. 96
Access Profile List .............................................................................................. 97
ACL Finder.......................................................................................................... 98
Tools.............................................................................................99
Firmware Upgrade....................................................................................................... 99
Upgrade your switch’s firmware ....................................................................... 99
Firmware Upgrade via HTTP Settings ................................................................ 99
Firmware Upgrade via TFTP Settings............................................................... 100
Config Backup Restore............................................................................................... 100
Config Backup/Restore .................................................................................... 100
Backup/Restore via HTTP Settings................................................................... 100
Backup/Restore via TFTP Settings ................................................................... 101
Diagnostics................................................................................................................. 102
Cable Diagnostics Test ..................................................................................... 102
Reboot ....................................................................................................................... 103
Reboot/Reset to factory defaults .................................................................... 103
Ping............................................................................................................................ 104
Network Connectivity Test (Ping Tool) ............................................................ 104
Using the Web Smart Switch Management Utility .......................105
System Requirements................................................................................................ 105
Installation................................................................................................................. 105
Using the Utility......................................................................................................... 106

© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
e
Launching the Utility........................................................................................ 106
Discovery List ................................................................................................... 107
Monitor List ..................................................................................................... 107
Device Setting .................................................................................................. 108
Main Menu Options......................................................................................... 109
Hardware Features and Specifications.........................................110
Web Smart Switch Series Software Specifications........................112
Quick Installation GuideTroubleshooting.....................................114
Appendix ....................................................................................115

© Copyright 2018 TRENDnet. All Rights Reserved.
i
TRENDnet User’s Guide
PoE Web Smart Switch Series
PoE Web Smart Switch Series Product Overview
TPE-082WS Overview
TPE-082WS
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power adapter (54V DC, 1.67A)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-082WS Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
Gigabit Ethernet PoE+ Ports (1-8) –Connect either network PoE+ or
non-PoE devices.
SFP Slots (9-10) –Supports optional 1000BASE-SX/LX mini-GBIC modules
for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
ii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
75W or above, the LED will turn on and the system will not
provide power additional PD (PoE client devices) after max
PoE budget is reached.
Off
:
When the PoE power provided is below the 75W PoE
power budget.
Gigabit Ethernet PoE+ Port LEDs (1-8)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
on
:
When the Green LED lights on, the respective port is
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet Port PoE+ LEDs (1-8)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (9-10)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
iii
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-1620WS v2 & TPE-1620WSF Overview
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power cord (1.8 m / 6 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-1620WS/TPE-1620WSF Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
PoE+ Gigabit Ports (1-16) –Connect network PoE+ or non-PoE devices.
Gigabit Ethernet Ports (17-20) –Connect network devices. Ports 17-20
are shared with SFP slots 17F-20F and are disabled when SFP slots (17F-
20F) are in use.
SFP Slots (17F-20F) –Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
iv
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
185W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the PoE power
budget.
Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
Gigabit Ethernet Port LEDs (1-20)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
on
:
When the Green LED lights on, the respective port is
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet PoE+ Port LEDs (1-16)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (17F-20F)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
v
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-2840WS v2 Overview
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power cord (1.8 m / 6 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-2840WS Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
PoE+ Gigabit Ports (1-24) –Connect network PoE+ or non-PoE devices.
Gigabit Ethernet Ports (25-28) –Connect network devices. Ports 25-28
are shared with SFP slots 25F-28F and are disabled when SFP slots (25F-
28F) are in use.
SFP Slots (25F-28F) –Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
vi
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
185W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 185W PoE
power budget.
Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
Gigabit Ethernet Port LEDs (1-28)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
:
When the Green LED lights on, the respective port is
on
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet PoE+ Port LEDs (1-24)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (25F-28F)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
vii
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5028WS Overview
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power cord (1.8 m / 6 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5028WS Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
PoE+ Gigabit Ports (1-24) –Connect network PoE+ or non-PoE devices.
Gigabit Ethernet Ports (25-28) –Connect network devices. Ports 25-28
are shared with SFP slots 25F-28F and are disabled when SFP slots (25F-
28F) are in use.
SFP Slots (25F-28F) –Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
viii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
370W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 370W PoE
power budget.
Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
Gigabit Ethernet Port LEDs (1-28)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
on
:
When the Green LED lights on, the respective port is
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet PoE+ Port LEDs (1-24)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (25F-28F)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
ix
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5240WS Overview
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power cord (1.8 m / 6 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5240WS Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
PoE+ Gigabit Ports (1-48) –Connect network PoE+ or non-PoE devices.
Gigabit Ethernet Ports (49-52) –Connect network devices. Ports 49-52
are shared with SFP slots 49F-52F and are disabled when SFP slots (49F-
52F) are in use.
SFP Slots (49F-52F) –Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
x
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
370W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 370W PoE
power budget.
Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
Gigabit Ethernet Port LEDs (1-52)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
on
:
When the Green LED lights on, the respective port is
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet PoE+ Port LEDs (1-48)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (49F-52F)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
xi
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5048WS Overview
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power cord (1.8 m / 6 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5048WS Hardware Features
Front View
Rear View
Reset Button –Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
Mode Button –Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
PoE+ Gigabit Ports (1-48) –Connect network PoE+ or non-PoE devices.
Gigabit Ethernet Ports (49-52) –Connect network devices. Ports 49-52
are shared with SFP slots 49F-52F and are disabled when SFP slots (49F-
52F) are in use.
SFP Slots (49F-52F) –Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.

