Tripp Lite P937-000 User manual

1
Owner’s Manual
Este manual esta disponible en español en la página de
Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de
Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте
компании Tripp Lite по адресу: www.tripplite.com
40-Pin Male IDE to
2.5”/3.5”/5.25” SATA Adapter
Model: P937-000
1111 W. 35th Street, Chicago, IL 60609
www.tripplite.com/support
Copyright © 2017 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
16-09-002-93361F-EN.indd 1 2/24/2017 11:01:36 AM

2
Product Features
System Requirements
Package Includes
Installation
• Connect a SATA drive to an IDE/ATA motherboard
• Ideal for older motherboards that do not support SATA
• Optical Disk Drive (ODD) support, including Blu-ray™, DVD and
CD-ROM drives
• Supports data transfer rates up to 6 Gbps (SATA I/II/III)
• Compatible with Ultra ATA 133 specification
• Plug-and-Play; no software or drivers required
• Computer with an available IDE connection
• SATA drive
• 40-pin IDE drive cable
• P937-000
• 4-Pin Molex Power Cable
• Owner’s Manual
Note: To use the installed SATA drive as a bootable device, it must be able to
operate in Master Mode
1. Turn off the computer, unplug its power cord, and disconnect all
peripheral devices (e.g. monitor, keyboard, etc.).
2. Open the computer chassis. Make sure the hard drive is fastened
to the chassis appropriately.
16-09-002-93361F-EN.indd 2 2/24/2017 11:01:36 AM

3
Installation
3. Using the jumper (J3) provided on the circuit board, select the
mode you want the installed SATA drive to operate under (S for
Slave, M for Master).
4. Connect the SATA drive to the circuit board using the designated
SATA power and data ports. Insert the connector on the board into
the drive ports.
5. Connect the LP4 end of the provided 4-Pin Molex Cable to the
computer’s power supply and the SP4 end to the adapter unit’s
power port.
6. Using a 40-Pin IDE cable, connect the IDE connector on the
adapter unit’s circuit board to an available IDE port on the
motherboard. The pin positioning will ensure a proper connection.
An arrow on the circuit board indicates Pin 1 of the IDE connector.
7. Replace the computer chassis and power cord on the computer.
Warranty & Product Registration
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period
of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is
limited to repairing or replacing (at its sole option) any such defective products. To obtain service
under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP
LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an
authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied
by a brief description of the problem encountered and proof of date and place of purchase.
This warranty does not apply to equipment which has been damaged by accident, negligence or
misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable
for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of
software, loss of data, costs of substitutes, claims by third parties, or otherwise.
16-09-002-93361F-EN.indd 3 2/24/2017 11:01:36 AM

4
Warranty & Product Registration
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically
entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the
user’s authority to operate this equipment.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations, when customers buy new electrical and electronic equipment from Tripp Lite
they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies
depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without
notice.
1111 W. 35th Street, Chicago, IL 60609 • www.tripplite.com/support
16-09-002 93-361F_RevA
16-09-002-93361F-EN.indd 4 2/24/2017 11:01:37 AM