Triple S JAGUAR 20R User manual

MODEL:
1/2017VR28023
86014
FOR YOUR CONVENIENCE, RECORD THE FOLLOWING
IMPORTANT INFORMATION
MODEL:__________________________________________
SERIAL NUMBER: _________________________________
DATE PURCHASED:________________________________
PURCHASED FROM: _______________________________
JAGUAR 20R

.........
13
13
14-15
14
14
16
15
16
16
17
18
18
18-20
20
............................21-56
.....
.......................................................................................................................................................... 9
8-9
8
8
................................. 7
.............................
BATTERY INSTALLATION AND BATTERY TYPE-SETTING (WET OR GEL/AGM)
TROUBLE-SHOOTING
PARTS BREAKDOWN + LISTS ......................................
..............
.......................
.................10-11
9-10
......... 2-3
SYMBOLS THAT APPEAR ON THE INSTRUCTION FOR USE MANUAL
SAFETY
TABLE OF CONTENTS
INTRODUCTION............................................................................................................................ 1
MANUAL CONTENT AND PURPOSE ....................................................................................................................................... 1
HOW TO KEEP THIS MANUAL ................................................................................................................................................ 1
ACCESSORIES AND MAINTENANCE ........................................................................................................................................ 1
CHANGES AND IMPROVEMENTS ........................................................................................................................................... 1
SCOPE OF APPLICATION ......................................................................................................................................................... 1
MACHINE IDENTIFICATION DATA .......................................................................................................................................... 1
TRANSPORT AND UNPACKING ............................................................................................................................................... 1
............................................................................................................................ 2
...................................................................................... 2
GENERAL SAFETY INSTRUCTION ................................................................................................................................
MACHINE DESCRIPTION................................................................................................................ 4
MACHINE STRUCTURE ........................................................................................................................................................... 4
CONTROL PANEL .................................................................................................................................................................... 5
LED SCREEN DISPLAY INFORMATION ..................................................................................................................................... 5
DISPLAY WINDOW OF CHARGER INDICATON LIGHT ............................................................................................................. 5
TECHNICAL PARAMETERS ...................................................................................................................................................... 6
CIRCUIT DIAGRAM ................................................................................................................................
OPERATING GUIDE .......................................................................................................................
INSTALLING AND SETTING OF NEW MACHINE BATTERY .......................................................................................................
................................................................
EMERGENCY BRAKING
BRUSH/PAD INSTALLATION AND UNINSTALLATION ................................................................................................
ADJUSTING THE BALANCE OF SQUEEGEE ............................................................................................................................ 10
SOLUTION TANK FILLING ................................................................................................................................
MACHINE START AND STOP ................................................................................................................................................. 11
MACHINE OPERATION (SCRUBBING AND DRYING) ............................................................................................................. 12
TANK EMPTYING .................................................................................................................................................................. 13
AFTER USING THE MACHINE ................................................................................................................................................
MACHINE LONG INACTIVITY ................................................................................................................................................
USING FOR THE FIRST TIME .................................................................................................................................................
MAINTENANCE ...........................................................................................................................
SCHEDULED MAINTENANCE TABLE .....................................................................................................................................
BATTERY CHARGING ................................................................................................................................
BRUSH/PAD CLEANING ........................................................................................................................................................
SOLUTION FILTER CLEANING ...............................................................................................................................................
SQUEEGEE CLEANING ..........................................................................................................................................................
SQUEEGEE BLADE CHECK AND REPLACEMENT ....................................................................................................................
TANK AND VACUUM GRID WITH FLOAT CLEANING, AND COVER GASKET CHECK ..............................................................
FUSE CHECK/REPLACEMENT ................................................................................................................................................
ACCESSORIES/OPTIONS .......................................................................................................................................................
................................................................................................
SCRAPPING ................................................................................................................................
................................
14

