Triple S Cougar 17 User manual

TABLEOFCONTENTS
Safety Precautions 3
MachineOperation 4
Machine Maintenance & Storage 4
Handle Release Assembly Instructions 5
PartsList 6-9
Wiring Diagram 10
Warranty Policy 11

Safety Precautions
GROUNDING INSTRUCTIONS
General –This floor – finishing machine shall be
grounded while in use to protect the operator
from electric shock. The machine is provided
with a three –conductor cord and a three contact
grounding type attachment plug to fit the proper
grounding type receptacle. The green [or green
and yellow] conductor in the cord is the
grounding wire. Never connect this wire to other
than the grounding pin of the attachment plug.
This machine is for use on a nominal 120-Volt
circuit and has a grounding plug that resembles
the plug illustrated in figure below. Make sure
that the machine is connected to an outlet
having the same configuration as the plug. No
adapter should be used with this machine.
This machine is intended for Commercial use. It
is constructed for use in an indoor environment
and is not intended for any other use. Use only
recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1] Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand
operators manual.
-In flammable or explosive areas.
-With a damaged cord or plug.
-If not in proper operating condition.
-In outdoor areas.
-In standing water.
-With the use of extension cords.
2] Before operating machine:
-Make sure all safety devices are in place
and operate properly.
3] When using machine:
-Do not run machine over cord.
-Do not pull machine by cord or plug.
-Do not pull cord around sharp edges of
corners.
-Do not unplug by pulling on the cord.
-Do not stretch cord.
-Do not handle plug with wet hands.
-Keep cord away from heated surfaces.
-Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:
-Turn off machine.
-Unplug cord from outlet.
5] When servicing machine:
-Unplug cord from outlet.
-Use manufacturer supplied or approved
replacements parts.
-

Operation of Floor Machine
* Read operators manual thoroughly prior to
operating or servicing this machine.
GENERAL USE
1] Remove any obstructions or other
obstacles in the area which is to be cleaned.
2] Place the handle in the upright position and
tilt machine back until handle rests on the
floor.
lBe sure the machine is not plugged
into an outlet.
3] Attach the pad driver or brush to the machine
by placing the clutch plate over the gearbox
hub and turning the driver / brush 1/4 turn.
4] Place machine back into its upright position.
5] Plug power cord into grounded outlet.
* Never use an extension cord in
conjunction with the standard power cord.
6] The handle height may be adjusted by
lifting up the compression handle which is
located on the right side of the handle
tube about 1 foot above floor level.
Release the compression handle and
adjust handle to safe operating height,
then push back down on the compression
handle to lock the handle in operating
position.
7] To start the machine, press the red safety
button on the top of the upper switch
housing, and then squeeze either of the
operating triggers. [the safety button must
be depressed prior to squeezing the
operating triggers].
8] When the machine is in operation, both
hands should be placed on the switch
housing [upper handle].
9] During operation, to make the machine go
right, gently raise the handle. To make the
machine to left, gently lower the handle.
10] To stop the machine at any time, simply
release the operating trigger [s] and the machine
will stop automatically.
MAINTENANCE
To keep the machine performing well for many
years, please follow the following maintenance
procedures.
*Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1] Unplug machine as soon as you are done
using it.
2] Tilt machine back and remove pad driver or
brush.
*Never store a low speed machine with the
pad driver or brush mounted to the
machine
3] Clean the outside of the machine with a mild
cleaner.
4] Check power cord for any damage. If
damage is detected, replace the cord
immediately.
5] Lubricate wheels with a water resistant
lubricant once a month.
6] Check machine for loose or missing nuts and
bolts, and replace as necessary.
7] If the machine is used in a dusty environment,
you may remove the motor cover and blow
the motor clean with compressed air. This
will ensure proper ventilation, and allow the
motor to run cooler.
STORAGE
1] Unplug machine from power source and wrap
cord on handle.
2] Tilt machine back and remove pad driver or
brush.
3] Store machine in upright position and in a dry
area.

