Tripp Lite B096-048 User manual

1
Owner’s Manual
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Console Server Management Switch
Models: B096-016 / B096-048
&
Console Server with PowerAlert
Model: B092-016
Tripp Lite World Headquarters
1111 W. 35th Street, Chicago, IL 60609 USA
[phone] (USA) • 773.869.1212 (International)
www.tripplite.com
Copyright © 2009 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.

2
INDEX
1. INTRODUCTION 9
2. INSTALLATION 14
2.1 Models 14
2.1.1 Kit components: B096-048 and B096-016 Console Server Management Switch 14
2.1.2 Kit components: B092-016 Console Server with PowerAlert 15
2.2 Power connection 15
2.2.1 Power: Console Server Management Switch 15
2.2.2 Power: Console Server with PowerAlert 16
2.3 Network connection 16
2.4 Serial Port connection 16
2.5 USB Port Connection 17
2.6 Rackmount Console / KVM Connection (B092-016 only) 17
3. INITIAL SYSTEM CONFIGURATION 18
3.1 Management Console Connection 18
3.1.1 Connected computer set up 18
3.1.2 Browser connection 19
3.1.3 Initial B092-016 connection 21
3.2 Administrator Password 21
3.3 Network IP address 22
3.3.1 IPv6 configuration 23
3.4 System Services 24
3.5 Communications Software 27
3.5.1 SDT Connector 27
3.5.2 PuTTY 27
3.5.3 SSHTerm 28
3.6 Management Network Configuration (B096-048/016 only) 29
3.6.1 Configure Management Switch as a Management LAN gateway 29
3.6.3 Configure Management Switch for Failover or broadband OOB 32
4. SERIAL PORT AND NETWORK HOST 33
4.1 Configuring Serial Ports 33
4.1.1 Common Settings 34
4.1.2 Console Server Mode 35

3
4.1.3 SDT Mode 39
4.1.4 Device (RPC, UPS, EMD) Mode 39
4.1.5 Terminal Server Mode 39
4.1.6 Serial Bridging Mode 40
4.1.7 Syslog 41
4.2 Add/Edit Users 41
4.3 Authentication 44
4.4 Network Hosts 44
4.5 Trusted Networks 46
4.6 Serial Port Cascading 47
4.6.1 Automatically generate and upload SSH keys 47
4.6.2 Manually generate and upload SSH keys 48
4.6.3 Configure the Slaves and their serial ports 50
4.6.4 Managing the Slaves 51
5. FAILOVER AND OUT-OF-BAND ACCESS 52
5.1 OoB Dial-In Access 52
5.1.1 Configure dial-in PPP 52
5.1.2 Using SDT Connector client for dial-in 54
5.1.3 Set up Windows XP/ 2003/Vista client for dial-in 54
5.1.4 Set up earlier Windows clients for dial-in 55
5.1.5 Set up Linux clients for dial-in 56
5.2 OoB Broadband Access (B096-048/016 only) 56
5.3 Broadband Ethernet Failover (B096-048/016 only) 56
5.4 Dial-Out Failover 58
6. SECURE TUNNELING AND SDT CONNECTOR 60
6.1 Configuring for SDT Tunneling to Hosts 61
6.2 SDT Connector Configuration 61
6.2.1 SDT Connector client installation 62
6.2.2 Configuring a new gateway in the SDT Connector client 63
6.2.3 Auto-configure SDT Connector client with the user’s access privileges 64
6.2.4 Make an SDT connection through the gateway to a host 65
6.2.5 Manually adding hosts to the SDT Connector gateway 66
6.2.6 Manually adding new services to the new hosts 67
6.2.7 Adding a client program to be started for the new service 69
6.2.8 Dial- in configuration 70