Your local Distributor
, or by
operation, storage,
maintenance, spare parts and how to scrap it.
needed.
ments without notice.
We are committed to
your local Distributors appointed service center. ONLY authorized spare parts and accessories should be used.
Contact your local distriubutors customer service for any service or purchase of accessories or spare parts if necessary.
products, and reserve the right to machine changes
The manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can
will
not be answerable for damages coming from the non
an authorizedmanual carefully. Contact
Manual is to provide the operator with necessary information to use
the machine properly
Instruction for Owner's
1
INTRODUCTION
NOTE
The numbers in brackets refer to the components shown in Machine Description chapter.
MANUAL CONTENT AND PURPOSE
The purpose of this
and safely. It contains information about technical data, safety,
Before performing any procedure on the machine, no matter the operators and qualified technicians must read this
’service center for any query about this manual or for any further information
The operators must not perform procedures that should be done by qualified technicians.
- observance of this prohibition.
HOW TO KEEP THIS MANUAL
cause any damage to it.
ACCESSORIES AND MAINTENANCE
All the necessary operation, maintenance and repair procedures must be performed by qualified personnel
CHANGES AND IMPROVEMENTS
continuous improvement of the
and improve
SCOPE OF APPLICATION
The scrubber applies to commercial and industrial use. It is suitable for cleaning smooth and solid floors, operating by a
qualified personnel in safety circumstance. It is not suitable for outdoor use, carpet or rough floor cleaning.
MACHINE IDENTIFICATION DATA
The machine serial number and model name are marked on the serial label.
This information is useful. Use the following table to write down the machine identification data when requiring spare
parts for the machine.
MACHINE MODEL....................................................................................
MACHINE SERIAL NUMBER......................................................................
TRANSPORT AND UNPACKING
When the carrier delivers the machine, make sure the packaging and machine are both whole and undamaged. If any
damaged, make the carrier know the damage and before accepting the goods, reserve the right in compensation of the
damage.
Follow the instructions on packing strictly when unpacking the machine.
Check the package to ensure following items are included:

Owner's Manual before
Owner's Manual
ot operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or vapor
which may cause explosion
INSTRUCTION FOR USE MANUAL
2
1. Technical documentations including , and on-board charger manual if on-board charger is equipped.
2. Charger cable if on-board charger is equipped.
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all
necessary precautions to safeguard people and property.
SYMBOLS THAT APPEAR ON THE
DANGER!
It indicates a dangerous situation with risk of death for the operator.
WARNING!
It indicates a potential risk of injury for people.
CAUTION!
It indicates a caution or a remark related to important or useful functions.
Pay attention to the paragraphs marked by this symbol.
NOTE
It indicates a remark related to important or useful functions.
CONSULTATION
It indicates the necessity to refer to the Instruction for performing
GENERAL SAFETY INSTRUCTION
Specific warnings and cautions to inform about potential damages to people and machine are shown below.
DANGER!
 This machine must be operated by trained and authorized personnel according to guidance of the manual.
 Before performing any cleaning, maintenance, repair or replacement procedure, read all the instructions
carefully, ensure to turn the machine OFF and disconnect the battery connector.
 Do n .
This machine is not suitable for collecting dangerous powders.
 Do not wear jewels when working near electrical components.
 Do not work under the lifted machine without supporting it with safety stands.
 When using lead (WET) batteries, they may emit inflammable gas under normal use, must keep sparks,
flames, smoking materials and radiating, illuminating and burning items away from the batteries.
 When charging lead (WET) batteries, they may emit hydrogen gas . Must ensure
the charging environment is well ventilated and away from naked flames.
WARNING!
 Check the machine carefully before each use. Ensure that all the components have been well assembled
before use. Or it may causes damages to people and properties.
any procedure.

spare parts need to be replaced, order
g tool only, not for any other purpose .
Use the machine only where proper lighting is pr
Use machine as a cleanin
ed Distributor.ORIGINAL spare parts from an authori
serious damage
3
 Before using the battery charger, ensure that the values of frequency and voltage indicated on the machine
serial number label match those of mains.
 Never move the machine by pulling the battery charger cable. Do not let the cable through a closed door, or
winding on sharp edges or corners. Do not run the machine on the battery charger cable. Keep the battery
charger cable away from heated surfaces.
Do not charge the batteries if the battery charger cable or the plug are damaged.
 To reduce the risk of fire, electric shock, or injury, make sure machine is off before leaving.
 Use or store the machine indoors in dry conditions, it is not allowed for outdoor use.
 The machine both storage and working temperature must be between 0 °C and +40 °C, the humidity of air
must be between 30% - 95%.
 Do not use the machine on slopes with a gradient exceeding as specification show.
 When using and handling floor cleaning detergents, follow the instructions on the labels of the detergent
bottles and wear suitable gloves and protections.
 Use brushes and pads supplied with the machine or defined in the manual. Using other brushes or pads
could reduce safety.
 In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary, request
assistance from the authorized personnel or from an authorized Service Center.
 Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the machine
moving parts.
 Do not use the machine in particularly dusty areas.
Do not wash the machine with direct or pressured water jets, or with corrosive substances.
 Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
 Do not lean liquid containers on the machine, use the relevant can holder.
 To avoid damaging the floor, do not allow the brush/pad to operate while the machine is stationary.
 In case of fire, use a dry powder fire extinguisher. Do not use liquid fire extinguishers.
 Do not remove or modify the machine stickers.
 Do not tamper with the machine safety guards and follow the ordinary maintenance instructions
scrupulously.
 Pay attention during machine transportation when temperature is below freezing point. The water in the
recovery tank and in the hoses could freeze and cause to the machine.
 If z
 Return the machine to the Service Center if it doesn’t work as usual or it is in condition such as damaged,
placed outdoors, dropped into water.
 To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of
this Manual, must be performed by the authorized personnel or an authorized Service Center.
 The machine must be properly disposed of, because the presence of toxic-harmful materials (batteries, etc.),
which are subject to standards that require disposal in special centers (see Scrapping chapter).

