Triple S PANTHER 15B User manual



OWNER’S MANUAL
IMPORTANT: READ OWNER’S MANUAL CAREFULLY

MODEL # PANTHER 15B MICRO SCRUBBER




FORYOURCONVENIENCE,RECORDTHEFOLLOWING
IMPORTANTINFORMATION
MODEL:___________________________________
SERIALNUMBER:____________________________
DATEPURCHASED:___________________________
PURCHASEDFROM:__________________________

Troubleshooting 12


TABLE OF CONTENTS
Safety Precautions 1
Machine Set Up & Installation 2-4
Machine Operation 4-5
Maintenance 5-6
Battery Charging 6
Preventative Maintenance 7
Parts Breakdown & Lists 8-10

Wiring Diagram 11
Warranty 13


Avoid moving parts. Do not wear loose
an cause explosion or fire. Do not pick up.
in tanks.
sparks and open flames away! Keep battery
Batteries emit hydrogen gas. Explosion or fi
not intended for any other use. Us l use. It is constructed for usThis machine is intended for commercia
SAFETY PRECAUTIONS
e in an indoor environment and is
e only with recommended accessories.
All operators shall read, understand and exercise the following safety precautions:
1) DO NOT OPERATE MACHINE:
Unless trained and authorized.
Unless you have read and understand the operators manual.
In flammable or explosive areas.
In outdoor areas.
2) BEFORE OPERATING MACHINE:
Make sure all safety devices are in place and operate properly.
3) WHEN USING MACHINE:
Go slow on inclines and slippery surfaces.
Follow all safety guidelines.
Be very careful when using the machine in reverse.
Report and fix any damage to machine prior to operating it.
4) BEFORE LEAVING OR SERVICING MACHINE:
Stop machine on level ground.
Turn machine off.
5) WHEN SERVICING MACHINE:
Read operators manual thoroughly prior to operating or servicing this machine.
Use manufacturer supplied or approved replacement parts.
Secure machine with wheel blocks prior to jacking the machine up.
Use approved jack or hoist to safely elevate the machine.
Disconnect batteries prior to working on machine.
Wear gloves when handling batteries or battery cables.
Avoid any contact with battery acid. fitting clothing while servicing machine.
WARNING！
WARNING！
WARNING！
1
re can result from hydrogen gas. Keep
compartment open when charging.
Flammable materials can cause an explosion or fire. Do not use flammable materials
Flammable materials or reactive metals c
If not in proper operating condition.

the squeegee up (33).
Be sure batteries are fully charged (see Battery Charging section).
if equipped if equipped
if equipped
d in figure 2. Pull up the lift lever (26) to raise
1. Turn off the machine.
Brush/Pad Driver Installation and Disassembly
Lower the squeegee (33) with the lift lever (26).
Pre-operation Checks
Charge the batteries (see battery charging section).
WARNING!
7. Brush or pad driver
6. Connecting wire for battery and charger
5. Electric Battery Charger Manual
2. Batteries (x2)
MACHINE SET UP & INSTALLATION
BATTERY DISASSEMBLY AND INSTALLATION
2
UNCRATING MACHINE
Be sure and check packing carton for any damage. Immediately report any damage to carrier.
Check contents of package to ensure that the following items are included:
1. Machine
3. Squeegee assembly
4. Scrubber-dryer User Manual （ ）
（ ）
1. Switch off the main switch (47).
2. Remove the recovery tank (2) as shown in the relevant paragraph.
3. Unscrew the bolt from batteries (16), then remove or change.
4. Install the batteries on the machine according to the diagram below.
5. Install the recovery tank.
Do not connect+ to +,or - to-,when disassembly or install the batteries. It is very dangerous.
 
