TRENDnet TEG-S18TXE User manual

8-Port 1000BASE-T
Gigabit Ethernet Switch
TEG-S18TXE
User’s Guide

FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with this user’s guide, may
cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct
the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.

TABLE OF CONTENTS
ABOUT THIS GUIDE..............................................................................1
TERMS ....................................................................................................1
OVERVIEW OF THIS USER’S GUIDE........................................................1
INTRODUCTION.....................................................................................3
GIGABIT ETHERNET TECHNOLOGY .......................................................3
SWITCHING TECHNOLOGY.....................................................................4
FEATURES ..............................................................................................5
UNPACKING AND SETUP.....................................................................7
UNPACKING ...........................................................................................7
SETUP.....................................................................................................7
IDENTIFYING EXTERNAL COMPONENTS .......................................9
FRONT PANEL ........................................................................................9
REAR PANEL ........................................................................................10
LED INDICATORS.................................................................................10
TECHNICAL SPECIFICATIONS .........................................................13

1
ABOUT THIS GUIDE
This user’s guide tells you how to install your 8-Port
1000BASE-T Gigabit Ethernet Switch, how to connect it to
your Gigabit Ethernet network.
Terms
For simplicity, this documentation uses the terms “Switch”
(first letter upper case) to refer to the 8-Port 1000BASE-T
Gigabit Ethernet Switch, and “switch” (first letter lower case) to
refer to all Ethernet switches, including the 8-Port 1000BASE-T
Gigabit Ethernet Switch.
Overview of this User’s Guide
Introduction. Describes the
Switch and its features.
Unpacking and Setup. Helps
you get started with the basic
installation of the Switch.
Identifying External
Components. Describes the
front panel, rear panel and
LED indicators of the Switch.
Technical Specifications. Lists
all the technical specifications
of the Switch.

3
INTRODUCTION
This section describes the features of the 8-Port 1000BASE-T
Gigabit Ethernet Switch, as well as providing some background
information about Gigabit Ethernet and switching technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet
utilizing the same packet structure, format, and support for
CSMA/CD protocol, full duplex, flow control, and management
objects, but with a tenfold increase in theoretical throughput
over 100-Mbps Fast Ethernet and a hundredfold increase over
10-Mbps Ethernet. Since it is compatible with all 10-Mbps and
100-Mbps Ethernet environments, Gigabit Ethernet provides a
straightforward upgrade without wasting a company’s existing
investment in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit
Ethernet is essential to coping with the network bottlenecks that
frequently develop as computers and their busses get faster and
more users use applications that generate more traffic.
Upgrading key components, such as your backbone and servers
to Gigabit Ethernet can greatly improve network response times
as well as significantly speed up the traffic between your
subnets.

4
Gigabit Ethernet supports video conferencing, complex imaging,
and similar data-intensive applications. Likewise, since data
transfers occur 10 times faster than Fast Ethernet, servers
outfitted with Gigabit Ethernet NIC’s are able to perform 10
times the number of operations in the same amount of time.
Switching Technology
Another key development pushing the limits of Ethernet
technology is in the field of switching technology. A switch
bridges Ethernet packets at the MAC address level of the
Ethernet protocol transmitting among connected Ethernet or fast
Ethernet LAN segments.
Switching is a cost-effective way of increasing the total
network capacity available to users on a local area network. A
switch increases capacity and decreases network loading by
making it possible for a local area network to be divided into
different segments which don’t compete with each other for
network transmission capacity, giving a decreased load on each.
The switch acts as a high-speed selective bridge between the
individual segments. Traffic that needs to go from one segment
to another is automatically forwarded by the switch, without
interfering with any other segments. This allows the total
network capacity to be multiplied, while still maintaining the
same network cabling and adapter cards.
Switching LAN technology is a marked improvement over the
previous generation of network bridges, which were

5
characterized by higher latencies. Routers have also been used
to segment local area networks, but the cost of a router and the
setup and maintenance required make routers relatively
impractical. Today’s switches are an ideal solution to most
kinds of local area network congestion problems.
Features
The 8-Port 1000BASE-T Gigabit Ethernet Switch was designed
for easy installation and high performance in an environment
where traffic on the network and the number of users increase
continuously.
8 1000BASE-T Gigabit Ethernet ports
Supports Auto-Negotiation for speed and duplex mode
Supports Auto-MDIX for each port
Support Full/Half duplex transfer mode for 10 and
100Mbps
Support Full duplex transfer mode for 1000Mbps
Full wire speed reception and transmission
Store-and-Forward switching method
Supports 4K absolute MAC addresses
Supports 128K Bytes RAM for data buffering
Extensive front-panel diagnostic LEDs
IEEE 802.3x flow control for full-duplex
Back pressure flow control for half-duplex