 Always keep the openings free from dust, hairs and any other foreign material which could reduce the
airflow. Do not use the machine if the openings are clogged.
 ovided.
 This machine is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the
machine by a person responsible for their safety.
 Close attention is necessary when used near children.
 Children should be supervised to ensure that they do not play with the machine.
 While using this machine, take care not to cause damage to people or objects.

4
MACHINE DESCRIPTION
MACHINE STRUCTURE (as shown in Figure 1)
1. Steering wheel
2. Seat cushion
3. Recovery tank
4. Recovery tank cover
5. USB charging port
6. Pedal
7. Front wheel
8. Left support bracket
9. Solution Filter
10. Brush
11. Brush deck
12. Rear wheel
13. Squeegee assembly
14. Solution outlet cover
15. Sewage drain hose
16. Water inlet cover
17. Solution tank
18. Squeegee adjustment knob
19. Vacuum hose
20. Squeegee knob
21. Control panel
22. Emergency switch
23. Squeegee lifting/lowering lever
24. Accelerate pedal
25. Front bumper
26. Solution level indicator
27. Right support bracket
28. Battery
29. Drive motor
30. Brake block bracket
31. Squeegee hasp
12 3 4
5
6
78910 11 12 13 14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
31
20
Figure 1

12.3 hours
5
MACHINE DESCRIPTION
CONTROL PANEL (as shown in Figure 2)
31. LED screen
32. Discharged battery warning light (Red)
33. Battery semi-discharged indicator (Yellow)
34. Horn button
35. Solution volume adjusting button
36. Forward-Backward switch
37. Battery fully charged indicator (Green)
38. Solution tank empty indicator
39. Brush button
40. Key switch
41. Brush unload button
42. Drive motor trouble light
43. Speed adjusting knob
44. Vacuum motor overload protector
45. Drive motor overload protector
46. Brush motor overload protector
47. Battery charge indicator (Red)
48. Battery semi-charged indicator (Yellow)
49. Battery fully charged indicator (Green)
50. Charger plug cover
51. Charger plug
LED SCREEN DISPLAY INFORMATION
STOP –Machine cannot move, brush stops working but vacuum motor can work
(00012.3) –Total working hours of machine are
L0-(18) –Battery voltage lower than 18V
U-(25.5) –Battery voltage is 25.5V
ERR-01 –Squeegee is not lifted when machine turns backward
DISPLAY WINDOW OF CHARGER INDICATON LIGHT (as shown in Figure 2)
1. At the beginning of charging, the Yellow LED (48) twinkles, the red LED (47) and green LED (49) turn on for a second,
on the red LED turns off, and then the green LED twinkles a few times before the red LED on charger is normally. It
is the first stage of charging.
2. After charging for some time, the red LED (47) on charger turns off, the yellow LED (48) turns on, this is the second
stage of charging.
3. When charging is completed, the yellow LED (48) turns off, the green LED (49) turns on to indicate that the battery
is fully charged.
NOTE
In the process of charging, if the yellow light (48) is on, it may be caused by: Battery and charger doesn’t
match, battery is not connected well, or output is short-circuited.
The red light of charger flashing may be caused by the charger internal short circuit.
42
31
32
35
36
38
39
40
41
43
37
33
44
45 47
48
34 50
46
49
51
Figure 2

