Tripp Lite N784-001-SC-MM User manual

1
Owner’s Manual
10/100
Media Converters
Models: N784-001-SC-MM (850nm),
N784-001-SC-15 (1310nm)
10/100/1000
Media Converters
Models: N785-001-LC-MM (850nm),
N785-001-SC-MM (850nm),
N785-001-SC (1310nm)
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an ISOBAR6ULTRA
surge protector—a $50 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
All trademarks are the property of their respective owners.
14-05-207-93336D.indd 1 6/16/2014 4:47:13 PM

2
Product Features
• N784-001-SC-15 extends a 10/100Mbps Ethernet
connection over singlemode fiber cable up to
15 km
• N784-001-SC-MM extends a 10/100Mbps
Ethernet connection over multimode fiber cable up
to 550 m
• N785-001-SC extends a 10/100/1000Mbps
Ethernet connection over multimode fiber cable up
to 2 km
• N785-001-LC-MM and N785-001-SC-MM extend
a 10/100/1000Mbps Ethernet connection over
multimode fiber cable up to 550 m
• LED indicators monitor the Ethernet and fiber link
status of the media converters
• Supports both full-duplex and half-duplex operation
• Supports Auto MDI / MDI-X
Package Contents
• Media Converter
• External Power Supply
• Owner’s Manual
14-05-207-93336D.indd 2 6/16/2014 4:47:13 PM

3
Optional Accessories
• N001-Series Cat5e Snagless Patch Cables
• N201-Series Cat6 Snagless Patch Cables
• N306-Series Duplex Multimode 62.5/125 Fiber
Patch Cables (SC/SC)
• N320-Series Duplex Multimode 62.5/125 Fiber
Patch Cables (LC/LC)
• N356-Series Duplex Singlemode 8.3/125 Fiber
Patch Cables (SC/SC)
• N506-Series Duplex Multimode 50/125 Fiber Patch
Cables (SC/SC)
• N520-Series Duplex Multimode 50/125 Fiber Patch
Cables (LC/LC)
Installation
Note:
1. The following installation instructions refer to an installation
in which two media converters are used.
2. The installation diagram on the next page features a
N784-001-SC-MM. Connections are the same for all
models, with only the specs of the media converter being
different. (See the Specifications section in this manual for
details on your media converter.)
3. To avoid damage due to Electrostatic Discharge (ESD), it is
recommended that you handle the product while wearing
an ESD wrist grounding strap; or, by touching a conductive
surface (such as metal) to discharge any potential ESD prior
to handling the product.
14-05-207-93336D.indd 3 6/16/2014 4:47:13 PM

4
Installation
1Connect the RJ45 port on the media converter to your
network using a Cat5e/6 cable.
2Connect the media converter to a second identical
media converter using the appropriate type of fiber cable,
making sure to connect the TX port on one unit to the
RX port on the other.
Note: Reference the Product Features section to
determine which type of fiber cable is supported by your
media converter.
3Connect the RJ45 port on the second media converter to
your network device (workstation, hub, switch, etc.) using
a Cat5e/6 cable.
4Connect the external power supplies that came with each
media converter, and plug them into a power source.
Network
Power Source Power Source
Network Device
L /A
L /A L /A L /A
1 3
4 4
2
14-05-207-93336D.indd 4 6/16/2014 4:47:13 PM

5
LED Status Table
LED Status Description
FP – PWR On The unit is powered on
FP – PWR Off The unit is not powered on
FP – L/A On A link is detected between the
connected fiber ports
FP – L/A Blinking Fiber data transmission is taking
place
FP – L/A Off No link is detected between fiber
ports
FP – SD On A fiber signal is detected
FP – SD Off No fiber signal is detected
TP – SPD On 1000Mbps (or 100Mbps)*
TP – SPD Off 100Mbps (or 10Mbps)*
TP – L/A On A UTP link is detected
TP – L/A Blinking UTP data transmission is taking
place
TP – L/A Off No UTP link is detected
TP – FDX/COL On The unit is operating in Full-Duplex
mode
TP – FDX/COL Off The unit is operating in Half-Duplex
mode
*10/100 Media Converter description is shown in parenthesis.
14-05-207-93336D.indd 5 6/16/2014 4:47:14 PM