4
6.2.9 Choosing an alternate SSH client (e.g. PuTTY) 70
6.3 SDT Connector to Management Console 75
6.4 SDT Connector - Telnet or SSH connect to serially attached devices 76
6.5 Using SDT Connector for out-of-band connection to the gateway 77
6.6 Importing (and exporting) preferences 79
6.7 SDT Connector Public Key Authentication 79
6.8 Setting up SDT for Remote Desktop access 80
6.8.1 Enable Remote Desktop on the target Windows computer to be accessed 80
6.8.2 Configure the Remote Desktop Connection client 81
6.9 SDT SHH Tunnel for VNC 85
6.9.1 Install and configure the VNC Server on the computer to be accessed 85
6.9.2 Install, configure and connect the VNC Viewer 86
6.10 Using SDT to IP connect to hosts that are serially attached to the gateway 88
6.10.1 Establish a PPP connection between the host COM port and Console Server 88
6.10.2 Set up SDT Serial Ports on Console Server 91
6.10.3 Set up SDT Connector to ssh port forward over the Console Server Serial Port 92
7. ALERTS AND LOGGING 93
7.1 Configure SMTP/SMS/SNMP/Nagios alert service 93
7.1.1 Email alerts 93
7.1.2 SMS alerts 94
7.1.3 SNMP alerts 95
7.1.4 Nagios alerts 96
7.2 Activate Alert Events and Notifications 96
7.2.1 Add a new alert 97
7.2.2 Select general alert type 98
7.2.3 Configuring environment and power alert type 99
7.3 Remote Log Storage 100
7.4 Serial Port Logging 101
7.5 Network TCP or UDP Port Logging 102
POWER & ENVIRONMENTAL MANAGEMENT 103
8.1 Remote Power Control (RPC) 103
8.1.1 RPC connection 103
8.1.2 RPC alerts 105
8.1.3 RPC status 105

5
8.1.4 User power management 105
8.2 Uninterruptible Power Supply Control (UPS) 106
8.2.1 Managed UPS connections 106
8.2.2 Configure UPS powering the Console Server 109
8.2.3 Configuring powered computers to monitor a Managed UPS 110
8.2.4 UPS alerts 111
8.2.5 UPS status 111
8.2.6 Overview of Network UPS Tools (NUT) 111
8.3 Environmental Monitoring 113
8.3.1 Connecting the EMD 114
8.3.2 Environmental alerts 115
8.3.3 Environmental status 115
AUTHENTICATION 117
9.1 Authentication Configuration 117
9.1.1 Local authentication 118
9.1.2 TACACS authentication 118
9.1.3 RADIUS authentication 119
9.1.4 LDAP authentication 120
9.1.5 RADIUS/TACACS user configuration 121
9.2 PAM (Pluggable Authentication Modules) 122
9.3 Secure Management Console Access 123
NAGIOS INTEGRATION 125
10.1 Nagios Overview 125
10.2 Central management 126
10.2.1 Set up central Nagios server 126
10.2.2 Set up distributed Console Servers 127
10.3 Configuring Nagios distributed monitoring 129
10.3.1 Enable Nagios on the Console Server 129
10.3.2 Enable NRPE monitoring 131
10.3.3 Enable NSCA monitoring 132
10.3.4 Configure selected Serial Ports for Nagios monitoring 132
10.3.5 Configure selected Network Hosts for Nagios monitoring 133
10.3.6 Configure the upstream Nagios monitoring host 134
10.4 Advanced Distributed Monitoring Configuration 135
10.4.1 Sample Nagios configuration 135

6
10.4.2 Basic Nagios plug-ins 138
10.4.3 Additional plug-ins 138
11. SYSTEM MANAGEMENT 140
11.1 System Administration and Reset 140
11.2 Upgrade Firmware 141
11.3 Configure Date and Time 142
12. STATUS REPORTS 143
12.1 Port Access and Active Users 143
12.2 Statistics 143
12.3 Support Reports 144
12.4 Syslog 144
13. MANAGEMENT 146
13.1 Device Management 146
13.2 Port and Host Management 146
13.3 Power Management 147
13.4 Serial Port Terminal Connection 147
13.5 Remote Console Access (B092-016 only) 149
14. BASIC CONFIGURATION - LINUX COMMANDS 151
14.1 The Linux Command line 152
14.2 Administration Configuration 154
System Settings 154
Authentication Configuration 154
14.3 Date and Time Configuration 155
14.4 Network Configuration 156
IP Configuration 156
Dial-in Configuration 157
Services Configuration 158
14.5 Serial Port Configuration 159
Serial Port Settings 159
Supported Protocol Configuration 160
Users 160
Trusted Networks 161
14.6 Event Logging Configuration 162
Remote Serial Port Log Storage 162