Battery charging
MACHINE SET UP
1．Sweep or dust mop the surface to be cleaned.
2．Check that squeegee is properly installed.
3．
4．
5．Check that brush/pad is properly installed.
NOTE
2. Lay down the machine in this position as indicate
Only install manually. If auto-installation, it will wear brush hub.
Make sure that the tanks are empty before disassembling the brush.
Figure1
（ ）

Tighten the knobs securely (unscr
. The brush/pad could disengage and cause injury.
with a pipe or bucket. Do not remove the Solution F ilter (21) whileThe machine can be filled
Solution Tank F illing
(56/57), unscrew the thumb nut (37).
ew the knobs, if disassembling).
slide the squeegee into the slots of the squeegee
ion as indicated in figure 2.
down the squeegee on the “working” position.
Turn off the main switch (47).
Squeegee Installation
Do not turn on the machine in th position shown belowe
WARNING!
locks, as indicated in figure 3.
brackets.
3
3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it
1．
2．Pull down the squeegee lift lever (26) to put
3．Lay down the machine in this posit
4．Loosen the two knobs (55) on the squeegee and
5．To replace the front/rear squeegee
NOTE
Figure3
Figure2
hub.
4. To remove the brush/pad,rotate the brush/pad clockwise until it is released from drive wheel
filling.

When cleaning excessively aggressive floors this may cause the machine to not work.
ain cap (22) to let water pour out to a
cleaned after each scrubber operation is
and turn the latch (17) to lock the tank.Replace the recovery tank on the machine
he control panel (46).
means the machine is being overloaded.
T his
indicators on the control panel (46) will flash simultaneously.
rush motor and vacuumB
Before lifting the brush, turn it off by pressing the main switch (47).
Move the machine and start cleaning.
Pull one or both operating triggers (24), and then brush
turning the solution flow control lever (31) manually.
tion switch (50), the indicate light will be on.
Turn on the main switch (47). pulling down the squeegee lift lever (26).
Set the handle to a comfortable height by pressing handle rotate lever (25).
dirty water into a container, or unscrew the solution tank dr
Turn the latch (17) off the recovery tank, ta
Solution Tank D raining
Clean and rinse the recovery tank
bucket.
Open the lid (1) and overturn the recovery tank to drain the
Recovery Tank D raining
Screw on the solution tank drain cap (22).
the solution tank. The solution/water
will flow freely into a bucket or floor drain.
Unscrew the solution tank drain cap (22) on the bottom of
the inlet (20) through pipe or bucket.
build up and clogging of the solution lines.
intended for automatic scrubber applications.
4
Turn on the vacuum motor switch (49), the indicate light will be on.
1. Fill water into solution tank (3) from
2. Do not fill the solution tank completely, leave a few centimeters from the edge.
3. The water temperature must not exceed 40 .
NOTE
1．
2．Rinse the solution tank with clean water after every use. This will help prevent chemical
3．
NOTE
1．ke off the recovery tank from machine by
grasping two grooves of tank.
2．with clean water after every use.
3．
MACHINE OPERATION
1．
2．
3．
4．Turn on the brush motor switch (48) and the solu
5．
6．If necessary, adjust the water flow by
7．
NOTE
.
CAUTION！
CAUTION！
Solution tank should be drained and
completed.
Recovery tank should be drained and cleaned after each scrubber operation is
completed.
If the battery indicator light (51) is green, the machine can be used. If it is yellow or red, the
batteries must be charged.
CAUTION！
Use only low-foam and non-flammable detergents,
Lower the squeegee (33) onto the floor by
will start to spin, solution will begin to flow.
Please turn offall the switches on t