© Copyright 2018 TRENDnet. All Rights Reserved.
xii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
740W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 740W PoE
power budget.
Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
Gigabit Ethernet Port LEDs (1-52)
Link/Activity button Mode
Green
on
:
When the Green LED is on, the respective port is
connected to a 1Gbps Ethernet network.
Amber
on
:
When the Green LED lights on, the respective port is
connected to a 10/100Mbps Ethernet network.
Green
Blinking
:
When the LED is blinking green, the port is transmitting or
receiving data on the network at 1Gbps speed.
Amber
Blinking
:
When the LED is blinking amber, the port is transmitting
or receiving data on the network at 10/100Mbps speed.
Off
When the LED is off, the respective port is disconnected.
Gigabit Ethernet PoE+ Port LEDs (1-48)
PoE LED button Mode
Green
on
:
When the Green LED is on, the connected device is
receiving power.
Amber
on
:
When the Amber LED lights on, the connected PoE device
is not receiving power. The cause is either insufficient
power budget, or due to Class/PowerLimit restrictions in
the PoE configurations.
Off
:
When the LED is off, the respective port is either not
connected to a PoE device or is disconnected.
SFP Slots (49F-52F)
Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.

© Copyright 2018 TRENDnet. All Rights Reserved.
1
TRENDnet User’s Guide
PoE Web Smart Switch Series
Switch Installation
Desktop Hardware Installation
The site where you install the hub stack may greatly affect its performance. When
installing, consider the following pointers:
Note: Your switch model may be different than the one shown in the example
illustrations.
Install the Switch in a fairly cool and dry place.
Install the Switch in a site free from strong electromagnetic field generators (such
as motors), vibration, dust, and direct exposure to sunlight.
Leave at least 10cm of space at the front and rear of the hub for ventilation.
Install the Switch on a sturdy, level surface that can support its weight, or in an
EIA standard-size equipment rack. For information on rack installation, see the
next section, Rack Mounting.
When installing the Switch on a level surface, attach the rubber feet to the
bottom of each device. The rubber feet cushion the hub and protect the hub
case from scratching.
Rack Mount Hardware Installation
The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in
a wiring closet with other equipment. Attach the mounting brackets at the switch’s
front panel (one on each side), and secure them with the provided screws.
Note: The switch model may be different than the one shown in the example
illustrations.
Then, use screws provided with the equipment rack to mount each switch in the rack.

© Copyright 2018 TRENDnet. All Rights Reserved.
2
TRENDnet User’s Guide
PoE Web Smart Switch Series
Basic IP Configuration
3. Assign a static IP address to your computer’s network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
4. Open your web browser, and type the IP address of the switch in the address bar, and
then press Enter. The default IP address is 192.168.10.200.
5. Enter the User Name and Password, and then click Login. By default:
User Name: admin
Password: admin
Note: User name and password are case sensitive.
6. Click System, L3 Feature, and then click IPv4 Interface.