g dimensions (L x W x H)
300 mm 13.8 x 15 x 11.8 inch
24 V 10 A24 V 10 A
530 mm
530 mm
450 Watt
160 Rpm
23 Kg
Watt
24 V
x
V, 0.8 5 V, 0.8 A
24 V
0.4 HP
50.7 lbs
160 Rpm
0.6 HP
20.9 inch
20.9 inch
0.53 gal/min2.0 L/min 0.22
9.1 inch
6.9 inch
0.54 HP
19.3 gal
19 gal
1310 mm 57.9 x 28.7 x 51.6 inchx
270
540.6 lbs
595.8 lbs
308.9
22.8 inch
53.5 inch
Kg
580 mm
1360 mm
1120 mm 44.1 inch
3.42 miles/h
x
x
Jaguar 20R
6
TECHNICAL PARAMETERS
MODEL
Packin1470 730
Machine height
Machine length
Machinewidth (without squeegee)
Machine weight with empty tanks
(without batteries)
140 lbs
Gross vehicle weight (GVW) Kg
Shippingweight 245 Kg
Solution tank capacity 72 Liter
Recovery tank capacity 73 Liter
Vacuum motor power 400 Watt
Vacuum capacity 1223 mm H₂O 48 inch H₂O
Climbing capacity (Max) 10% 10%
Front wheel diameter 175 mm
Rear wheel diameter 230 mm
Sound level 69 dB(A) 69 dB(A)
Solution/water Flow 0.84- -
Working width
Squeegee width 7
30
mm 28.7 inch
Brush/pad diameter
Brush motor power
Brushspeed
Brush/pad pressure (Max)
Drive motor power 300
Working speed 5.5 km/h
Voltage
Battery2x10 AH (20 hours) 2x10 AH (20 hours)
Battery charger
Battery compartment size (L x W x H) 350 380
USB charger specification 5 A

7
CIRCUIT DIAGRAM

8
BATTERY TYPE-SETTING
for use.
light (33) flashes, machine is se
If the red light (32) flashes, machine is set up to use WET batteries.
f the green light (37) flashes, machine is set up to use GEL/AGM batteries.
Follow steps below to change the machine settings.
hen installing new batteries, follow Figure
RNING
Figure 3
OPERATING GUIDE
WARNING!
Pay high attention to these symbols in this manual:
–DANGER!
–WA !
–CAUTION!
–CONSULTATION
Never cover these symbols on the machine for any reason, replace it immediately if any damage.
INSTALLING AND SETTING OF NEW MACHINE BATTERY
WARNING!
The electric components of the machine can be seriously damaged if the batteries are either improperly
installed or connected.
The batteries must be installed by qualified personnel. Set the battery charger (optional) and machine PCBA
according to the battery type (WET or GEL/AGM).
Check the batteries whether it is damaged before installation.
Disconnect the battery connector and the battery charger plug.
Handle the batteries with great care.
NOTE
The machine requires two 12V batteries, connecting according
to Figure 3.
The machine can be operated in one of following battery modes:
A) WET or GEL/AGM batteries are already installed and ready to
be used
1. Check the batteries and connect the battery connector to the machine.
2. Insert the key switch (40) and turn to “on”. If the green light (48) turns on, batteries are full charged If the
yellow or red light (47 or 48) turns it on, the batteries must be charged.
B) Without Batteries
1. If your machine isn’t equipped with batteries, buy appropriate batteries [See the Technical Data Paragraph]. For
battery choice and installation, turn to qualified battery Retailers.
2. When batteries are ready, set the machine and the battery charger according to the type of installed batteries,
then follow the procedures shown in the next paragraph.
BATTERY INSTALLATION AND (WET OR GEL/AGM)
Set the electronic circuit board of the machine and battery charger according to battery types (WET or GEL/AGM)
following steps below:
NOTE
W 4 to set DIP switch, or batteries may be damaged by wrong
setting.
Machine setting
1. Insert key switch (40) and turn to “ON”, pay attention to below during the first seconds of machine start:
 I
 If the yellow t up to use Discover EV AGM batteries.

2.
3. The factory setting of the machine is to use Discover EV AGM batteries. If the setting corresponds to selected
batteries, go to step 6 directly, or follow the next step.