6
Specifications
Specification
N784-001-SC-MM
N784-001-SC-15 N785-001-LC-MM N785-001-SC-MM N785-001-SC
Optical Wavelength (nm) Multimode (850)
Singlemode (1310) Multimode (850) Multimode (1310)
Network Speed 10/100
10/100/1000
Transmission Distance 550 m
15 km 550 m 2 km
Duplex Mode
Full / Half (Auto-Detect)
Optical Output Power Range (dBm) -8 to -3
-15 to -3 -8 to -3
Optical Input Power Range (dBm) ≤-19 ≤
-34 ≤-19
Power Budget (dBm) 11
19 11
Power Supply Input
100-240V, 50/60Hz
Power Supply Output
5V, 1.2A
Operating Temperature
0° to 60° C (32° to 140° F)
Storage Temperature
-20° to 70° C (-4° to 158° F)
Relative Humidity
5 to 90% RH, Non-Condensing
Unit Dimensions (HxWxD)
25.4 x 93.98 x 71.12 mm (1 x 3.7 x 2.8 inches)
Unit Weight 0.45 kg (1 lb)
0.47 kg (1.03 lb) 0.45 kg (1 lb)
14-05-207-93336D.indd 6 6/16/2014 4:47:14 PM

7
Specifications
Specification
N784-001-SC-MM N784-001-SC-15
N785-001-LC-MM N785-001-SC-MM N785-001-SC
Optical Wavelength (nm) Multimode (850) Singlemode (1310)
Multimode (850) Multimode (1310)
Network Speed 10/100
10/100/1000
Transmission Distance 550 m 15 km
550 m 2 km
Duplex Mode
Full / Half (Auto-Detect)
Optical Output Power Range (dBm) -8 to -3 -15 to -3
-8 to -3
Optical Input Power Range (dBm) ≤-19 ≤-34
≤-19
Power Budget (dBm) 11 19
11
Power Supply Input
100-240V, 50/60Hz
Power Supply Output
5V, 1.2A
Operating Temperature
0° to 60° C (32° to 140° F)
Storage Temperature
-20° to 70° C (-4° to 158° F)
Relative Humidity
5 to 90% RH, Non-Condensing
Unit Dimensions (HxWxD) 25.4 x 93.98 x 71.12 mm (1 x 3.7 x 2.8 inches)
Unit Weight 0.45 kg (1 lb)
0.47 kg (1.03 lb) 0.45 kg (1 lb)
14-05-207-93336D.indd 7 6/16/2014 4:47:14 PM

8
Warranty & Product Registration
1-YEAR LIMITED WARRANTY
Seller warrants this product, if used in accordance with all
applicable instructions, to be free from original defects in
material and workmanship for a period of 1 year from the date
of initial purchase. If the product should prove defective in
material or workmanship within that period, Seller will repair or
replace the product, in its sole discretion. Service under this
Warranty can only be obtained by your delivering or shipping
the product (with all shipping or delivery charges prepaid) to:
Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller
will pay return shipping charges.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR
TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE
OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS
WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow
limitations on how long an implied warranty lasts, and some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific
legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should determine prior to use
whether this device is suitable, adequate or safe for the use
intended. Since individual applications are subject to great
variation, the manufacturer makes no representation or
warranty as to the suitability or fitness of this device for any
specific application.
14-05-207-93336D.indd 8 6/16/2014 4:47:14 PM

9
Warranty & Product Registration
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty
for your new Tripp Lite product. You’ll be automatically entered
into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some
restrictions apply. See website for details.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
14-05-207-93336D.indd 9 6/16/2014 4:47:14 PM

10
Warranty & Product Registration
Any changes or modifications to this equipment not expressly
approved by Tripp Lite could void the user’s authority to operate
this equipment.
WEEE Compliance Information for Tripp Lite Customers
and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment
(WEEE) Directive and implementing regulations,
when customers buy new electrical and electronic
equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one,
like-for-like basis (this varies depending on the
country)
• Send the new equipment back for recycling when
this ultimately becomes waste
Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the
failure of the life support equipment or to significantly affect its
safety or effectiveness is not recommended. Do not use this
equipment in the presence of a flammable anesthetic mixture
with air, oxygen or nitrous oxide.
Tripp Lite follows a policy of continuous improvement. Product
specifications are subject to change without notice.
14-05-207-93336D.indd 10 6/16/2014 4:47:14 PM

11
Notes
14-05-207-93336D.indd 11 6/16/2014 4:47:14 PM

12
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
14-05-207 93-336D_RevA
14-05-207-93336D.indd 12 6/16/2014 4:47:14 PM