7
Alert Configuration 163
14.7 SDT Host Configuration 163
SDT Host TCP Ports 163
14.8 Configuration backup and restore 165
14.9 General Linux command usage 166
15. ADVANCED CONFIGURATION 168
15.1 Advanced Portmanager 169
15.2 External Scripts and Alerts 171
15.3 Raw Access to Serial Ports 173
15.4 IP- Filtering 174
15.5 Modifying SNMP Configuration 176
Adding more than on SNMP server 177
15.6 Secure Shell (SSH) Public Key Authentication 178
SSH Overview 178
Generating Public Keys (Linux) 179
Installing the SSH Public/Private Keys (Clustering) 180
Installing SSH Public Key Authentication (Linux) 180
Generating Public/Private keys for SSH (Windows) 182
Fingerprinting 184
SSH tunneled serial bridging 185
SDT Connector Public Key Authentication 188
15.7 Secure Sockets Layer (SSL) Support 189
15.8 HTTPS 190
15.9 Power Strip Control 192
PowerMan 192
pmpower 194
Adding new RPC devices 194
15.10 IPMItool 196
15.11 Scripts for Managing Slaves 200
16. THIN CLIENT (B092-016) 202
16.1 Local Client Service Connections 202
16.1.1 Connect- serial terminal 204
16.1.2 Connect- browser 204
16.1.3 Connect- VNC 205

8
16.1.4 Connect- SSH 206
16.1.5 Connect- IPMI 207
16.1.6 Connect- Remote Desktop (RDP) 208
16.1.7 Connect- Citrix ICA 209
16.1.8 Connect- PowerAlert 209
16.2 Advanced Control Panel 210
16.2.1 System: Terminal 210
16.2.2 System: Shutdown / Reboot 211
16.2.3 System: Logout 211
16.2.4 Custom 211
16.2.5 Status 211
16.2.6 Logs 211
16.3 Remote control 212
Appendix A Hardware Specification 213
Appendix B Serial Port Connectivity 214
Appendix C End User License Agreement 216
Appendix D Service and Warranty 223

9
1. INTRODUCTION
This Manual
This User Manual is provided to help you get the most from your B096-016 / B096-048 Console Server
Management Switch or B092-016 Console Server with PowerAlert product. These products are referred
to generically in this manual as Console Servers.
Once configured, you will be able to use your Console Server to securely monitor, access and control the
computers, networking devices, telecommunications equipment, power supplies and operating
environment in your data center, branch office or communications room. This manual guides you in
managing this infrastructure locally (at the rack side or across your operations or management LAN or
through the local serial console port), and remotely (across the Internet, private network or via dial up).
FCC Information
This is an FCC Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures. This equipment has been tested and
found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
RoHS
This product is RoHS compliant.
User Notice
All information, documentation and specifications contained in this manual are subject to change
without prior notification by the manufacturer. The manufacturer makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims
any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's
software described in this manual is sold or licensed `as is'. Should the programs prove defective
following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the
entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from
any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference caused by
unauthorized modifications to this device. It is the responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this system if the
correct operational voltage setting was not selected prior to operation.
RODUCTION

10
Please take care to follow the safety precautions below when installing and
operating the Console Server:
Do not remove the metal covers. There are no operator-serviceable
components inside. Opening or removing the cover may expose you to
dangerous voltage which may cause fire or electric shock. Refer all service
to Tripp Lite qualified personnel
To avoid electric shock the power cord protective grounding conductor
must be connected through to ground
Always pull on the plug, not the cable, when disconnecting the power cord
from the socket
Do not connect or disconnect the Console Server during an electrical storm
Also it is recommended you use a surge suppressor or UPS to protect the
equipment from transients
Manual Organization
This User Manual covers all aspects of installation, configuration and operation and an overview of the
information found in the manual is provided below.
1. Introduction An overview of the features of the Console Server and information on
this manual
2. Installation Details physical installation of the Console Server and the
interconnection of controlled devices
3. System Configuration Describes the initial installation and configuration using the
Management Console of the Console Server on the network and the
services that will be supported
4. Serial and Network Covers configuring serial ports and connected network hosts, and
setting up Users and Groups
5. Failover and OoB dial-in Describes setting up the high-availability access features of the Console
Server
6. Secure Tunneling (SDT) Covers secure remote access using SSH and configuring for RDP, VNC,
HTTP, HTTPS, etc. access to network and serially connected devices
7. Alerts and Logging Explains the setting up of local and remote event/ data logs and
triggering SNMP and email alerts
8. Power & Environment Management of USB, serial and network attached Power Distribution
units and UPS units including Network UPS Tool (NUT) operation and
IPMI power control. EMD environmental sensor configuration
9. Authentication All access to the Console Server requires usernames and passwords
which are locally or externally authenticated