The machine is supplied with cables suitable to install two 12V
pad, make sure all of the switches on machine are
5).
(NOTE: Turn pin 1 and pin 2 of DIP switch
pin 2 to “OFF”)
(NOTE: Turn pin 1 and pin 2
9
A
B
Figure 5
A
C
B
Figure 6
4. Unscrew the screw (B, Figure 4) on control panel, then turn over the PCBA (A) on the panel to find DIP switch (D),
follow Figure 4 for DIP settings.
5. Perform steps in reserve order of disassembly to fix control panel and lock the screw after setting is done.
1
WET BATTERIES
of DIP switch
to “OFF”)
2
DISCOVER EV AGM BATTERIES
(NOTE: Turn pin 1 of DIP switch to “ON”,
3
GENERAL GEL/AFM BATTERIES
to “ON”)
Battery Installation
6. Open the recovery tank cover (4) and check the recovery tank (3) is empty, otherwise, empty it with the drain hose
(15).
7. Close the recovery tank cover (4).
8. Overturn the recovery tank (3) carefully.
9.
batteries. Carefully put the batteries into the compartment,
then install them correctly.
10. Route and install the battery cable as shown in (Figure 3),
then carefully tighten the nut on each battery terminal.
11. Place the protection cap on each terminal, then connect the
battery connector.
12. Carefully lower the recovery tank (3).
Charging the Batteries
13. Charging the batteries. [Refer to MAINTENANCE chapters].
EMERGENCY BRAKING
If there is any emergency during machine operating, press the emergency switch (A, Figure 5), then all functions of
machine will stop, there is no display on control panel (B, Figure
BRUSH/PAD INSTALLATION AND UNINSTALLATION
NOTE
Install suitable brush (A, Figure 6) or Pad (B and
C, Figure 6) according to the type of floor to be
cleaned.
CAUTION
Before installation or uninstallation of brush or
in off position and lifting up the squeegee from
the floor. The operator must be equipped with
suitable personnel protection devices such as
gloves to reduce the risk of accidents. Proceed as
following:
OTHER
GEL/AGM
DIS-EV
WET
D
A
B
C
Figure 4

d +104°F (+40°C).
touch the ground slightly.
ith the ground, the front blademake good contact
the front blade touch the ground slightly.
ground,queegee blade make good contact with
If step 5 install the brush/pad but not
10
EF
C
BD
A
Figure 7
1. Insert key switch (40) and turn to “ON”.
2. Press the pedal (6) forward by foot to lift brush assembly (11) from the floor.
3. Rotate speed adjusting knob (42) in counterclockwise until the end.
4. Place the brush (A, Figure 5) or pad (B, Figure 5) center align with brush deck.
5. Press the pedal (6) backward by foot to lower down brush assembly (11). Sit on the seat, press the brush button (39)
and depress the pedal (23) slightly, the brush/pad can be assembled automatically. Repeat these steps until
brush/pad is installed.
6. successfully, please manually take the brush/pad down.
7. Depress the pedal (6) forward by foot to lift the brush assembly (11) from floor, press brush remove button (41) to
uninstall it automatically.
CAUTION!
Rotate the speed adjusting knob (42) to the minimum speed before depressing accelerate pedal (6) to
avoid the machine running too quickly when it is started. Make sure the brush/pad is installed correctly
before machine operating.
ADJUSTING THE BALANCE OF SQUEEGEE
1. Install the squeegee (13) and fasten the squeegee knob
(20), then connect the vacuum hose (19) to the squeegee.
2. Adjust the squeegee by squeegee adjusting handle (A,
Figure 7).
a) If there is gap between the ground and middle section
of rear squeegee blade (B), adjust the knob (A) in
counterclockwise direction (F) until all section of rear
s
b) If there is gap between the ground and both end
section of rear blade(C and D), adjust the knob (A) in
clockwise direction (E) until all section of rear blade
w
SOLUTION TANK FILLING
1. Open the water inlet cover (E, Figure 8).
2. Filling water or solution suitable for work performance through the water inlet with filter. The solution
temperature must not excee
3. Don’t overfill the tank, refer to water level indicator (G) for the water volume.
WARNING!
Use only low-foam and non-flammable detergents intended for automatic scrubber applications.
Drive motor inspection
1. Turn the key switch (A, Figure 9) to “ON”
2. Depress the accelerate pedal (C) slightly then loosen it to
check if the machine can be steered forward and stopped.
3. To ensure the security, confirm if the machine can be
stopped immediately by pressing the emergency button (B).
Rotate the emergency button to reset it.
CAUTION
Climbing capacity of the machine must not
exceed 10%.
CAUTION
The brake of drive motor is unstuck when the
motor works normally, it locks when the motor
stops working.
F
E
D
C
B
A
G
Figure 8