℃

This manual describes the easiest
1. Perform the procedures shown above in
earlyY
Months
Every Six
Weekly
the machine)
Daily, (after using
Table, refer to the
Service
and most common maintenance
procedures.
arefully read the instruction in the Safety precaution section.charger cable disconnected. C
WARNING!
(After Using the Machine section).
DO NOT USE MACHINE FOR A LONG TIME
than 30 days, please procee
warranty.
machine prior to storage. Any damage caused by fr
with the brush/pad holder and the squeegee.
tenance section).
1. Remove the brush/pad holder.
2. Empty the tanks as shown in the previous paragraph.
5
CAUTION！
Do not use the machine with discharged batteries to avoid damaging the batteries and reducing the battery
life.
AFTER USING THE MACHINE
After scrubbing, please proceed with below actions before leaving the machine:
3. Perform the daily maintenance procedures (see the main
4. Store the machine in a clean and dry place,
5. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the
eezing temperatures will not be covered by the
If the machine is not going to be used for more d with below actions:
2. Disconnect the battery connector.
MAINTENANCE
The lifespan of the machine and its maximum operating safety are ensured by correct and regular
maintenance. The following chart provides the scheduled maintenance. The intervals shown may
vary according to particular working conditions, which will be defined by the person in charge of the
maintenance.
Maintenance procedures must be performed with the machine switched off and the batteries/battery
All scheduled or extraordinary maintenance procedures must be performed by qualified personnel, or
by an authorized Service Center.
For other maintenance procedures shown in the Scheduled Maintenance
Manual that can be consulted at any Service Center.
SCHEDULED MAINTENANCE TABLE
Procedure
Battery charging
Squeegee cleaning
Brush cleaning
Tank and vacuum grid with float cleaning, the
cover gasket check
Squeegee blade check and replacement
Solution filter cleaning

it' s charging, green light means battery charging
5. The charging indicator light (30) turns on when
rotary parts lubricated
(2). Exposing battery compartment.
as there may be battery fluid leaks. The battery
1
Keeping the batteries charged makes battery life last longer.
relevant section.
Please use appropriate charger to charge the battery.
Charge the batteries when the yellow or red indicator (51),or at the end of every working cycle
by an authorized Service Center.
After the first 8 working hours.
Brush/Pad holder motor carbon brush check or
machine socket. Connect the charging cable to the
he grounded wall outlet (100v~240v).
6. Upon the completion of charging, first unplug
7.
6
or eyes, rinse thoroughly with water and consult a
Out-water pipe filter cleaning
Screw and nut tightening check （1）
（1）
replacement （2）
Vacuum system motor carbon brush check or
replacement （2）
This maintenance procedure must be performed
BATTERY CHARGING
NOTE
CAUTION！
CAUTION！！
If the machine is not equipped with on-board battery charger, choose an external battery charger
suitable for the type of batteries installed.
WARNING！
WARNING！
Pay careful attention when charging WET batteries
fluid is corrosive. If it comes in contact with skin
physician.
1. Place charger and machine in a well ventilated area.
2. Turn machine off (47).
3. Take away the recovery tank
4. Plug the charging cable to t
is completed. the charging cable from the wall outlet and then
disconnect from machine.
Replace the recovery tank .
NOTE
For further information about the operation of the battery charger (29), see the
.
（ ） 

（ 2 ）


4. Take off all vacuum kits, gasket, filter, clean and re-install.
(37) to remove the blades.
the vacuum rubber connector (18) between two tanks
as shown in Machine set up section.
BRUSH/PAD DRIVER CLEANING
s. Replace if necessary.
3. Unscrew the thumb nut
are integrity or not.
7
SQUEEGEE CLEANING
NOTE
CAUTION !
It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.
SQUEEGEE BLADE CHECK AND REPLACEMENT
1. Take off the squeegee as shown in the previous paragraph.
5. Install the squeegee in the reverse order of removal.
CAUTION！
It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris.
2. Clean and wash the brush/pad with water and detergent.
3. Check the brush bristles for integrity and wearing status; if necessary, replace the brush.
4. Check the pad for wearing status; if necessary, replace the pad driver.
TANK/VACUUM GRID WITH FLOAT CLEANING AND COVER GASKET
CAUTION！
It is advisable to wear protective gloves when cleaning the tank and vacuum/suction assembly because there
may be sharp debris.
1. Move the machine to the appointed disposal area.
2. Turn off the main switch (47).
3. Take off the recovery tank (2), clean and rinse both solution/recovery tank, and drain out.
5. Check the recovery tank lids gasket ring and
NOTE
The gasket ring of recovery tank and the rubber connector between two tanks create
vacuum in the tank. If necessary, replace them. .
a good drying performance.
The squeegee must be clean and its blades must be in good condition in order to getting
are cracked or split, if necessary replace them with new.2. Check to see if the edge of the front/rear blades
4. Check the front/rear blades for integrity, cut and tear
1. Remove the brush/pad