11
10. Nagios Integration Setting Nagios central management with SDT extensions and
configuring the Console Server as a distributed Nagios server
11. System Management Covers access to and configuration of services to be run on the Console
Server
12. Status Reports View the status and logs of serial and network connected devices (ports,
hosts, power and environment)
13. Management Includes port controls and reports that can accessed by Users
14. Basic Configuration Command line installation and configuration using the config command
15. Advanced Config More advanced command line configuration activities where you will
need to use Linux commands
16. Thin Client Configuration and use of the thin client and other applications (including
Power Alert) embedded in the Console Server with PowerAlert (B092-
016) product
Types of users
The Console Server supports two classes of users:
I. Administrative users: Those who will be authorized to configure and control the Console Server; and
to access and control all the connected devices. These administrative users will be set up as members
of the admin user group. Any user in this class is referred to generically in this manual as an
Administrator. An Administrator can access and control the Console Server using the config utility,
the Linux command line or the browser-based Management Console. By default the Administrator
has access to all services and ports to control all the serial connected devices and network connected
devices (hosts).
II. Users: Embraces those who have been set up by the Administrator with specific limits on their
access and control authority. These users are set up as members of the users user group (or some
other user groups the Administrator may have added). They are only authorized to perform specified
controls on specific connected devices and are referred to as Users. These Users (when authorized)
can access serial or network connected devices; and control these devices using the specified
services (e.g. Telnet, HHTPS, RDP, IPMI, Serial over LAN, Power Control). An authorized User can also
use the Management Console to access configured devices and review port logs.
In this manual, when the term user (lower case) is used, it is referring to both the above classes of users.
This document also uses the term remote users to describe users who are not on the same LAN segment
as the Console Server. These remote users may be Users,who are on the road connecting to managed
devices over the public Internet, or it may be an Administrator in another office connecting to the
Console Server itself over the enterprise VPN, or the remote user may be in the same room or the same
office but connected on a separate VLAN to the Console Server.
Management Console
The Console Server Management Console runs in a browser. It provides a view of your Console Server
Management Switch (B096-016/048) or Console Server with PowerAlert (B092-016) product and all the
connected equipment. Administrators can use the Management Console, either locally or from a remote

12
location, to configure the Console Server, set up Users, configure the ports and connected hosts, and set
up logging and alerts.
An authorized User can use the Management Console to access and control configured devices, review
port logs, use the in-built java terminal to access serially attached consoles and control power to
connected devices.
The Console Server runs an embedded Linux operating system. Experienced Linux and UNIX users may
prefer to undertake configuration at the command line. As an Administrator you can get command line
access by connecting through a terminal emulator or communications program to the console serial
port; or by SSH or Telnet connecting to the Console Server over the LAN; or by connecting to the
Console Server through an SSH tunnel using the SDTConnector.
The B092-016 Console Server also has PowerAlert software and a selection of thin clients embedded
(RDP, Firefox etc). You will be able to use these consoles as well as the standard Management Console
for access and control.
Manual Conventions
This manual uses different fonts and typefaces to show specific actions:
Note Text presented like this indicates issues which need to be noted

13
Text presented like this highlights important issues and it is essential you read
and take heed of these warnings
Text presented with an arrow head indent indicates an action you should take as part of the
procedure.
Bold text indicates text that you type, or the name of a screen object (e.g. a menu or button) on the
Management Console.
Italic text is also used to indicate a text command to be entered at the command line level.
Publishing history
Date Revision Update details
January 2009 0.9 Initial draft
February 2009 0.91 Pre-release

14
2. INSTALLATION
Introduction
This chapter describes the physical installation of the Console Server hardware and connection to
controlled devices
2.1 Models
There are a number of Console Server models, each with a different number of network, USB and serial
ports and power supplies:
Serial
Ports
Network
Ports
Console
Port
USB
Port
Modem Power
B096-048 48 2 1 1 Internal Dual AC Universal Input
B096-016 16 2 1 1 Internal Dual AC Universal Input
B092-016 16 1 1+KVM 4 - Single AC Universal Input
2.1.1 Kit components: B096-048 and B096-016 Console Server Management Switch
B096-048 or B096-016
Console Server Management Switch
2 x Cable UTP Cat5 blue
Connectors
DB9F-RJ45S straight and cross-over
Dual IEC AC power cords
Quick Start Guide and CD-ROM
Unpack your Console Server Management Switch kit and verify you have all the parts shown
above, and that they all appear in good working order