location.
9) switched to upper
the brake handle switched to lower location.
the brake handle (D, Figur
MENTAINENCE chapters for batteries charging].
the machine steer backward, or the machine will
Press brush button (B
tor (P). When the overloa
11
B
C
D
A
Figure 9
A
C
E
DB
F
G
HI
LMN
O
P
Q
R
ST
U
Figure 10
Brake unstuck - e
Brake locked
In some special cases, such as machine packing/unpacking,
machine fault etc., need to move the machine without drive
motor working, please manually set the brake to unstuck
status to move it.
To avoid any security risk, ensure to set the brake back to
locked status after machine movement.
MACHINE START AND STOP
Starting the machine
1. Prepare the machine as shown in previous paragraph.
2. Sit on the seat (L, Figure 10), insert the key switch (A) and turn
it to “ON”. If the green light (C) is on, the batteries are fully
charged for use. If the yellow light (E) or red light (D) is on,
batteries must be charged before operation. [Refer to
3. Lower the squeegee assembly to the floor.
NOTE
Make sure the squeegee assembly is lifted before
be stopped and LED screen show “Error”
information.
4. Lower the brush assembly to the floor.
NOTE
Make sure to turn off brush button before brush
assembly is lifted, and lift the brush assembly
before machine steers forward/backward.
5. ).
6. Depress the accelerate pedal (R), operate the machine
forward or backward by steering wheel (N) together with
forward-backward switch (H), you can adjust speed by speed
adjusting knob (I).
7. Adjust solution flow by solution adjusting button (G) base on
cleaning requirement.
8. You can charge your phone or pad through USB charging
port (M) when the key switch (A) is turned to “ON”.
9. Press the horn button (F) to warn people when necessary.
10. If necessary, press the emergency button for machine
emergency stop.
NOTE
The brush motor, vacuum motor, drive motor and
control circuit are protected by overload protec-
d protector trip, do not
reset it immediately without finding out the root
cause, and make sure the motor is cooling-off
before reset.
Stopping the machine
11. Loosen the accelerate pedal (R, Figure 10), the machine stops running.
12. Press brush button (B) to stop brush motor.
13. Lift brush assembly (T) by depressing the pedal (Q).
14. Lift squeegee assembly (U) by squeegee lifting/lowering lever (O), and a few seconds later the vacuum system will
be closed.
-

side (Bumper wheel side) of the machine as shown below in Figure
holder when the machine stops in one
12
A
D
B
C
Figure 12
15. Turn the key switch to “OFF”
16. Ensure the machine is stopped.
MACHINE OPERATION (SCRUBBING AND DRYING)
1. Start the machine according to procedures in previous paragraphs.
2. Start cleaning by following procedures in section of “Starting the machine”.
3. If necessary, stop the machine to adjust squeegee according to section “Adjusting the balance of squeegee”.
CAUTION!
To avoid any damage to the floor surface, turn off the brush/pad
place.
NOTE
For correct scrubbing/drying of floors at the sides of walls, we suggest to go near the walls with right
11.
Battery charging during the work
When there is green light (A, Figure 12) on, the batteries have
enough power for the machine to work normally; when all the
green lights off, the yellow light (C, Figure 12) is on, the power
of batteries are too low, please charge the batteries; when the
red light (B, Figure 12) flashes, the batteries has run out, the
vacuum motor and brush motor will be turned off
automatically a few seconds delay, please drive the machine for
batteries charging immediately.
CAUTION!
To avoid damaging the batteries and
shortening their working life, do not use the
machine once the batteries are flat.
Figure 11

5). Then
turn off the vacuum system by pressing
13
Figure 13
A
B
Figure 14
141414 14
A
D
C
B
Figure 15
TANK EMPTYING
An automatic float shut-off system (B, Figure 13) blocks the vacuum system when the recovery water tank (C) is full. The
vacuum system deactivation is signaled by a sudden increase in the vacuum system motor noise frequency, also the
floor has not dried.
CAUTION!
If the vacuum system turns off accidentally, (For
example, when the float is activated because of a
sudden machine movement), to resume the
operation:
the switch (D, Figure 12), then open the cover (A,
Figure 11) and check that the float inside the grid
(B) has gone down to the water level. Then close
the cover (A) and turn on the vacuum system by
pressing the switch (D, Figure 12).
When the recovery water tank (C, Figure 13) is full, empty it
according to the following procedure.
Recovery water tank emptying
1. Stop the machine.
2. Lift the brush/pad deck (H, Figure 12) by pressing the pedal (G).
3. Lift the squeegee with the lever (H).
4. Drive the machine to the appointed disposal area.
5. Empty the recovery tank with the drain hose (D). Then rinse the
tank with clean water.
CAUTION!
When draining the wastewater, the drain hose
must be folded (A, Figure 14) and put to a low
position (B, Figure 14) before opening the drain
hose cover. Do not make the outlet of the drain
hose upward to drain the water vertically in order
to avoid wastewater spilling onto the operator.
Solution/clean water tank emptying
6. Perform steps 1 to 4 in chapter “Recovery water tank emptying”.
7. Empty the solution tank through the outlet cover (A, Figure
1 , rinse the tank with clean water.
AFTER USING THE MACHINE
After working, before leaving the machine:
1. Remove the brushes/pad holder.
2. Empty the tanks (B and C, Figure 15) as shown in previous
paragraph.
3. Perform the daily maintenance procedures (see the
Maintenance chapter).
4. Store the machine in a clean and dry place, with the
brushes / pad holders and the squeegee lifted or removed.
MACHINE LONG INACTIVITY
If the machine is not going to be used for more than 30 days,
proceed as follows:
1. Perform the procedures shown in “AFTER USING THE
MACHINE” paragraph.
2. Disconnect the battery connector (D, Figure 15).
A
B
C
D
E
F
G
H