7
UNPACKING AND SETUP
This chapter provides unpacking and setup information for the
Switch.
Unpacking
Open the shipping carton of the Switch and carefully unpack its
contents. The carton should contain the following items:
One 8-Port 1000BASE-T Gigabit Ethernet Switch
Four rubber feet with adhesive backing
One external power adapter
This User’s Guide
If any item is found missing or damaged, please contact your
local reseller for replacement.
Setup
The setup of the Switch can be performed using the following
steps:
Install the Switch in a fairly cool and dry place. See
Technical Specification for the acceptable operation
temerature and humidity ranges.

8
Install the Switch in a site free from strong
electromagnetic source,vibration, dust,and direct sunlight.
Leave at least 10cm of space at the left and right hand
side of the Switch for ventilation.
Visually inspect the DC power jack and make sure that it
is fully secured to the power adapter.

9
IDENTIFYING EXTERNAL
COMPONENTS
This chapter describes the front panel, rear panel and LED
indicators of the Switch
Front Panel
The front panel of the Switch consists of eight 1000BASE-T
ports and LED indicators.
Front panel view of the Switch
1000BASE-T Ports:
Eight Gigabit Ethernet ports of 10/100/1000Mbps Auto-
Negotiation interface.
LED Indicators
Comprehensive LED indicators display the conditions of the
Switch and status of the network. A description of these LED
indicators follows (see LED Indicators).

10
Rear Panel
The rear panel of the Switch consists of an DC power connector.
The following figure shows the rear panel of the Switch.
Rear panel view of the Switch
DC Power Jack:
Power is supplied through an external AC power adapter.
Check the technical specification section for information about
the AC power input voltage.
LED Indicators
The LED indicators of the Switch include Power, Link/Act,
1000Mbps and 100Mbps. The following shows the LED
indicators for the Switch along with an explanation of each
indicator.

11
The Switch LED indicators
zPOWER
This indicator lights green when the Switch is receiving
power, otherwise, it is off.
zLink/ACT
These LED indicators are lighted up when there is a secure
connection (or link) to the desired port. The LED indicators
blinking whenever there is reception or transmission (i.e.
Activity—ACT) of data occurring at a port.
z1000Mbps
These LED indicators are lighted up when there is a secure
connection (or link) to 1000Mbps Gigabit Ethernet device at
the desired port.
z100Mbps
These LED indicators are lighted up when there is a secure
connection (or link) to 100Mbps Fast Ethernet device at the
desired port.
When the connection (or link) is 10Mbps, both of 1000Mbps
and 100Mbps LED indicators are off.

13
TECHNICAL
SPECIFICATIONS
General
Standards: IEEE 802.3ab 1000BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3 10BASE-T
IEEE 802.3x Flow Control
Protocol: CSMA/CD
Data
Transfer
Rate:
10Mbps (Half-duplex)Ethernet:
20Mbps (Full-duplex)
100Mbps (Half-duplex)Fast Ethernet:
200Mbps (Full-duplex)
Gigabit Ethernet: 2000Mbps (Full-duplex)
Topology: Star
Network
Cables:
Ethernet: 2-pair UTP Cat. 3,4,5 Unshield
Twisted Pair (UTP )Cable
Fast Ethernet: 2-pair UTP Cat. 5 Unshield Twisted
Pair (UTP )Cable
Gigabit Ethernet: 4-pair UTP Cat. 5 Unshield Twisted
Pair (UTP )Cable

14
General
Number of
Ports: Eight (8) 1000BASE-T Gigabit Ethernet ports
Physical and Environmental
DC inputs: 5V 2.4A
Power
Consumption: 10.5 watts maximum
Operating
Temperature: 0 °C ~ 40°C
Storage
Temperature: -10°C ~ 55°C
Humidity: 5% ~ 95% RH, non-condensing
Dimensions: 190(W) × 120(D) × 38(H) mm
Certification: FCC Class A, CE Marking Class A, VCCI
Class A
Performance
Transmission
Method: Store-and-forward
RAM Buffer: 128K Bytes per device
Filtering Address
Table: 4K MAC address per device
Packet
Filtering/Forwardi Full wire speed

15
Physical and Environmental
ng Rate:
MAC Address
Learning: Self-learning, auto-aging