15
If you are installing your Console Server Management Switch in a rack you will need to attach
the rack mounting brackets supplied with the unit, and install the unit in the rack. Take care to
head the Safety Precautions
Connect your Console Server Management Switch to the network, to the serial ports of the
controlled devices, and to power as outlined below
2.1.2 Kit components: B092-016 Console Server with PowerAlert
B092-016
Console Server with PowerAlert
2 x Cable UTP Cat5 blue
Connector DB9F-RJ45S straight and DB9F-
RJ45S cross-over
AC power cable
Quick Start Guide and CD-ROM
Unpack your Console Server and verify you have all the parts shown above, and that they all
appear in good working order
If you are installing your Console Server in a rack, you will need to attach the rack mounting
brackets supplied with the unit, and install the unit in the rack. Take care to heed the Safety
Precautions listed earlier
Proceed to connect your B092-016 to the network, to the serial and USB ports of the controlled
devices, to any rack side LCD console or KVM switch, and to power as outlined below
2.2 Power connection
2.2.1 Power: Console Server Management Switch
The B096-048/16 Console Server Management Switch has dual universal AC power supplies with auto
failover built in. These power supplies each accept AC input voltage between 100 and 240 VAC with a
frequency of 50 or 60 Hz and the total power consumption per Console Server is less than 30W. Two IEC
AC power sockets are located at the rear of the metal case, and these IEC power inlets use conventional
IEC AC power cords. A North American power cord is provided by default. Power cords for other regions
are available separately from Tripp Lite.

16
2.2.2 Power: Console Server with PowerAlert
The standard B092-016 Console Server has a built-in universal auto-switching AC power supply. This
power supply accepts AC input voltage between 100 and 240 VAC with a frequency of 50 or 60 Hz and
the power consumption is less than 40W.
The AC power socket is located at the rear of the B092-016. This power inlet uses a conventional AC
power cord. A North American power cord is provided by default. Power cords for other regions are
available separately from Tripp Lite.
2.3 Network connection
The RJ45 10/100 LAN port is located on the rear of the B092-016 Console Server, and on the front of the
B096-048/016 Console Server Management Switch. All physical connections are made using industry
standard Cat5e patch cables (Tripp Lite N001 and N002 series cables). Ensure you only connect the LAN
port to an Ethernet network that supports 10Base-T/100Base-T. For the initial configuration of the
Console Server you must connect a computer to the Console Server’s principal network port.
2.4 Serial Port connection
The RJ45 serial ports are located on the rear of the B092-016 Console Server and on the front of the
B096-048/016 Console Server Management Switch. These Console Servers use the RJ45 pinout used by
Cisco. Use straight through RJ-45 cabling to connect to equipment such as Cisco, Juniper, SUN, and
more.
PIN SIGNAL DEFINITION DIRECTION
1 CTS Clear To Send Input
2 DSR Data Set Ready Input
3 RXD Receive Data Input
4 GND Signal Ground NA
5 GND Signal Ground NA
6 TXD Transmit Data Output
7 DTR Data Terminal Ready Output
8 RTS Request To Send Output
Conventional Cat5 cabling with RJ45 jacks are used for serial connections. Before connecting the console
port of an external device to the Console Server serial port, confirm that the device supports standard
RS-232C (EIA-232).

17
The Console Server also has a DB9 LOCAL (Console/Modem) port. This DB-9 connector is on the rear
panel of the B092-016 Console Server, and on the front panel of the B096-048/016 Console Server
Management Switch.
2.5 USB Port Connection
The B096-048/016 Console Server Management Switch has one USB port on the front panel. External
USB devices can be plugged into this USB port. The B096-048/016 Console Server Management Switch
ships with a USB memory stick so that it will be installed in this port for extended log file storage.
There are four USB 2.0 ports on the rear panel of the B092-016 Console Server. These ports are used to
connect to USB consoles (of managed UPS hardware) and to other external devices (such as a USB
memory stick or keyboard).
External USB devices (including USB hubs) can be plugged into any Console Server USB port.
2.6 Rackmount Console / KVM Connection (B092-016 only)
B092-016 Console Server with PowerAlert can be connected directly to a rack mount console (such as
B021-000-17 or B021-019 by Tripp Lite) to provide direct local management right at the rack. Connect
the rack mount console’s PS/2 Keyboard/Mouse and VGA connectors directly to the PS/2 and VGA
connectors on the B092-016. The default video resolution is 1024 x768. The B092-016 Console Server
also supports the use of a USB keyboard/mouse.
Alternately, the B092-016 Console Server can also be connected locally to a KVM (or KVMoIP) switch at
the rack. The B092-016 Console Server with PowerAlert will enable you then to use this KVM
infrastructure to run PowerAlert, to manage your power devices and to run the thin clients to manage
other devices.
Note Care should be taken in handling all Console Server products. There are no operator-serviceable
components inside, so do not remove cover. Refer any service to qualified personnel