Brush/Pad holder carbon brush check or replacement
Brush/Pad holder cleaning
Always keeping the battery in a full charged state can extend its lifetime.
(32) or red LED (33) light is on, or at the end of each
working cycle.
(2) must be done by an authorized Service Center that qualified by our company.
Semiannually
that can be consulted at any authorized Service Center.
whether the fasteners or fittings are loose.
After nine hours using the machine for the first time, please check if any
14
USING FOR THE FIRST TIME
damage or abnormal situation, check
MAINTENANCE
WARNING!
Maintenance procedures must be performed after the machine is turned off and the battery charger
cable is disconnected. In addition, carefully read the safety chapters in the manual.
All scheduled or extraordinary maintenance procedures must be performed by qualified personnel or an authorized
Service Center. This guide only describes the general and common maintenance procedures.
For other maintenance procedures that are in below maintenance schedule table, please refer to the Service Manual
SCHEDULED MAINTENANCE TABLE
CAUTION!
The procedure marked with (1) must be performed when the machine is used after 9 hours for the first
time.
The procedure marked with
Procedure Daily, after
each use
Weekly Yearly
Battery charging
Squeegee cleaning
Tank cleaning
Tank sealing strip inspection
Float ball filter cleaning
Squeegee blade check and replacement
Cleaning water filter cleaning
Suction filter cleaning
WET battery fluid level check
Screw and nut tightness inspection （1）
（2）
Suction motor carbon brush check or replacement （2）
Drive system motor carbon brush check or
replacement (only for machine with traction)
（2）
Add lubricating oil for rotating parts （1）
BATTERY CHARGING
NOTE
Please charge the batteries when the yellow LED
CAUTION
CAUTION
Please charge the battery as soon as possible if the battery level is low. Otherwise, the lifespan of
battery can be reduced. It is better to check the battery at least once a week.

To be especially carefully when battery is
15
CAUTION!
charging, because there may be leaked
acid in the process of charging.
Battery acid is corrosive, if it accidentally
comes into contact with the skin or eyes,
rinse immediately with plenty of clean
water and go to see a doctor.
The preparation steps to charge the
batteries
1. Open the recovery tank cover (B, Figure 16) to check if
the recovery tank (C) is empty, or empty the recovery
tank through the drain hose (A).
2. Drive the machine to designated charging area.
3. Turn the key switch to “OFF”.
4. This step only for WET batteries:
 Clean the battery surface if necessary.
 Check the battery electrolyte level of the
batteries (D), if necessary, open the cover to full
fill electrolyte, and then recover it.
 Keep the cover opened during charging.
5. Select one of below charging mode base on the
selected charger type.
Use on-board charger for battery charging
6. Connect the battery charger cable (A, Figure 17) to the
electric mains (G), and then all machine functions
except charging are cut off automatically.
The normally on red LED (B) states that the machine is
in process of charging.
7. The batteries are fully charged when the green LED (C)
becomes on.
8. Disconnect battery charge cable from electric mains after charging is completed, and then store the battery charger
cable in the storage box (D).
NOTE
For further information about on-board charger (E, Figure 17), please refer to relevant manual from
service center.
BRUSH/PAD CLEANING
CAUTION!
It is recommended to wear gloves when
cleaning the brush/pad holder, since it may
contain sharp fragments.
1. Take the brush/pad holder off base on procedures in
previous sections.
2. Clean the brush/pad holder using water and detergent.
3. Check the integrity and abrasion conditions of the bristle
on the brush, if necessary, replace the brush.
4. Check the abrasion condition of the polishing pad, if
necessary, replace it.
D
A
B
C
E
Figure 16
B
A
C
D
Figure 18
Figure 17
E
C
G
A
B
D