DIA
NO PART NUMBER NO REQ'D
1 VF30016 HANDLE RELEASE 1
2 VF30015 BOLT HANDLE RELEASE 1
3 VF30018 WASHER,PLAIN 2
4 VF13503 NUT, LOCK,M8X5.7 1
5 VF30017 SCREW 1
6 VF30014 COVER,HOOK 1
VF45125 CORD,HANDLE 1
AS41901 PLUG PROTECTOR,SMALL MALE 1
8 VF50120 GROMMET 1
9 VF13504 NUT,LOCK,M10 1
10 VF13517 WASHER,PLAIN 1
11 VF14114 SCREW,M8X55 1
12 VF30013 HOOK 1
13 VF13493 SCREW,M6X10 1
14 AS312206 TUBE 1
15 AS22002 SCREW,M5X16 1
16 AS312209 FRONT COVER 1
17 VF48310TR HANDLE GRIP 2
18 AS22006S LEVER,SOLUTION 1
19 AS22004S LEVER,LEFT,SWITCH 1
20 VV13661 SCREW,M4X12 2
21 VF48309 CLAMP BLOCK 1
22 VF45119U CORD,POWER SUPPLY 1
23 AS22009 STRAIN RELIEF,CORD 1
24 GT13009 SCREW,M5X30 5
25 GT13008 SCREW,M5X20 2
VF41194TR SERIAL TAG,17" 1
VF41004TR SERIAL TAG,20" 1
27 GV40218 SPRING,SAFETY BUTTON 1
28 GV40209 SAFETY BOTTON 1
29 AS312209 REAR COVER 1
30 VF99010C BREAKER, CIRCUIT, 17A / A-0701HS 1
31 VF44203 SWITCH ASSY 1
32 VF14212 SCREW,M3X25 2
33 AS22005S LEVER,RIGHT,SWITCH 1
34 AS312203 COVER 1
35 GV40226TR LABEL,FRONT COVER 1
36 VF13604 TEETH WASHER,M5 4
37 VF14222 SCREW,M5X12 4
38 VV13633 NUT,M5 2
39 AS22003 TEETH WASHER,M5 2
40 VF40200 VALVE ASSY KIT 1
41 VF40001 TANK SEAL KIT 1
42 VF40132 BARB HOSE 1
43 VF40139 HOSE,SOLUTION 1
44 VF40000 TANK MOUNTING KIT 1
45 MF-VF001 SOLUTION TANK 1
DESCRIPTOIN
HANDLE GROUP
7
26