18
3. INITIAL SYSTEM CONFIGURATION
Introduction
This chapter provides step-by-step instructions for the initial configuration of your Console Server and
connecting it to your management or operational network. This involves the Administrator:
Activating the Management Console
Changing the Administrator password
Setting the IP address for the Console Server’s principal LAN port
Selecting the network services to be supported
This chapter also discusses the communications software tools that the Administrator may use to access
the Console Server. It also covers the configuration of the additional LAN ports on the B096-016/048
Console Server Management Switch.
3.1 Management Console Connection
Your Console Server has a default IP Address 192.168.0.1 Subnet Mask 255.255.255.0
Directly connect a computer to the Console Server
Note For initial configuration it is recommended that the Console Server be connected directly to a
single computer. However, if you choose to connect your LAN before completing the initial setup
steps, it is important that:
you ensure there are no other devices on the LAN with an address of 192.168.0.1
the Console Server and the computer are on the same LAN segment, with no interposed router
appliances
3.1.1 Connected computer set up
To configure the Console Server with a browser, the connected computer should have an IP address in
the same range as the Console Server (e.g. 192.168.0.100):
To configure the IP Address of your Linux or Unix computer simply run ifconfig
For Windows computers (Win9x/Me/2000/XP/ Vista/ NT):
Click Start -> (Settings ->) Control Panel and double click Network Connections (for
95/98/Me, double click Network).
Right-click on Local Area Connection and select Properties
Select Internet Protocol (TCP/IP) and click Properties
Select Use the following IP address and enter the following details:

19
oIP address: 192.168.0.100
oSubnet mask: 255.255.255.0
If you wish to retain your existing IP settings for this network connection, click Advanced
and Add the above as a secondary IP connection.
If it is not convenient to change your computer network address, you can use the ARP-Ping
command to reset the Console Server IP address. To do this from a Windows computer:
Click Start -> Run
Type cmd and click OK to bring up the command line
Type arp –d to flush the ARP cache
Type arp –a to view the current ARP cache which should be empty
Now add a static entry to the ARP table and ping the Console Server to have it get the IP
address. In the example below we have a Console Server with a MAC Address 00:13:C6:00:02:0F
(designated on the label on the bottom of the unit) and we are setting its IP address to
192.168.100.23. The computer issuing the arp command must be on the same network segment
as the Console Server (i.e. have an IP address of 192.168.100.xxx)
Type arp -s 192.168.100.23 00-13-C6-00-02-0F (Note for UNIX the syntax is: arp -s
192.168.100.23 00:13:C6:00:02:0F)
Type ping -t 192.18.100.23 to start a continuous ping to the new IP Address.
Turn on the Console Server and wait for it to configure itself with the new IP address. It will
start replying to the ping at this point
Type arp –d to flush the ARP cache again
3.1.2 Browser connection
Activate your preferred browser on the connected computer and enter https://192.168.0.1 The
Console Server supports all current versions of the popular browsers (Netscape, Internet
Explorer, Mozilla Firefox and more)

20
You will be prompted to log in. Enter the default
administration username and administration
password:
Username: root
Password: default
The above screen, which lists four initial installation configuration steps, will be displayed:
1. Change the default administration password on the System/Administration page (Chapter 3)
2. Configure the local network settings on the System/IP page (Chapter 3)
3. Configure port settings and enable the Serial & Network/Serial Port page (Chapter 4)
4. Configure users with access to serial ports on the Serial & Network/Users page (Chapter 3)
After completing each of the above steps, you can return to the configuration list by clicking in the top
left corner of the screen on the logo:
Note If you are not able to connect to the Management Console at 192.168.0.1 or if the default
Username / Password were not accepted then reset your Console Server (refer to Chapter 10)