Screw nut
Squeegee adjustment piece
Rear squeegee
Front squeegee
Knob
59.
58.
57.
56.
55.
29. Battery Charger
PARTS LIST
35. Squeegee hose
34. Squeegee wheels
8
1. Recovery tank lid
2. Recovery tank
3. Solution tank
5. Protective rollers
6. Brush
7. Front handle shell
8. Control panel
9. Rear handle shell
10. Handle rubber
11. Handle iron pipe
12. Squeegee vacuum assembly
13. Squeegee suction assembly
14. Left positioning
15. Right positioning
16. Batteries
17. Latch
18. Rubber sealing
19. Limit hose joint
20. Inlet
21. Solution filter
22. Solution tank drain
23. Wheels on fixed axle
24. Handle left and right
25. Handle rotate lever
26. Squeegee lift lever
27. Squeegee string
28. Box circuit
30. Battery charge indicator
31. Solution flow control lever
32. Electromagnetic valve data
33. Squeegee
36. Axle
37. Thumb nut
38. Vacuum system motor
39. Brush motor
40. Drive belt
41. Belt
42. Squeegee rotation plate
43. Squeegee lift plate
44. Squeegee fixing plate
45. Motor fixing plate
cover4. Brush
54
53
52
51
Vacuummotorswitch
Brushmotorswitch
Mainswitch
Control panel
46．
Electric quantity indicator
47．
Brush motor indicator
48．
Vacuum motor indicator
49．
Suction Electromagnetic valve data indicator
50．Suction Electromagnetic valve data switch
．
．
．
．

PARTS BREAKDOWN
9
32
31 33
37 56
57
30
29
28
27
26
24
25 41
42
45
44
43
40
3938
8
2322
20
21
1819
9
16
17
15
14
13
12
11
10
3
4
7
6
5
2
1
36
22
35
34
59
58
33

Sound level 68dBA
Machine length x width x height 770x500x550MM
Control Panel
Vacuum motor data 24V 300W
Input 100-240
Carton spec 780x415x590MM
10
54
53
52
51
Vacuummotorswitch
Brushmotorswitch
Mainswitch
Control panel

46．Electric quantity indicator
47．Brush motor indicator
48．Vacuum motor indicator
49．Suction Electromagnetic valve data indicator
50．Suction Electromagnetic valve data switch
TECHINICAL DATA
Solution tank capacity 15L
Recovery tank capacity 15L
Wheel diameter 254MM
Brush motor data 24V 250W
Electromagnetic valve data 24V
Maximum gradient 2%
Batteries data （2×12V）24V 33Ah/20h
Power cable length /
Batteries spec 196 x 130 x 175mm
Working capacity, up to 800mm
Cleaning productivity 750m2/hour
Squeegee width 490mm
Brush diameter 380mm
Brush rpm 150rpm
Charger Vac,50-60HZ
Output 24Vdc,5A
Machine weight 60kg
Machine weight(with charger and
package) 65kg
．
．
．
．

WIRING DIAGRAM
11

CONTROL BOARD
KEY-PRESS BOARD
WV PTC
VACUUM PTC
CB PTC
PRUSH PTC
12AWG RED
12AWG BLACK
2# 14AWG RED
2# 14AWG BLACK
1# 14AWG RED
1# 14AWG BLACK
LINKE C3.2
LINKE C3.1
J2
J3
J7.1
J7.2
18AWG RED
18AWG BLACK
20AWG WHITE
16AWG BLACK
20AWG WHITE
16AWG RED
SAFETY SWITCH
VCC
J5
J4
J11.2
J10.7 J10.6 J10.5 J10.4 J10.3 J10.2 J10.1
J11.1
J8.3
J9.7 J9.6 J9.5 J9.4 J9.3 J9.2 J9.1
WATER VALVE VACUUM MOTOR BRUSH MOTOR
M
M
LINKE C2.2
LINKE C2.1
WV
GND
12AWG BLACK
J8.1
COMMUNICATION LINE
LINKE C1.2
LINKE C1.1
12AWG RED
CHARGER
-+
-+
12V STORAGE BATTERY
12V STORAGE BATTERY
12AWG BLACK