DIA
NO PART NUMBER NO REQ'D
1GT13080 SCREW, M6 X 30 4
2AS312201TP PLATE,HANDLE GUIDE 1
3GT13030 WASHER, PLAIN, M6 4
4VF13502 4
5VF30026 AXLE 1
6VF30020 BRACKET, LEFT HANDLE 1
7VV20274 WASHER, PLAIN, M13 4
8GV40235 CLAMP BLOCK, AXLE 2
9VV13621 SCREW, SELF-TAPPING, ST, M5 X 20 4
10 VA13474 SCREW, M5 X 16 5
11 VF13474A WASHER, PLAIN, M5 4
12 VF13524 WASHER, PLAIN, M8 4
13 VF13519 WASHER, LOCK, M8 4
14 GT13016 SCREW, M8 X 55 4
15 MF-VF002-4A SCREW, SELF-TAPPING, 1/4"-1" 6
16 MF-VF002-2 CLUTCH PLATE 1
MF-VF021 PAD HOLDER, 16" 1
MF-VF022 PAD HOLDER, 19" 1
18 VF999802B GEAR BOX 1
19 VF99021 COUPLER 1
20 MT01102 SLEEVE 1
21 VF999821 BEARING,6002 LLU 1
22 VV13601 WASHER, LOCK, M5 6
23 VV13636 SCREW, M5 X 30 6
AS312101TR BUMPER, 17" 1
AS312204TR BUMPER, 20" 1
25 YLQ19200 ROTOR WITH FAN ASSY 1
26 YCQ10501 BEARING ,6203 RZ 1
27 YCQ12301 CENTRIFUGAL SWITCH 1
28 VV20509 SCREW, M5 X 10 2
VF40101TP FRAME,17" 1
VF40100TP FRAME,20" 1
30 YCQ12302 STATIONARY SWITCH 1
31 VF999854 RUN CAPACITOR, 50uF / 370V 1
32 VF40152 HOSE BARB 1
33 YLQ14601 MOUNTING FRAME (SMALL), CAPACITOR 1
34 VF30019 BRACKET, HANDLE, RIGHT 1
35 VF13520 WASHER, LOCK 2
36 VF50119 WASHER, PLAIN, M12 2
37 VF14214 SCREW, M5 X 8 4
38 VF48202 WHEEL, 5" 2
39 VF40994 LABEL, READ MANUAL 1
40 VF44012 SCREW, M6 X 12.7 2
41 VF13666 WASHER, M6 2
42 VF13604 WASHER, LOCK, EXTERNAL TOOTH 4
43 YCQ10615 MOUNTING FRAME (BIG), CAPACITOR 1
44 AS41902 PLUG PROTECTOR, LARGE FEMALE 1
45 YCQ10414 CLEAR COVER 4
46 YCQ10416 CAPACITOR WRAP 2
47 VF999805 START CAPACITOR (BIG), 400-450UF/150V 1
48 YLQ17507 BOLT ASSEMBLY 4
49 VF999787 MOTOR, 110V, 1.5HP 1
50 VF44003 LABEL, MOTOR 1
51 VF41079TR LOGO,TRIPLE 1
52 VF14222 SCREW, M5 X 12 3
53 VF30001TR TOP COVER,MOTOR 1
54 VF30002 CLUTCH PLATE 1
55 VF47023 BUMPER 1
DESCRIPTION
BASE ASSEMBLY
NUT, LOCK, M6
17
24
29

Warranty Policy
The warranty terms outlined below are in lieu of any other warranties, either stated or
implied, including any implied warranty of merchantability, fitness for a particular
purpose or otherwise. Under no circumstances will seller be liable for any loss,
damage, expense or consequential damages arising in connection with the use or
inability to use this product.
This warranty does not apply to damage or defect caused by accident, misuse,
negligence, abuse, fire or to any Triple S product which has been serviced by anyone
other than a Triple S authorized service representative. Housings or parts that have
become damaged as a result of improper use of the machine are excluded from this
warranty. Refer to owner’s manual for proper machine use and maintenance. Parts
that are expected to wear from normal use and, therefore are not covered under the
parts warranty include, but are not limited to: batteries (pro-rated for one year);
bearings; belts; brushes; filters; squeegees; switches; and tires.
This warranty commences on the date of purchase of the product by the original end
user from an authorized Triple S distributor, subject to proof of purchase. If proof of
purchase date is unavailable, the warranty begins 90 days after the sale of the
product to an authorized Triple S distributor.
•Subject to the conditions outlined above, the manufacturer warrants the
rotationally-molded polyethylene housings and parts on its machines to be
free from defects in materials and workmanship, under normal use and
service for twelve (12) years to the original purchaser.
•Under this warranty, the manufacturer guarantees the performance of
non-polyethylene parts and components on Triple S machines to be free
from defects for up to five (5) years to the original end user. Parts replaced
under this warranty are guaranteed for the remainder of the original
warranty period.
•Labor charges are covered for two (2) full years from the date of purchase
for Triple S products, provided an authorized Triple S service provider is
used for repair. No travel coverage is extended for cord electric machines.
Product Exceptions & Exclusions:. Battery chargers and all accessories are
warranted for one year.
Triple S reserves the right to change the warranty policy without notice.