trentios Y110RG-BP-S User manual

AIR CONDITIONER
REMOTE CONTROLLER MANUAL
Thank you very much for purchasing our air conditioner.
please read this owner s manual carefully before using
your air conditioner.
,

1
CONTENTS
Handling the remote controller 2
Remote controller specifications 3
Function buttons 4
Indicators on LCD 7
How to use the buttons 8
Auto operation 8
Cooling/Heating /Fan operation 8
Dehumidifying operation 9
Adjusting air flow direction 9
Timer operation 10
Follow Me function 13
Sleep function 14
Turbo function 14

2
Handling the remote controller
Replacing batteries
NOTE: When the batteries are removed, the remote controller erases all programming.
After inserting new batteries, the remote controller must be reprogrammed.
Location of the remote controller.
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
The air conditioner will not operate if curtains, doors or other materials
block the signals form the remote controller to the indoor unit.
8m
CAUTION
CAUTION
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not going to be
used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection of such waste
separately for special treatment is necessary.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
The remote controller is power by two dry batteries(R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(3) Reattach the cover by sliding it back into position.
(2) Remove the old batteries and insert the new batteries, placing the(+) and (-)
ends correctly.

3
Model Y110RG-BP-S
Buttons design might be slightly different from the actual one you purchased
depending on individual models.
According to the type of air conditioner (cooling only/cooling and heating type)
setting the application of remote controller:
After power on, the remote control displays "cooling" and "heating" alternatively
at intervals frequency of 1 Hz.
1.When display “cooling”, press any key( don’t transmit ), cooling only model has been
set and the display shows cooling control interface.
2.When display “heating”, press any key( don’t transmit ), heat pump model has been
set and the display shows cooling control interface.
Note:The remote control enters cooling and heating type automatically and shows
cooling control interface if no key be pressed within 10 seconds.
All the functions described are accomplished by the indoor unit.
if the indoor unit has no this feature, there is no corresponding operation
happened when press the relative button on the remote controller.
1. Operating Mode: AUTO, COOL, DRY, HEAT and FAN.
2. Timer Setting function in 24 hours.
4. Full function of LCD (Liquid Crystal Display).
3. Indoor Setting Temperature Range: 17 C~30 C.
Rated Voltage
Signal Receiving Range
Environment
3.0V(Dry batteries R03/LR03X2)
8m
-5 C~ 60 C
Remote Controller Specifications
Performance Feature
NOTE:
Select the cooling only or cooling and heating type of the remote

4
1
Operation starts when this button is pressed
and stops when this button is pressed again.
Function buttons ON/OFF Button
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction.
Press SWING button the horizontal louver
start swing, press the button again the
horizontal louver stop swing.
Note: Please do not select HEAT mode if the
machine you purchased is cooling only type.
Heat mode is not supported by the cooling
only appliance.
Note: While the unit is running under SLEEP
mode, it would be cancelled if press the MODE,
FAN SPEED or ON/OFF button.
AUTO
MODE Button
3
SWING Button
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
4
FOLLOW ME Button
Active/Disable SLEEP function.
Active/Disable FOLLOW ME function.
5
SLEEP Button
TURBO LED
LOCK RESET
ME
FOLLOW
18
9
11
10
12
13
14
15
2
3
4
5
6
7
COOL DRY HEAT FAN

5
Function buttons
Active/Disable TURBO function.
6
TURBO Button
When you press the recessed LOCK button,
all current setting are locked in and the remote
controller does not accept any operation
except that of the LOCK. Press again to
cancel the LOCK mode.
7
LOCK Button
ECO, abbr. of economical function, it is only
cool mode efficient.
In cool mode, press the ECO button start the
ECO function, press the button again stop
the function.
Note:
The machine will run under lower frequency if
you choose the ECO function, And the cooling
capacity should be relatively lower than that in
normal cooling mode.
Push this button to increase setting temperature
in the range of 17 C~30 C.
8
ECO Button
9
UP Button( )
Push this button to decrease setting temperature
in the range of 17 C~30 C.
10
DOWN Button( )
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
11
FAN SPEED Button
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
TURBO LED
LOCK RESET
ME
FOLLOW
18
9
11
10
12
13
14
15
2
3
4
5
6
7