16
reverse order of disassembly. After the blade repla
clean the filter screen (B), and then fix them back
USER MANUAL ENGLISH
B
C
A
Figure 20
SOLUTION FILTER CLEANING
1. Drive the machine to the flat ground.
2. Make sure the machine is off.
3. Empty the solution tank (optional step).
. Take down the solution filter cover (A, Figure 18) to
to the
filter support (D).
NOTE
The filter screen ( ) must be correctly
positioned to the housing of filter support
(D).
SQUEEGEE CLEANING
NOTE
The squeegee must be clean and its blades
must be in good conditions in order to get
good drying.
CAUTION
It is advisable to wear protective gloves
when cleaning the squeegee because there
may be sharp debris.
1. Drive the machine on a level floor.
2. Turn the key switch (A, Figure 19) to “OFF”.
3. Lower the squeegee (B) with the lever (C).
. Loosen the knobs (D) and remove the squeegee.
5. Disconnect the vacuum hose (E) from the squeegee.
6. Clean the steel or aluminum squeegee, especially the
compartments (A, Figure 20) and the holes (B). Check
the integrity, cuts and tears of the front blade (B) and
rear blade (C), if necessary, replace them according to
procedures in the following paragraph.
7. Assemble the squeegee in the reverse order of
disassembly.
SQUEEGEE LADE CHECK AND REPLACEMENT
1. Clean the steel or the aluminum squeegee, as shown in the previous paragraph.
2. Check that the edges (E, Figure 21) of the front blade (C) and the edges (F) of the rear blade (D) lay down on the
same level, along their length; if necessary adjust their height according to the following procedure:
• Remove the tie rod (G), disengage the fasteners (M) and adjust the rear blade (D), then engage the fasteners (M)
and install the tie rod (G).
• Loosen the knobs (I) and adjust the front blade (C), then tighten the knobs.
3. Check the front blade (C) and rear blade (D) for wear, cuts and tears; if necessary replace them according to the
following procedure. Check that the front corner (J) of the rear blade (D) is not worn; if necessary overturn the
blade to replace the worn corner with an integral one. If the other corners are worn too, replace the blade
according to the following procedure:
• Remove the tie rod (G), disengage the fastener (M) and remove the retaining strip (K), then replace/overturn the
rear blade (D). Assemble the blade in the reverse order of disassembly.
• Unscrew the knobs (I) and remove the retaining strip (L), then replace front blade (C). Assemble the blade in the
cement (or overturning), adjust the height as shown in the
previous step.
. Connect the vacuum hose (A, Figure 22) to the squeegee.
5. Install the squeegee (B) and screw down the knobs (C).
6. If necessary, adjust the squeegee balance adjusting knob (D).
A
B
C
D
E
D
Figure 19

17
position where it can be removed from the tank, an
TANK AND VACUUM GRID WITH FLOAT CLEANING, AND COVER GASKET CHECK
1. Drive the machine on a level floor.
2. Ensure that the machine is off and the ignition key ( 0)
has been removed.
3. Turn the recovery tank lid (A, Figure 23) 90 degree
d then
take down the float ball filter (P) from the tank.
. Clean the recovery tank lid (A), recovery tank (B), clean
water tank (C) and the float ball filter support frame (E).
Empty the recovery tank with the drain hose (15).
5. If necessary, follow the symbols “OPEN” and “CLOSE” as
shown in Figure 23 to open the bottom cover (F) of float
ball filter and then clean the float ball (D), filter support
frame (E) and filter sponge (I). After cleaning, fix the float
ball (D) into the filter support frame (E) and then align
the mark groove (L) of the bottom cap (F) of the float ball
filter with the mark groove (L) of the float filter support
frame (E). Screw the bottom cap of the float ball filter
tight, and fix the filter sponge (I) onto the float filter
support frame (E). Finally, connect it to the sewage
suction hose (M).
6. Inspect the integrity of the tank sealing strip.
NOTE
Tank sealing strip (G) makes to produce the vacuum inside the tank when suction motor works. The
tank must be sealed can effectively absorb the water from the ground to recovery tank.
7. Check whether the contact surface of sealing strip (G) is integrity and sealing is sufficient. If necessary, take the
sealing strip of the tank out of the groove (H) and replace it. Assembly the new sealing strip as shown in Figure 23,
the joint should be back in the middle area.
8. Close the recovery tank lid (A).
Figure 22
A
CDCB
Figure 23
B
A
M
D
J
I
C
A
G
M
I
I
K
D
F
C
L
E
Figure 21
I
E
D
F
L
P
M
A
B
C
H
G