The recovery tank is not locked Lock the latch (17)
12
light (51) turns red
light (51) does not turn on
indicator light (52) does not turn on
Solution flow control valve (31) is blocked up Clean the valve
The squeegee leaves marks on the floor
The solution flow is insufficient
The recovery tank is full Empty the recovery tank
threads,etc) preventing the brush from
There are foreign materials (tangled
vacuum motor indicator light (53) does
not turn on
the appropriate position
ust the screw nut(59 )to
Adj
ustment piece(58 )not set at an
appropriate position
j
Squeegee ad

TROUBLESHOOTING
The solution is dirty Empty the solution,clean
clean solution.
the tank and refill with
The solution is empty Fill the tank
Connect
The power line disconnected from the power Connect
The PCB or key board is faulty Change the PCB or key
The PCB or key board is faulty Change the PCB or key
The suction power is insufficient
Vacuum system motor does not work,
Vacuum system motor does not work,
indicator lights (52) flash
Brush motor does not work, brush
Brush motor does not work, brush
The machine does not work, indicator
The machine does not work, indicator
brush indicator lights (53) flash
Trouble Possible Cause Remedy
The battery connector is disconnected Connect
The batteries are completely discharged Charge the batteries
The batteries are discharged Charge the batteries
board
The deck motor is overloaded Use less aggressive
brushes suitable for the
floor to be cleaned
rotating
Clean the brush hub
board
The vacuum system motor is overloaded Check the vacuum system
motor
The hose is disconnected from the
squeegee
Vacuum assembly is clogged Clean or check
The squeegee is dirty, or the squeegee
blades are worn or damaged
Clean and check the
squeegee
The tank cover is not properly closed, or the
gasket is damaged
Close the cover properly
or replace the gasket
There is debris under the squeegee blades Remove the debris
The squeegee blades are worn, chipped or
torn
Replace the blades

WARRANTY POLICY
The warranty terms outlined below are in lieu of any other warranties, either stated or implied,
including any implied warranty of merchantability, fitness for a particular purpose or otherwise.
Under no circumstances will seller be liable for any loss, damage, expense or consequential
damages arising in connection with the use or inability to use this product.
This warranty does not apply to damage or defect caused by accident, misuse, negligence, abuse,
fire or to any Triple S product which has been serviced by anyone other than a Triple S authorized
service representative. Housings or parts that have become damaged as a result of improper use
of the machine are excluded from this warranty. Refer to owner’s manual for proper machine use
and maintenance. Parts that are expected to wear from normal use and, therefore are not
covered under the parts warranty include, but are not limited to: batteries (pro-rated for one year);
bearings; belts; brushes; filters; squeegees; switches; and tires.
This warranty commences on the date of purchase of the product by the original end user from an
authorized Triple S distributor, subject to proof of purchase. If proof of purchase date is
unavailable, the warranty begins 90 days after the sale of the product to an authorized Triple S
distributor.
Subject to the conditions outlined above, the manufacturer warrants the
rotationally-molded polyethylene housings and parts on its machines to be free from
defects in materials and workmanship, under normal use and service for twelve (12)
years to the original purchaser.
Under this warranty, the manufacturer guarantees the performance of non-polyethylene
parts and components on Triple S machines to be free from defects for up to five (5)
years to the original end user. Parts replaced under this warranty are guaranteed for the
remainder of the original warranty period.
Labor charges are covered for five (5) full years from the date of purchase for Triple S
products, provided an authorized Triple S service provider is used for repair. No travel
coverage is extended for cord electric machines.
Product Exceptions & Exclusions: Battery chargers and all accessories are warranted for one
year.
Triple S reserves the right to change the warranty policy without notice.