6
Function buttons
Press this button to initiate the auto-on time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-on time to 0.0.
Active/Disable indoor screen Display.
12
TIMER ON Button
Press this button to initiate the auto-off time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timed setting
60 minutes increments. To cancel the
auto-timed program, simply adjust the
auto-off time to 0.0.
13
TIMER OFF Button
14
LED Button
When you press the recessed RESET button,
all current settings are cancelled and the
control will return to the initial settings.
15
RESET Button
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
TURBO LED
LOCK RESET
ME
FOLLOW
18
9
11
10
12
13
14
15
2
3
4
5
6
7

7
Indicators on LCD
This transmission indicator lighs when remote
controller transmits signals to the indoor unit.
Transmission Indicator
Displays the temperature setting(17 C~30 C).
When you set the operating mode to FAN, no
temperature setting is displayed. And if in the
TIMER mode, shows the ON and OFF setting
of the TIMER
Temp./Timer display
Displays the selected fan speed,AUTO(no
display) and three fan speed levels “ ”(Low)
“ ”(Med) “ ”(High) can be indicated.
Fan speed display
Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to remove.
ON/OFF display
Displayed when LOCK mode is activated.
Lock display
Displayed under eco operation,
Press the ECO button again to remove.
ECO display
Displayed under turbo operation,
Press the turbo button again to remove.
TURBO display
Displayed under sleep operation,
Press the sleep button again to remove.
SLEEP display
All indicators shown in the figure are for the purpose of clear presentation.
But during the actual operation only the relative functional signs are shown
on the dispaly window.
Note:
Display the current operation mode. Including
auto( ), cool( ), dry( ), heat( )(Not
applicable to cooling only models), fan( )
and back to auto( ).
Mode display

8
How to use the buttons
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the starts light.
1.Press the MODE button to select Auto.
2.Press the UP/DOWN button to set the
desired temperature. The set temperature
only reduces 2 C and only raises 2 C.
3.Press the ON/OFF button to start the air
conditioner.
1.Press the MODE button to select COOL,
HEAT(cooling & heating models only) or
FAN mode
2.Press the UP/DOWN button to set the
desired temperature. The temperature can
be set within a range of 17 C~30 C in 1 C
increments.
3.Press the FAN button to select the fan speed
in four steps-Auto,Low,Med,or High.
4.Press the ON/OFF button to start the air
conditioner.
Note:
1. In the Auto mode, the air conditioner can logically
choose the mode fo Cooling,Fan,and Heating
(not supported by the cooling only appliance.)
by sensing the difference between the actual
ambient room temperature and the setting
temperature on the remote controller.
2.In the Auto mode, you can not switch the fan speed.
It has already been auomatically controlled.
Note:
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not
able to control the room temperature either. In this
case, only step1, 3 and 4 may be performed.
AUTO operation
Ensure the unit is plugged in and power is
available.
Cooling/Heating/Fan operation
FOLLOW
ME
TURBO LED
LOCK RESET
3
2
1
2
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
FOLLOW
ME
TURBO LED
LOCK RESET
4
2
3
1
2

9
How to use the buttons
ECO
MODE
ON/OFF
SWING
SLEEP
FAN
SPEED
TIMER
ON
TIMER
OFF
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
display panel of the starts light.
1.Press the MODE button to select Dry mode.
2.The set temperature is in auto set,it can not
be changed. it has already been automatically
controlled lower 2 C than room temperature.
3.Press the ON/OFF button to start the air
conditioner.
Note:
In the Dry mode, you can not swithc the fan
speed. It has already been automatically
controlled.
Dehumidifying operation
Use the SWING and SWING button to adjust
the desired air flow direction.
When push the SWING button, the horizontal
louver will automatically swing up and down.
push the button again, the horizontal louver
will stop swing.
Adjusting air flow direction
TURBO LED
LOCK RESET
FOLLOW
ME
3
2
1
2